DeWalt SDS max D25890 Owner's manual

Brand: DeWalt

Model: SDS max D25890

Category: Power tools

Type: Owner's manual

This manual is also suitable for

'<o

>--rr

--S

rrl. u

!,!

o< d

oZU

OI--121

<n- O

rrWrr

©'F 0_

>ZD

r..) rr C3

rr_ m

t-- t--

_wz

_or.

E E

,,.a

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

(JUL05) Form No. 488039-00 D25701, D25730, D25890

The followingare trademarksforone or more DEWALTpowertools: the yellowandblackcolor scheme;the

"D"shaped air intakegrill;the array of pyramidson the handgrip;the kit box configuration;and the array of

lozenge-shaped humpson the surface ofthe tool.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules

_ WARNING! To reduce risk of injury, user must read instruction manual.

Failure to follow all instructions listed below may result in electric shock, fire

and/or serious injury. The term "power tool" in all of the warnings listed below

refers to your mains-operated (corded) power tool or battery-operated (cordless)

power tool

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and we# lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a power tooL Distractions can

cause you to lose control

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earth-

ed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tooL Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock. Replace or repair damaged cords.

Make sure your extension cord is in good condition. Use only 3-wire extension cords that

have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool's plug.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock. When using

an extension cord, be sure to use one heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage

number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury

b) Use safety equipment. Always wear eye protection. Safety equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate condi-

tions will reduce personal injuries.

c) A void accidental starting. Ensure the switch is in the off-position before plugging

in. Carrying power tools with your finger on the switch or plugging in power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught

in moving parts. Air vents often cover moving parts and should also be avoided.

g) ff devices are provided for the connection of dust extraction and collection facili-

ties, ensure these are connected and properly used. Use of these devices can reduce

dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tooL Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation, ff

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Safety Instructions for Rotary Chisel Hammers

• Hold power tools by insulated gripping surfaces when performing an operation where

the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

Be certain that the material being drilled does not conceal electric or gas service and that

their locations have been verified with the utility companies.

Wear ear protectors. Exposure to noise can cause hearing loss.

Use auxiliary handles supplied with the tool Loss of control can cause personal injury.

Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding #

with both hands. Operating this tool with one hand will result in loss of control Breaking

through or encountering hard materials such as re-bar may be hazardous as well. Tighten

the side handle securely before use.

• Wear safety goggles or other eye protection. Hammering operations cause chips to fly.

Flying particles can cause permanent eye damage. Wear a dust mask or respirator for appli-

cations that generate dust. Ear protection may be required for most applications.

• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without

holding it with both hands. It is recommended that the side handle be used at all times.

Operating this tool with one hand will result in loss of control Breaking through or encoun-

tering hard materials such as re-bar may be hazardous as well.

• Do not operate this tool for long periods of time. Vibration caused by hammer action may

be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure

by taking frequent rest periods.

• Do not recondition bits yourself. Chisel reconditioning should be done by an authorized

specialist. Improperly reconditioned chisels could cause injury.

• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and

bits may get extremely hot during operation. Small bits of broken material may damage bare

hands.

• Never lay the tool down until the bit has come to a complete stop. Moving bits could

cause injury.

• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or

material chips could dislodge and cause injury.

• Slightly worn chisels can be resharpened by grinding.

• Keep the power cord away from the rotating bit. Do not wrap the cord around any part

of your body. An electric cord wrapped around a spinning bit may cause personal injury and

loss of control

NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn chisels

require reforging. Do not reharden and temper chisels.

_ CAUTION: Wear appropriate personal hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

_ WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may pro-

mote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

• The label on your tool may include the following symbols.

V ................ volts

Hz .............. hertz

min ............ minutes

.... ............ direct current

[] ................ Class II Construction

@................ earthing terminal

BPM ..........beats per minute

A.................. amperes

W ................ watts

.............. alternating current

no ................ no load speed

.../min .......... revolutions or reciprocation per minute

_, ................ safety alert symbol

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Your tool is powered by a DEWALT built motor designed to be used with alternating current.

Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools

are factory tested; if this tool does not operate, check the power supply.

Components (Fig. 1)

A. Trigger switch

B. Lock-on slider

C. Side handle

D. Main handle

E. Active vibration control

R Mode selector

G. Electronic Speed and impact control dial

H. Clamp knob

I. Rear side handle position

Side Handle (Fig. 3)

CAUTION: Always operate the tool with the side handle properly assembled. Hold tool with

both hands to maximize control

The side handle clamps to the front barrel (collar) and may be rotated 360 ° to permit right-

or left-hand use. For operating convenience, the side handle can be installed in front or rear

positions.

TO MOUNT IN FRONT POSITION (FIG. 3)

1. Unscrew the side handle (C) and disassemble the side handle clamp (J).

2. Snap the steel ring (K) over the collar (L) behind the tool holder (M). Squeeze both ends of

the steel ring together. Mount the bushing (N) and insert the pin (O).

3. Slide the side handle clamp (J) and bushing into the clamp knob (H) - do not tighten.

4. Screw the side handle into the clamp knob (H) and tighten.

5. Rotate the side handle mounting assembly to the desired position. For drilling horizontally

with a heavy drill bit, place the side handle assembly at an angle of approximately 20 °to the

tool for optimum control.

6. Lock the side handle mounting assembly in place by tightening the clamp knob (H).

TO MOUNT IN REAR POSITION (FIG. 3)

1. Unscrew the side handle (C) and remove it from the side handle mounting assembly. Leave

the side handle mounting assembly in the front position.

2. Screw the side handle directly into one of the rear side handle positions (I) on either side of

the tool.

Active Vibration Control (Fig. 1)

For best vibration control, hold the tool with one hand on the main handle (D) and the other hand

on the side handle (C). Apply just enough pressure so the hammer is approximately mid-stroke.

The hammer only needs enough pressure to engage the active vibraton control. Applying too

much pressure will not make the tool drill or chip faster and active vibration control will not

engage.

Inserting and Removing SDS max TM Accessories (Fig. 3)

CAUTION: TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY.

1. Pull back the locking sleeve (P) and insert the bit shank. The bit shank must be clean and

slightly lubricated.

2. Turn the bit slightly until the sleeve snaps back into position.

3. Ensure the bit is properly engaged.

NOTE: The bit needs to move several centimeters in and out of the tool holder (M) when

properly engaged.

4. To remove the bit, pull back the locking sleeve and pull the bit out.

Complete Torque Control (Fig. 4)

A CAUTION: Always turn the tool off before changing torque control settings or damage to tool

may result.

The Complete Torque Control (CTC) feature of this tool is designed to provide additional control

by providing a two-stage clutch mechanism.

Clutch setting #1 (Q) is designed for most drilling applications and is designed to easily clutch

out when the drill bit encounters re-bar or other foreign substances.

Clutch setting #2 (R) is designed for higher torque applications such as core-bits and deep hole

drilling.

NOTE: Allow the motor housing to rotate a little while changing torque.

Each time the tool is plugged in, it will automatically default to clutch setting #1, the most

sensitive setting.

Electronic Speed and Impact Control (Fig. 4)

The electronic speed and impact control allows the use of smaller drill bits without the risk of bit

breakage, drilling into light and brittle materials without shattering and optimal tool control for

precise chiseling.

To set the control dial, turn the dial (G) to the desired level. The higher the number, the greater

the speed and impact energy. Dial settings make the tool extremely flexible and adaptable for

many different applications. The required setting depends on the bit size and hardness of

material being drilled.

Mode Selector (Fig. 1)

A CAUTION: Never change the mode while the unit is running.

_ CAUTION: Do not change to hammerdrill mode with chisel bit in tool holder. Personal injury

and damage to tool may result.

The D25701 and D25730 use two operating modes. To select the required operating mode,

rotate the mode selector (F) until the arrow points to the hammerdrilling or the chipping icon. The

D25890 uses only the chipping mode.

HAMMERDRILLING MODE (-T)

The tool simultaneously rotates and impacts the work. This mode is appropriate for all concrete

and masonry operations.

CHIPPING MODE (T)

The spindle lock is engaged during chipping mode so the tool impacts the work without

rotating. This mode is appropriate for light chipping, chiseling and demolition applications.

NOTE: In chipping mode, the hammerdrill can also be used as a lever to free a jammed drill bit.

CHISEL BIT ADJUSTMENT ( O )

Turn the mode selector to one ofthe chisel bit adjustment iconsto adjust the chisel tothe desired

position. There are 24 possible positions to set the angle of the chisel. After finding the desired

position, slightly maneuver the chisel bit back and forth to ensure the chisel is properly engaged.

Power Indicator Lights (Fig. 41

The red LED light (S) indicates a serious problem and the tool should be taken to a DEWALT

authorized service center for repair.

The yellow LED light (T) indicates when brushes are nearly worn and the tool needs servicing.

After approximately 8 hours of use, the motor will automatically shut off. The tool should be taken

to a DEWALT authorized service center for routine inspection and maintenance.

OPERATION

NOTE: Operating temperature of this tool is 19° to 104° F (-7 to +40° C). Using the tool outside

of this temperature range will decrease the life of the tool.

Switch (Fig. 1)

To turn the tool on, depress the trigger switch (A). To stop the tool, release the trigger switch. To

lock the trigger switch on, push the lock-on slider (B) upwards while depressing the trigger

switch.

To deactivate the lock-on slider, depress the trigger switch once then release.

The lock-on slider may only be activated in chisel mode. The machine will stop running when

trying to engage the lock-on slider in drill mode. The motor will stop if the lock-on slider is

activated when changing from chisel mode into drill mode.

SOFT START FEATURE

The soft start feature allows you to build up speed slowly, thus preventing the drill bit from

walking off the intended hole position when starting. The soft start feature also reduces the

immediate torque reaction transmitted to the gearing and the operator if the hammer is started

with the drill bit in an existing hole.

Drilling (D25701, D25730)

NOTE: The D25890 has only chipping mode with no drilling capability.

DRILLING WITH A SOLID BIT

1. Set the model selector to hammerdrilling mode.

FIG. 1

CHISEL BIT ADJUSTMENT MODE

MODE DE RC:GLAGE DU TREPAN ORDINAIRE

MODO DE AJUSTE DE LA BROCA DE CINCEL

HAMMERDRILLING MODE

MODE DE MARTEAU PERFORATEUR

MODO TALADRO PERCUTOR

CHISEL BIT ADJUSTMENT MODE

MODE DE RI_GLAGE DU TRC:PAN ORDINAIRE

MODO DE AJUSTE DE LA BROCA DE CINCEL

CHIPPING MODE

MODE DE BURINAGE

MODO CINCEL

FIG. 2

O J

FIG. 3

p L

FIG. 4

2. Move the torque control lever to Setting 1 (Q).

3. Set the speed and impact control dial.

4. Insert the appropriate drill bit.

5. Adjust the side handle (front or rear position).

6. Mark the spot where the hole is to be drilled.

7. Place the drill bit on that mark and depress the trigger switch.

8. Apply only enough pressure to engage active vibration control (refer to Active Vibration

Control).

9. Tostop the tool, release the trigger switch. Always turn the tool off when work is finished and

before unplugging.

DRILLING WITH A CORE BIT

_&CAUTION: Do not use a core b# for drilling wood. Personal injury and damage to tool may

result.

1. Set the model selector to hammerdrilling mode.

2. Move the torque control lever to Setting 2 (R).

3. Turn the speed and impact control dial to the maximum torque position.

4. Adjust the side handle (front or rear position).

5. Assemble the centering bit and adapter shank into core bit.

6. Mark the spot where the hole is to be drilled.

7. Place the centering bit on that mark and depress the trigger switch.

NOTE: Some core drills require the removal of centering bit after about lcm of penetration. If

so, remove and continue drilling.

8. When drilling through a structure thicker than the depth of the core bit, break away the

round cylinder of concrete or core inside the bit at regular intervals. To avoid unwanted

breaking away of concrete around the hole, first drill a hole the diameter of the centering

bit completely through the structure. Then drill the cored hole halfway from each side of

the structure.

9.Tostopthetool,releasethetriggerswitch.Alwaysturnthetooloffwhenworkisfinishedand

beforeunplugging.

Chipping and Chiseling

(D25701, D25730, D25890)

1. Set the model selector to chipping mode.

2. Set the impact control dial to desired setting (refer to Electronic Speed and Impact

Control).

3. Insert the appropriate chisel and rotate it by hand to lock it into the desired position.

NOTE: For SDS max models, only use SDS max insert tools.

4. Adjust the side handle (front or rear position).

5. Depress the trigger switch.

6. Apply only enough pressure to engage active vibration control (refer to Active Vibration

Control).

7. To stop the tool, release the trigger switch. Always turn the tool off when work isfinished and

before unplugging.

MAINTENANCE

Cleaning

CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap.

Accessories

Recommended accessories for use with your tool are available at extra cost from your local deal-

er or authorized service center. Ifyou need assistance in locating any accessory, please contact

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT

1-800-433-9258) or visit our website www.dewalt.com.

CAUTION: The use of any other accessory not recommended for use with this tool could be

hazardous.

MAXIMUM CAPACITY

D25701 D25730 D25890

Concrete 1-7/8" (48mm) 2" (52mm) --

RPM 137-275 125-250 --

No load BPM 1260-2520 1150-2300 1150-2300

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments

(including brush inspection and replacement) should be performed by a DEWALT factory

service center, a DEWALT authorized service center or other qualified service personnel.

Always use identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear

or tool abuse. For further detail of warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights which vary in certain

states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

2 YEARS FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first two years after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt

for a full refund - no questions asked.

RECONDITIONED PRODUCT: Reconditioned product is covered under the 1 Year Free

Service Warranty. The 90 Day Money Back Guarantee and the Three Year Limited Warranty do

not apply to reconditioned product.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are miss-

ing, call 1-800-4-DEWALT for a free replacement.

DXXXXX

SER,

_ TO REDUCE THE RJSR OF

iNJURY, USERMUSTREAD

AND UNDERSTAND THE iNSTRUCTiON MANUAL.

ALWAYSUSE PROPEREYEAND RESPIRATORY

PROTECTION.ALWAYS USESiDE DANDLE.

PARA RiSMiNUiR

EL RiES60 DE

LERIONES,EL UGUARIOREBER/_LEERY COMPRENDER EL

MANUAL REINSTRU(_CiONES.SIEMPRE SEGERESA

LLEVARLAP.RUTECCJONAPROPJADAPARA LA VISTA Y

PARA LAGVIAS RESPiSATGRIAS. UTJLiCESiEMPRE LA

MANiJA LATERAL.

AFiN DE

MINiMiSES

LEGRiSQUESDERLESSURES,L'UTJLiSATEURDOJT

TOUJOURS LJRE ET COMPRENBRE LE GUIDE

R']/TJUSATJON, JLEAUT TQUJOURS PORTER RE

L'EQUiPEMENT DE PROTEC.TJON OCULAIRE ET

RESPJRATOJREAPPROPRiE.TOUJOURSUTJLiSERLA

POJGNEE LATERALE,

DEWALT INDUSTRIAL TOOL CO., BALFIMORE, MR 21286 USA

FOR SERVICE iNFORMATiON, CALL 1-800-4-DEWALT

www.DEWALT.com

, J

POUR TOUT RENSEIGNEMENT SUPPLI2MENTAIRE SUR CET OUTIL OU TOUT AUTRE

OUTIL DEWALT, COMPOSER SANS FRAIS LE NUMI2RO •

1-800-4-DEWALT (1-800-433-9258)

R_gles de s_curit_ - G_n_ralit_s

_k VERTISSEMENT ! Afin de r_duire le risque de blessures, I'utilisateur doit

/ire le mode d'emploi.

Tout manquement aux directives suivantes pose des risques de choc electrique, d'in-

cendie et/ou de blessure grave. Le terme , outil electrique _ dans tousles avertisse-

ments ci-apr#s se rapporte _ votre outil electrique _ alimentation sur secteur (avec ill)

ou par piles (sans ill).

CONSERVER CES DIRECTIVES

1) SI_CURITI_ -AIRE DE TRAVAIL

a) Maintenir I'aire de travail propre et bien eclairee. Les /ieux encombr6s ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner un outil electrique clans une atmosphere explosive, en

presence par exemple de poussieres, gaz ou liquides inflammables. Les outils 61ec-

triques peuvent engendrer des 6tincelles qui pourraient enflammer toute 6manation ou

poussibre ambiante.

c) Tenir les enfants, ou toute autre personne, eloignes pendant I'utilisation d'un outil

electrique. Toute distraction pourrait vous faire perdre la mMtrise de ce demier.

2) SI_CURITI_ - I_LECTRICITI_

a) La fiche electrique de I'outil dolt correspondre a la prise murale. Ne jamais

modifier la fiche en aucune faFon. Ne jamais utiliser de fiche d'adaptation avec un

outil electrique mis a la terre. L'utilisation de fiches d'origine et de prises appropri6es

r6duira les risques de choc 61ectrique.

b) Eviter tout contact corporel avec des elements mis a la terre comme tuyaux,

radiateurs, cuisinieres ou refrigerateurs. Les risques de choc 6/ectrique augmentent

Iorsque le corps est mis a la terre.

c) Ne pas exposer les outils electriques a la pluie ou a I'humidite. Toute p6n6tration d'un

outi161ectrique par un liquide augmente les risques de choc 61ectrique.

d) Ne pas utiliser le cordon de faFon abusive. Ne jamais utiliser le cordon pour trans-

porter, tirer ou debrancher un outil electrique. Proteger le cordon de la chaleur, de

I'huile et de tout bord tranchant ou piece mobile. Les cordons endommag6s ou

emm61#s augmentent les risques de choc #lectrique. Remplacer ou faire r#parer tout cor-

don endommag#. S'assurer que la rallonge est en bon #tat. N'utiliser que des rallonges

trifilaires munies de fiches tripolaires et des prises tripolaires acceptant la fiche de I'outil.

e) Lors de I'utilisation d'un outil electrique a I'exterieur, n'utiliser que des rallonges

conFues pour I'exterieur. L'utilisation d'une rallonge con_ue pour I'ext#rieur r#duit les

risques de choc #lectrique. En cas d'utilisation d'une rallonge, s'assurer que les valeurs

nominales de la rallonge utilis#e correspondent bien a celles de I'outil alimentS. L'usage

d'une rallonge de calibre insuffisant causera une chute de tension entrafnant perte de

puissance et surchauffe. Le tableau ci-dessous illustre les calibres a utiliser selon la

Iongueur de rallonge et I'intensit# nominale indiqu#e sur la plaque signal#tique. En cas de

doutes, utiliser le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter

de courant.

Calibre minimal des cordons de rallonge

Longueur totale du cordon en meters

De 0 & 7 De 7 & 15 De 15 & 30 De 30 & 45

De 0 & 7 De 7 & 15 De 15 & 39 De 30 & 45

Tension

120 V

240 V

Intensit6 (A)

Au Au

moins plus

0 6 18

6 10 18

10 12 16

12 16 14

3) SI_CURITI_ PERSONNELLE

Calibre moyen de fil

16 16 14

16 14 12

12 Non recommand6

Rester vigilant en tout temps et faire preuve de jugement pendant I'utilisation

d'un outil electrique. Ne pas utiliser d'outil electrique en cas de fatigue ou sous

I'influence de drogues, d'alcool ou de medicaments. Tout moment d'inattention

pendant I'utilisation d'un outil _lectrique pose des risques de blessure grave.

b) Utiliser le materiel de securite approprie. Toujours porter des lunettes de protection.

Le fait de porter un masque anti-poussibres, des chaussures antid_rapantes, un casque

de s#curit# ou des protecteurs auditifs Iorsque la situation le requiert r#duira les risques de

blessure.

c) Eviter tout demarrage accidenteL S'assurer que I'interrupteur est en position

d'arr6t avant tout branchement. Transporter un outil le doigt sur I'interrupteur ou

brancher un outil #lectrique alors que I'interrupteur est en position de marche invite les

accidents.

d) Retirer toute cle de reglage avant de demarrer I'outil. Une cl_ laiss_e sur une pibce

rotative d'un outil #lectrique pose des risques de blessure.

e) Ne pas effectuer de travaux hors de portee. Les pieds doivent rester bien ancres au

sol afin de maintenir son equilibre en tout temps. Cela permet de mieux maftriser I'outil

#lectrique dans les situations impr#vues.

f) Porter des v6tements appropries. Ne pas porter de v6tements amples ni de bijoux.

Maintenir cheveux, v6tements et gants eloignes des pieces mobiles. V#tements

amples, bijoux ou cheveux longs risquent de rester coinc_s dans ces pibces mobiles.

Prendre des precautions autour des #vents car ils recouvrent des pibces mobiles.

g) Lorsque un dispositif de connexion a un systeme de depoussierage ou d'elimina-

tion est fourni, s'assurer qu'il est connecte et utilise correctement. L'uti/isationde ces

dispositifs peut r_duire les risques engendr_s par les poussibres.

4) UTILISATION ET ENTRETIEN DES OUTILS #LECTRIQUES

a) Ne pas forcer un outil electrique. Utiliser I'outil approprie au travail en cours. L'outil

appropri# effectuera un meilleur travail, de fa_on plus s_re eta la vitesse pour laquelle il a

_t_ con_u.

b) Ne pas utiliser un outil electrique dont I'interrupteur est defectueux. Tout appareil

dont I'interrupteur est d#fectueux est dangereux et doff 6tre r#par#.

c) Debrancher la fiche du secteur et/ou le bloc-piles de I'outil electrique avant de faire

tout reglage ou changement d'accessoire, ou avant de ranger ce dernier. Ces

mesures preventives r#duisent les risques de d#marrage accidentel de I'appareil.

d) Apres usage, ranger les outils electriques hors de la portee des enfants, et ne per-

mettre a aucune personne n'etant pas familiere avec un outil electrique (ou son

manuel d'instruction) d'utiliser ce dernier. Les outi/s peuvent #tre dangereux entre/es

mains des novices.

e) Entretenir les outils electriques. Verifier les pieces mobiles pour s'assurer qu'elles

sont bien alignees et tournent librement, qu'eiles sont en bon etat et ne sont affec-

tees d'aucune condition susceptible de nuire au bon fonctionnement de I'outil. En

cas de dommage, faire reparer I'outil electrique avant toute nouvelle utilisation. Bien

des accidents sont causes par des outils mal entretenus.

f) Maintenir tout outil de coupe bien aiguise et propre. Les outils de coupe bien

entretenus et affOt#s sont moins susceptibles de se coincer et sont plus faciles a contr61er.

g) Utiliser un outil electrique, ses accessoires, meches, etc., conformement aux

presentes directives et suivant la maniere prevue pour ce type particulier d'outil

electrique, en tenant compte des conditions de travail et du travail a effectuer.

L'utilisation d'un outil _lectrique pour toute operation autre que celle pour laquelle il a _t_

congu est dangereuse.

5) SERVICE

a) Faire entretenir les outils electriques par un reparateur qualifie en n'utilisant que

des pieces de rechange identiques. Cela permettra d'assurer I'int#grit# de Ibutil

#lectrique et la s#curit# de I'utilisateur.

Directives de s_curit_ suppl_mentaires pour les

marteaux-piqueurs a percussion

• Tenir I'outil par sa surface de prise isolee clans une situation ob I'outil de coupe peut

entrer en contact avec un c#blage cache ou avec son propre cordon d'alimentation.

Tout contact avec un fil _ sous tension _,mettra _ sous tension _,les pibces m_talliques de

Ibutil et causera un choc #lectrique a I'op#rateur de Ibutil.

S'assurer que le mat#riau pem# ne cache pas de conduite #lectrique ou de gaz et que leur

emplacement a#t# v#rifi# avec les entreprises de services publiques.

• Porter des protecteurs d'oreilles. Une exposition au bruit peut entrafner une perte auditive.

• Utiliser les poignees auxiliaires fournies avec I'outil. Une perte de maftrise de Ibutil peut

entrafner des blessures.

Tenir fermement Ibutil en tout temps. Ne pas tenter de faire fonctionner cet outil sans le tenir

des deux mains. Faire fonctionner cet outil d'une seule main risque de provoquer la perte de

mMtrise de Ibutil. IIpeut aussi 6tre dangereux de percer ou de tomber sur des mat#riaux durs

comme une barre d'armature. Bien serrer la poign#e lat#rale avant d'utiliser Ibutil.

• Porter des lunettes de securite ou une protection oculaire. Les operations de percussion

peuvent projeter les copeaux. Les particules projet#es peuvent provoquer un

endommagement irreversible des yeux. Porter un masque antipoussibres ou un appareil

respiratoire. La plupart des applications peuvent demander I'utilisation d'un dispositif de

protection des oreilles.

• Tenir fermement I'outil en tout temps. Ne pas tenter de faire fonctionner cet outil sans

le tenir des deux mains, fl est recommand# d'utiliser en tout temps la poign#e lat#rale. Faire

fonctionner cet outil d'une seule main risque de provoquer la perte de maftrise de Ibutil. fl

peut aussi 6tre dangereux de percer ou de tomber sur des mat#riaux durs comme une barre

d'armature.

• Ne pas faire fonctionner cet outil durant de Iongues periodes. Les vibrations caus_es

par la percussion du marteau peut 6tre nuisible pour vos mains et vos bras. Utiliser des gants

pour amortir davantage les vibrations et limiter I'exposition a Ibutil par de fr#quentes p#riodes

de repos.

Page is loading ...

DeWalt SDS max D25890 Owner's manual

Brand: DeWalt

Model: SDS max D25890

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: DeWalt SDS max D25890 Le manuel du propriétaire
español: DeWalt SDS max D25890 El manual del propietario

DeWalt SDS max D25890 Owner's manual

This manual is also suitable for

DeWalt SDS max D25890 Owner's manual

in other languages

Related papers

Other documents