Coyote C1P28 Installation guide

C1P28
Coyote
Brand
Coyote
Model
C1P28
Category
Barbecues & grills
Type
Installation guide

This manual is also suitable for


   
   
P2
26 1/4"
1P28
31"
28"
TC1P28
1P28
When using a Coyote insulated jacket, you will want to build your island to the jackets Cutout and Overall Dimensions
listed above (detailed on 2nd page). Once the jacket is installed, the grill will rest on/inside the insulated jacket
23"
27"
16 1/2"
Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety
requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.
FRONT VIEW
REAR VIEW
SIDE VIEW
C1P28
INSTALL GUIDE
SIDE VIEW
17 3/4"
30"
24 3/4"
17 1/4"
27 1/4"
22 1/2"
26 1/4"
28"
23"
27"
31"
16 1/2"
23"
30"

BTU/HR Amps Electrical Requirements
1P28
8,000
5
120V 60Hz Grounded Plug
DIMENSIONAL RENDERINGS
www.coyoteoutdoor.com
C1P28 INSTALL GUIDE
16
1
/2"
OPENING
HEIGHT
DOORS / DRAWERS
OPENING WIDTH
23"
OPENING
DEPTH
OPENING
HEIGHT
GRILL
OPENING
GRILL
OVERHANG
TOP VIEW
26 1/4"
"
OPENING WIDTH
1
1
/2"
OPENING
HEIGHT
DOORS / DRAWERS
OPENING WIDTH
OPENING
DEPTH
OPENING
HEIGHT
12"
LINER
OPENING
1 3/4"
JACKET
OVERHANG
TOP VIEW
OPENING WIDTH
12"
NON-COMBUSTIBLE CONSTRUCTION
Insulated Jacket NOT Required
FRONT VIEW
FRONT VIEW
1
1
/2" MIN
INCLUDING
COUNTERTOP
Combustible material can not be within 12" of the grills frame
This applies to all directions - horizontal & vertical
Shaded area above on "TOP VIEW" illustrates the 12" minimum
requirement (not to scale for rendering purposes)
The grill is designed to hang from the counter top with no support
underneath
Minimum rear clearance for the hood to open is 2 1/4"
If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
12"
If using combustible material within 12"of the grill frame, you MUST use
the corresponding Coyote Insulated Jacket
Using a insulated jacket, does not waive any other standard installation
procedure (ventilation, connections, etc)
The jacket is designed to hang from the counter top with no support
underneath
Minimum clearance for hood to open is 2"
If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
Ventilation Requirements:
Regardless if you are using a combustible or non-combustible building material, you must include at least two vents but
optimally 4 vents within the island.
These vents must be at least 20 sq. in. each and allow fresh air to move from the grill cabinet to the exterior environment.
Do not locate the two vents on the same wall of the island. Cross ventilation is key to allow any excess heat or trapped gas
to dissipate.
1
1
/4"
May vary
per install
1
1
/2"
22
1
/2"
1
1
/2" MIN
COMBUSTIBLE CONSTRUCTION
Insulated Jacket Required - Model # CJAKTC1P28
1 3/4"
17 1/4"
INCLUDING
COUNTERTOP
27
1
/4"
May Vary
Per Install
6"
2
1
/2"
2"
E
CONNECTION
E
3
1
/2"
3
1
/2"
E
Elec.
CONNECTION
3
1
/2"
3
1
/2"
Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety
requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.
Elec.
E
  • Page 1 1
  • Page 2 2

Coyote C1P28 Installation guide

C1P28
Coyote
Brand
Coyote
Model
C1P28
Category
Barbecues & grills
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents