Craftsman CMXEVBE17678 User manual

Part No. SP7084 Printed in Mexico

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1.75 PEAK HP VACUUM POWERHEAD WET/DRY VAC

ASPIRATEUR DE LIQUIDES ET DE POUSSIÈRES

AVEC BLOC-MOTEUR À DÉPRESSION DE 1,75 HP CRÊTE

ASPIRADORA PARA SECO/MOJADO CON CABEZA MOTRIZ

DE ASPIRACIÓN DE 1,75 HP PICO

CMXEVBE176780

1-888-331-4569 WWW.CRAFTSMAN.COM

SP7084-1 CMXEVBE176780.indb 1 8/3/19 7:22 AM

2

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

Components

Fig. A

2

6

5

1

4

3

1 Powerhead Assembly

2 Filter Bag and Retainer Band

3 Inlet Port

4 ON/OFF Switch

5 Power Cord

6 Blowing Port

If you have any questions or comments about this or

any product, call CRAFTSMAN toll free at:

1-888-331-4569.

WARNING: Read all safety

warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

WARNING: Never modify the

product or any part of it. Damage or personal injury

could result.

WARNING: To reduce the risk of

injury, read the instruction manual.

!

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided, may result in minor or moderate

injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

!

SP7084-1 CMXEVBE176780.indb 2 8/3/19 7:22 AM

3

IMPORTANT SAFETY INSTRUCTIONS

• This Wet/Dry Vac is not intended for use by persons

(including children) with reduced physical, sensory,

or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

• Do not use with a torn filter or without the filter

installed except when vacuuming liquids as described

in this manual. Dry debris ingested by the impeller may

damage the motor or be exhausted into the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

• Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

• Do not use with damaged cord, plug, or other parts.

If your Vac is not working as it should, has missing parts,

has been dropped, damaged, left outdoors, or dropped

into water, call customer service at 1-888-331-4569

(Mexico 001-881-331-4569).

• Do not pull or carry by cord, use cord as handle, close a

door on cord, or pull cord around sharp edges or corners.

Keep cord away from heated surfaces.

• Do not handle plug, switch, or the Vac with wet hands.

• To reduce the risk of electric shock, use only extension

cords that are rated for outdoor use and have a grounding

conductor. Extension cords in poor condition or too small

in wire size can pose fire and shock hazards. To reduce

the risk of these hazards, be sure the cord is in good

condition and that liquid does not contact the

connection. Do not use an extension cord with

conductors smaller than 1,3 mm

2

(16 AWG) in size.

• Connect only to a properly grounded outlet.

See grounding instructions.

• Do not put any object into ventilation openings. Do not

vacuum with any ventilation openings blocked; keep

free of dust, lint, hair, or anything that may reduce air

flow.

• Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning

on stairs.

• To reduce the risk of tip-over when carrying by

bucket handle/bale, be sure handle/bale is snapped into

retention notches in latches.

• To reduce the risk of personal injury or damage to Vac,

use only CRAFTSMAN recommended accessories.

• Read and understand this manual and all labels on the

Vac before operating.

• Use only as described in this manual.

• Do not leave Vac running while unattended - you may fail

to notice important signs indicating abnormal operation

such as loss of suction, debris/liquid exiting exhaust, or

abnormal motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac when plugged in. Unplug from outlet

when not in use and before servicing.

• TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY

BUCKETS WITH THE FOLLOWING UPCs NUMBERS:

ACE® - 0 28901 08836 3,

Amazon - 8 84305 35557 7,

Lowe’s® - 0 51596 10055 1,

Tractor Supply Company® - 0 12891 95001 2,

0 64784 73118 5,

Menards® - 0 17581 30505 9,

CANAC® - 2 01102 14080 3,

Canadian Tire - 6 28076 19101 1,

Orchard Supply Hardware® - 0 26703 05500 0.

The Home Depot® - 0 26703 05555 0, 0 84305 35554 6,

0 62602 00582 1, or 7 501058 561596.

• Sparks inside the motor can ignite flammable vapors or

dust. To reduce the risk of fire or explosion, do not use near

combustible liquids, gases, or dusts, such as gasoline or

other fuels, lighter fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain dust, aluminum

dust, or gun powder. Do not use on a bucket that contains

residuals of such vapors or dusts.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• To avoid the risk of self-ignition of bucket debris, empty

bucket after each use. Combustible materials, such as rags

or saw dust containing stain or urethane, can be sources of

such overheating.

• Do not vacuum drywall dust, cold fireplace ash, or other

fine dusts, which may pass through the filter bag and be

exhausted back into the air.

• To reduce the risk of inhaling toxic vapors, do not vacuum or

use near toxic or hazardous materials.

• To reduce the risk of electric shock, do not expose to rain or

allow liquid to enter motor compartment. Store indoors.

WARNING:

To reduce the risk of fire, electric shock, or injury:

!

When using this Vac, always follow basic safety

precautions including the following:

SP7084-1 CMXEVBE176780.indb 3 8/3/19 7:22 AM

4

Observe the following warnings that appear on the motor

housing of your Vac:

WARNING:

• TO REDUCE THE RISK OF INJURY, USER MUST READ

INSTRUCTION MANUAL.

• TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY

BUCKETS WITH THE FOLLOWING UPCs NUMBERS:

ACE® - 0 28901 08836 3,

Amazon - 8 84305 35557 7,

Lowe’s® - 0 51596 10055 1,

Tractor Supply Company® - 0 12891 95001 2,

0 64784 73118 5,

Menards® - 0 17581 30505 9,

CANAC® - 2 01102 14080 3,

Canadian Tire - 6 28076 19101 1,

Orchard Supply Hardware® - 0 26703 05500 0.

The Home Depot® - 0 26703 05555 0,

0 84305 35554 6, 0 62602 00582 1,

or 7 501058 561596.

• Do not leave running while unattended.

• Do not pick up hot ashes, coals, toxic, combustible/

self-igniting, flammable or other hazardous materials,

or use around explosive liquids or vapors, including

residuals leftover in the bucket.

• When using as a blower:

- Direct air discharge only at work area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except blowing dirt and

debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear safety eyewear.

The operation of any utility Vac or blower can result in

foreign objects being blown into the eyes, which can

result in severe eye damage.

CAUTION:

• To reduce the risk of hearing damage, wear ear

protectors when using for extended time or in a

noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the relative

humidity of the air is low. Vacuuming fine

debris with your Vac can deposit static charge

on the hose or Vac. To reduce the frequency of

static shocks in your home or when using this

Vac, add moisture to the air with a humidifier.

• Use only three-wire outdoor extension cords that

have three-prong grounding plugs and grounding

receptacles that accept the appliance’s plug.

• Maintain appliance with care.

WARNING:

To reduce the risk of electric shock - do not expose

to rain - store indoors.

SAVE THESE INSTRUCTIONS

WARNING:

• For your own safety, read and understand Instruction

Manual.

• Do not run unattended.

• Do not pick up hot ashes, coals, toxic, combustible/

self-igniting, flammable or other hazardous materials.

• Do not use around explosive liquids or vapors.

WARNING:

To reduce the risk of personal injury due to a loose

electrical connection between the appliance’s plug and

extension cord, firmly and fully attach the appliance

plug to the extension cord. Periodically check the

connection while operating to ensure it is fully attached.

Do not use an extension cord that provides a loose

connection. A loose connection may result in

overheating, fire, and increases the risk of a burning.

!

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a free replacement.

SP7084-1 CMXEVBE176780.indb 4 8/3/19 7:22 AM

5

This Powerhead Assembly is intended to be used only with

a 5 U.S. Gallon (19 Liter) plastic bucket, approximately

14-1/2 inches (368 mm) tall with a top diameter of

11-3/4 inches (298 mm) with a 10 gauge steel wire,

bale-type handle.

This bucket is available from many home improvement

locations as listed in the manual.

With this bucket you have a Vac that is intended for

household use.

It may be used for light vacuuming of wet or dry media

and may also be used as a blower. The light-weight design

allows usage for many small household vacuuming chores.

Familiarize yourself with the product and read the

entire instruction manual for specific usage of your new

Wet/Dry Vac.

INTRODUCTION

Section Page

Important Safety Instructions.......................2-4

Introduction .......................................5

Grounding Instructions..............................6

Carton Contents ....................................7

Installation ......................................8-9

Powerhead Assembly .............................8

Powerhead Disassembly...........................8

Insert Hose ......................................9

Power Cord Storage...............................9

Hose Assembly Storage............................9

Operation .....................................10-12

ON/OFF Switch ..................................10

Vacuuming Dry Materials .........................11

Vacuuming Liquids ..............................11

Emptying the Bucket.............................12

Blowing Feature.................................12

Maintenance...................................13-14

Filter Bag Cleaning ..............................13

Filter Bag Removal and Replacement...............13

Storage ........................................13

Cleaning and Disinfecting the Wet/Dry Vac ..........14

Troubleshooting...................................14

Warranty .........................................15

TABLE OF CONTENTS

SP7084-1 CMXEVBE176780.indb 5 8/3/19 7:22 AM

6

This Vac must be Grounded. If it should malfunction

or break down, Grounding provides a path of least

resistance for Electric Current to reduce the risk of

Electric Shock. This Vac is equipped with a Cord having an

Equipment-Grounding Conductor and Grounding Plug.

The Plug must be inserted into an Appropriate Outlet that

is properly installed and Grounded in accordance with all

Local Codes and Ordinances.

Properly

Grounded

Outlet

Grounding

Prong

3-Prong

Plug

GROUNDING INSTRUCTIONS

Fig. B

WARNING:

Improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service person if you are

in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance -

if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

!

This Vac is for use on a Nominal 120 Volt Circuit, and has a

Grounded Plug that looks like the Plug shown.

A Temporary Adapter that looks like the Adapter shown

may be used to connect this Plug to a 2-Pole Receptacle,

as shown. If a properly Grounded Outlet is not

available, the Temporary Adapter should be used only

until a properly Grounded Outlet can be installed by a

Qualified Electrician.

The Green Colored Rigid Ear, Lug or the like extending

from the Adapter must be connected to a Permanent

Ground such as a properly Grounded Outlet Box Cover.

Whenever the Adapter is used, it must be held in place

by a Metal Screw.

NOTE: In Canada, the use of a Temporary Adapter is Not

Permitted by the Canadian Electrical Code.

Fig. C

Make sure this is a

metal screw connected

to a known ground

Green

Grounding Lug

Metal

Screw

3-Prong Plug

Adapter

2-Prong Outlet

SP7084-1 CMXEVBE176780.indb 6 8/3/19 7:22 AM

7

Remove entire contents of carton. Check each item against

the Carton Contents List.

If any parts are damaged or missing, immediately call

Customer Service at 1-888-331-4569

(Mexico 001-881-331-4569).

CARTON CONTENTS (Fig. D)

Fig. D

Key Description Qty.

A Powerhead Assembly 1

B Hose Assembly 1

C Filter Bag 1

D Retainer Band 1

E Instruction Manual 1

Filter Bag and retainer band may already assembled.

NOTE: See Repair Parts List for Part Number.

C

D

E

A

B

SP7084-1 CMXEVBE176780.indb 7 8/3/19 7:22 AM

8

Powerhead Assembly (Figs. E & F)

1. Align the Powerhead Assembly Latches with the

Bucket Handle/Bale.

2. Press down firmly over each Latch to engage the

Latches with the Bucket.

INSTALLATION

Powerhead

Latch (2)

Bucket

Handle/Bale

Fig. E

3. Lift the Bucket Handle/Bale to snap into the Retention

Notches of the Latches.

Fig. F

Powerhead Disassembly (Fig. G)

1. To remove the Powerhead Assembly from the

Bucket, FIRST, unplug the Power Cord from the Wall

Receptacle.

2. Remove the Hose from the Powerhead Assembly and

rotate the Bucket Handle/Bale away from the Power

Cord.

3. Slightly spread both Latches away from the Bucket.

4. Lift the Powerhead Assembly off the Bucket.

NOTE: To reduce the risk of tip-over when carrying by the

Handle/Bale, align the Powerhead Latches above the Bale

attach points and be sure the Bale is snapped into the

Retention Notches on the Latches.

Fig. G

Powerhead

Latch (2)

Bucket

Handle

Power

Cord

Retention

Notch

Powerhead

Latch (2)

Bucket Handle

Retention

Notch

Bail Attach

Point

Powerhead

Latch (2)

Bucket Handle

Retention

Notch

Bale

Attach

Point

Bucket

*Installation shown is for wet pick up applications.

SP7084-1 CMXEVBE176780.indb 8 8/3/19 7:22 AM

9

Insert Hose (Fig. H)

Insert the Hose Assembly into the Powerhead Assembly

Inlet Port (Located Near the Power Switch). The Hose

should be secure into place.

To remove the Hose Assembly from the Powerhead

Assembly: Twist and pull out on the Hose Assembly to

release the Hose from the Powerhead Assembly Inlet Port.

Hose

Powerhead Assembly

ON/OFF Switch

Powerhead

Assembly

Inlet Port

Fig. H

Hose Assembly Storage (Fig. J)

The Hose Assembly may also be stored inside the Vac

Bucket.

CAUTION:

Do not operate vacuum while the hose or accessories

are stored inside the wet/dry vac’s bucket.

WARNING:

Do not put any object into ventilation openings.

Do not vacuum with any ventilation openings blocked;

keep free of dust, lint, hair or anything that may reduce

air flow.

Power Cord Storage (Fig. I)

The Power Cord should be wrapped around the Powerhead

Assembly.

Snap the Cord Clip onto the Power Cord, to secure in place.

Cord Clip

Power

Cord

Powerhead

Assembly

Fig. I

Hose

Assembly

(Stored

Inside

Bucket)

Fig. J

!

SP7084-1 CMXEVBE176780.indb 9 8/3/19 7:22 AM

10

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac/Blower for extended

time or in a noisy area.

OPERATION

WARNING:

To reduce the risk of electric shock or injury:

• Do not leave Vac running while unattended - you

may fail to notice important signs indicating

abnormal operation such as loss of suction,

debris/liquid exiting the exhaust, or abnormal

motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off

suction.

• Sparks inside the motor can ignite airborne

flammables. Do not operate Vac near

flammable liquids or in areas with flam-

mable gases, vapors, or explosive/

airborne dust. Flammable liquids,

gases, and vapors include: lighter fluid,

solvent-type cleaners, oil-based paints,

gasoline, alcohol, and aerosol sprays. Explosive

dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable

liquids, or hot ashes.

• Do not leave sawdust or rags with stain or

polyurethane residue inside Vac. Empty bucket

after picking up these potentially self-heating

materials.

• Do not expose to rain or allow liquid to enter

motor compartment. Store indoors.

• Do not handle plug, switch, or Vac with wet

hands.

• Unplug Vac before servicing. If your Vac is

not working as it should, has missing parts,

has been dropped, damaged, left outdoors,

or dropped into water, call customer service at

1-888-331-4569 (Mexico 001-881-331-4569).

• When using an extension cord, use only

outdoor-rated cords that are in good condition.

Do not allow the connection to come into contact

with liquid.

=

OFF

=

ON

ON/OFF Switch (Fig. K)

After you Plug the Power Cord into the Outlet, turn the Unit

on by pushing the Switch from position “O” to position “l”.

The symbols used on the Switch Actuator are International

“On & Off” Symbols:

"O" - "OFF"

Position

"I" - "ON"

Position

Fig. K

WARNING:

To reduce the risk of fire, explosion, or dam-

age to Vac:

!

SP7084-1 CMXEVBE176780.indb 10 8/3/19 7:22 AM

11

Vacuuming Liquids (Fig. M)

WARNING:

Do not remove the cage and float. The float prevents

liquid from entering the impeller and damaging the

motor. The cage prevents fingers from touching the

moving impeller.

WARNING:

To reduce the risk of fire or explosion, do not vacuum

flammable or combustible liquids, gases or dust.

Vacuuming Dry Materials (Fig. L)

1. The Filter Bag must always be in correct position to

reduce the risk of leaks and possible damage to Vac.

Make sure that the Filter Bag is completely covering

the Filter Cage and that the Retainer Band is as close to

the Powerhead Assembly as possible. Make sure there

are no gaps between the Filter Bag and the Powerhead

Assembly.

NOTE: It is very important to assemble the Filter Bag to

the cage without allowing any possible leaks or tears.

Any leaks will allow the picked up media to be blown

out of the Blower Port and back into the surrounding

environment.

2. When using your Vac to pick up very fine dust,

it will be necessary for you to empty the Bucket and

clean or replace the Filter Bag at more frequent

intervals to maintain peak Vac performance.

See “Replacing the Filter” in the Maintenance section

for complete details.

NOTE: A dry Filter Bag is necessary to pick up dry material.

If you use your Vac to pick up dust when the Filter Bag is

wet, the Filter Bag will clog quickly and be very difficult

to clean. In case the Filter Bag gets wet, replace it before

continuing to do dry pickups.

Fig. L

Retainer

Band

Filter

Bag

Rib Tab

Lid

1. Removal of the Filter Bag is highly recommended for

wet pickups.

2. This Wet/Dry Vac is equipped with a Float Mechanism

which will rise automatically to cut off the airflow when

the liquid in the Bucket reaches a predetermined

level. When this happens, turn OFF Vac, unplug the

Power Cord, and empty the Bucket. You will know that

the Float has shut the airflow off because the suction

ceases and the motor noise becomes higher in pitch,

due to increased motor speed. The liquid capacity may

vary with the rate of pickup.

3. If a Filter Bag was used for wet pickup, be sure to

replace Filter Bag after wet pickup. Never pick up dry

debris without the Filter Bag properly installed.

IMPORTANT: To reduce the risk of damage to the Vac

do not run Motor with Float in raised position.

Fig. M

Float In

Raised

Position

!

SP7084-1 CMXEVBE176780.indb 11 8/3/19 7:22 AM

12

1. Remove the Powerhead Assembly: Pull Powerhead

Assembly Latches outward to release from the Bucket.

2. Lift the Powerhead Assembly up and away from the

Bucket.

3. Lay Powerhead Assembly upside down on a clean area

while emptying the Bucket.

4. Dump the Bucket contents into the proper waste

disposal container.

Emptying the Bucket (Fig. N)

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before emptying the bucket.

Fig. N

Bucket

Your Vac features a Blowing Port. It can blow sawdust and

other debris. Follow the following steps to use your Vac

as a Blower.

1. Locate the Blowing Port on the back of your Powerhead

Assembly.

2. Insert one End of the Hose Assembly into the

Powerhead Assembly Blowing Port. The Hose should

be secure into place.

To remove the Hose from the Powerhead Assembly:

Twist and pull out on the Hose Assembly to release the

Hose from the Powerhead Assembly Blowing Port.

3. (Optional) Attach an Accessory to opposite end of

Hose.

4. Turn Powerhead Assembly ON and you are ready to

use your Vac as a Blower.

Blowing Feature (Fig. O)

Fig. O

Blowing Port

Hose

!

WARNING:

Always wear safety eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before using as a blower.

WARNING:

To reduce the risk of injury to bystanders, keep them

clear of blowing debris.

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac / Blower for extended

time or in a noisy area.

CAUTION:

Wear a dust mask if blowing creates dust which might

be inhaled.

!

SP7084-1 CMXEVBE176780.indb 12 8/3/19 7:22 AM

13

MAINTENANCE

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

Filter Bag Cleaning

Your Filter should be cleaned often to maintain peak Vac

performance.

After dirty Filter Bag removal from the Powerhead

Assembly, remove the dry debris by gently tapping Filter

against the inside wall of the disposal container.

NOTE: Clean the Filter Bag in an open area. Cleaning

should be done outdoors and not in the living quarters.

IMPORTANT: After cleaning, check the Filter Bag for tears

or small holes. Tears and holes in the Filter Bag can cause

debris and dust to be blown from the Vac. Do not use a Filter

Bag with holes or tears. Replace immediately.

NOTE: See Repair Parts List for Part Number.

NOTE: Before installing the Filter Bag on the Vac, clean the

area of the Powerhead Assembly so that the Retainer Band

will seal the bag against the Powerhead Assembly and stop

small particles from bypassing the Filter Bag.

If the Filter Bag is clean and not damaged, replace it on the

Filter Cage. If it cannot be reused, place a new Filter Bag over

the Filter Cage.

Filter Bag Removal and Replacement

(Fig. P)

IMPORTANT: To avoid damage to the Blower Wheel and

Motor, always reinstall the Filter Bag before using the Vac for

dry material pick-up.

1. Extend the Retainer Band around the Plastic Posts on

the Powerhead Assembly.

2. Remove Filter Bag off the Filter Cage.

3. Place the replacement Filter Bag on the Filter Cage

until open end touches bottom of the Powerhead

Assembly.

4. Release the Retainer Band from the Plastic Post on the

Powerhead Assembly, holding the Filter Bag secure to

the Powerhead Assembly.

5. Make sure the Retainer Band is positioned on the Filter

Bag between the printed lines.

Powerhead

(upside-down)

Filter

Bag

Lid

Retainer Band

Filter Bag

Rib Tab

Lid

Fig. P

Storage

Before storing your Vac, the Bucket should be emptied and

cleaned. The Power Cord should be wrapped around the

Carry Handle and the Hose should be stored as described in

this manual. Accessories should be kept in the same area as

the Vac so they can be readily available. The Vac should be

stored indoors.

!

SP7084-1 CMXEVBE176780.indb 13 8/3/19 7:22 AM

14

Troubleshooting

Problem Cause Remedy

Vac will not pick up dirt. 1. Clogged Filter. 1. Clean or replace Filter Bag (Follow instructions on Page 13).

2. Clogged Hose. 2. Remove Hose and clear debris.

3. Air leak. 3. Make sure Powerhead Assembly is securely attached

to Bucket.

Vac will not run. 1. No electricity. 1. Make sure electrical outlet has voltage.

(A qualified electrician may need to be contacted).

Vacuum Powerhead Wet/Dry Vac

Model Number: CMXEVBE176780

Electrical Ratings: 120 V~ 4 A 60 Hz

Replacement Filter Bags are available where you

purchased your Vac.

The Part Number is CMXZVBE38737.

Replacement Filter Bag (Fig. R)

Fig. R

WARNING:

To assure product SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments should be

performed by Authorized Service Centers, always using

CRAFTSMAN replacement parts.

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its best, clean the outside

with a cloth dampened with warm water and mild soap.

To clean the Bucket:

1. Dump debris out.

2. Wash the Bucket thoroughly with warm water and mild

soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed (i.e., waste water pick

up) the Bucket should be disinfected.

To disinfect the Bucket:

1. Pour 1 gallon (4 L) of water and 1 teaspoon (5 mL)

chlorine bleach into the Bucket.

2. Let solution stand for 20 minutes, carefully swishing

every few minutes, making sure to wet all inside surfaces

of the Bucket.

3. Empty Bucket after 20 minutes. Rinse with water until

bleach smell is gone. Allow Bucket to dry completely

before sealing the Motor on the Bucket.

!

WARNING:

If any of the powerhead assembly parts should become detached or broken, exposing motor or any other electrical

components, operation should be discontinued immediately to avoid personal injury or further damage to the vacuum.

This vacuum has no user serviceable parts, except the filter.

!

SP7084-1 CMXEVBE176780.indb 14 8/3/19 7:22 AM

15

CRAFTSMAN

®

LIMITED WARRANTY – 3 YEARS

This limited warranty is provided by Emerson Tool Company, a division of Emerson Electric Co., (“We” or “Our” or “Us”) to

the original consumer owner (“Customer” or “You” or “Your”) of the CRAFTSMAN product with which this limited warranty

is provided (the “CRAFTSMAN Product”).

What is Covered

We warrant to You that your CRAFTSMAN Product will be free from defects in materials and workmanship when used

under normal conditions in accordance with the terms of the Instruction Manual provided to You with the CRAFTSMAN

Product, subject to the exclusions described below, for a period of three years commencing on the date of purchase by

You (the “Warranty Period”). This limited warranty terminates if the original purchaser transfers the CRAFTSMAN Product

to any other person or entity.

What is not Covered

This limited warranty does not extend to and expressly excludes:

• Normal wear and tear and/or replacement attachments or accessories, including, without limitation, power cords,

hoses, filters, and other attachments or accessories that may be offered for sale by Us for use with the CRAFTSMAN

Product.

• Damage or burnout of the CRAFTSMAN Product motor resulting from failure to clear a blockage occurring during the

normal course of use.

• Loss or damage to the CRAFTSMAN Product resulting from conditions beyond Our control including without

limitation, misuse, accident, abuse, neglect, negligence (other than Our’s), overuse beyond intended capacity as set

forth in the Instruction Manual, or modifications or alterations made by anyone other than Us.

• Loss or damage to the CRAFTSMAN Product resulting from failure to use the CRAFTSMAN Product in accordance with

the written instructions, guidelines, and terms and conditions set forth in the Instruction Manual.

• TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE,

USE, MISUSE OR INABILITY TO USE THE CRAFTSMAN PRODUCT OR FOR THE NEGLIGENCE OF ETC.

How to Obtain Service

US and Canada – To obtain warranty benefits contact us toll free at 1-888-331-4569 (Mexico 001-881-331-4569).

We will direct you to the nearest service center to review your vacuum for inspection, repairs or replacement.

Mexico - To obtain warranty benefits contact us toll free at 001-881-331-4569. We will direct you to the nearest service

center to review your vacuum for inspection, repairs or replacement.

No Other Express Warranty Applies

This limited warranty is the sole and exclusive warranty provided to You. No other express warranty, written or verbal,

applies including, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on

behalf of Us.

What We will do to Correct Problems

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR, REPLACEMENT,

REFUND OF THE CRAFTSMAN PRODUCT.

After You have contacted CRAFTSMAN Product Customer Service Department, We will initiate warranty proceedings,

including a physical inspection, subject to the exclusions and the Warranty Period stated herein, to determine whether to

repair or replace the CRAFTSMAN Product or provide You with a refund.

The decision to repair or replace your CRAFTSMAN Product or to provide a refund is at Our sole discretion. Repair or

replacements provided to You by ETC are at no cost to You if covered under this limited warranty.

If we are unable to provide You with a suitable repaired or replacement CRAFTSMAN Product, we will provide you with

a refund equal to the purchase price of your CRAFTSMAN Product or a credit to be used toward the purchase of a new

CRAFTSMAN Product.

In the event of any dispute between CUSTOMER AND US, either party may choose to resolve the dispute by binding

arbitration. THIS MEANS IF EITHER CUSTOMER OR US CHOOSE BINDING ARBITRATION, NEITHER PARTY SHALL HAVE THE

RIGHT TO LITIGATE SUCH CLAIM IN COURT OR HAVE A JURY TRIAL. DISCOVERY AND APPEAL RIGHTS ARE LIMITED.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary from State to State.

Some states do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply.

SP7084-1 CMXEVBE176780.indb 15 8/3/19 7:22 AM

Part No. SP7084 Form No. SP7084-1 Printed in Mexico 08/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marco registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.

est une morque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabrriqué par: U.S. & Candaga Only • É.-U. et Canada seulement

c

SP7084-1 CMXEVBE176780.indb 16 8/3/19 7:22 AM

Page is loading ...

Pièce N° SP7084 Imprimé N° SP7084-1 Imprimé au Mexique 08/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.

est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabriqué par : U.S. & Canada Only • É.-U. et Canada seulement

c

SP7084-1 CMXEVBE176780.indb 31 8/3/19 7:22 AM

Page is loading ...

46

NOTES

SP7084-1 CMXEVBE176780.indb 46 8/3/19 7:22 AM

Page is loading ...

Craftsman CMXEVBE17678 User manual

Craftsman CMXEVBE17678 User manual

in other languages

Related papers

Other documents