ADURO SB10 MANUAL

1) Pairs with any Bluetooth enabled mobile device.

 • Answer,endandrejectcallfromtheheadset

 • PushButtonRedial

 • VoiceRecognitionDial

 • StereoSurroundMusic

 • RemotecontrolbuttonsontheheadsetforPause/Play/

 sametime.Allyouneedtodoissimplyrepeatthepairingprocess

 fortheseconddeviceandmanuallyreconnectfromthe

 firstdevice.

6)VoicepromptcomeswithfivestatusalertsinEnglish.Poweron,

 poweroff,pairing,pairingcompleted,incomingcall(foriPhone,

FEATURES

FEATURES

 youwilldirectlyheartheringtoneinsteadof“incomingcall”).

Note:Eventhoughthepaireddeviceandheadsetsupportthesame

Bluetoothprofiles,thefunctionsmaybedifferentduetothe

specificationdifferenceofthe-paireddevices.

1.

3.

4.

CHARGING

• ChargingtheAduroSB10forthefirsttime:

 Pleasebesuretochargeafull3hoursbefore

initial use

• Whenyouhear3warningtonesandatthesametimethered

 lightblinkstwotimes,itmeansthatbatteryhasalmostrunout.

Charging the battery with Micro USB cable

• Step2:ConnectchargingcabletotheMicroUSBchargingport

 ofheadset.

• Whentheredlightison,theheadsetisincharging.

• Whenthelightturnsblue,theheadsetisfullycharged.

• Ittakesabout3hourstochargetheheadsetfully.

Note:Whenyouhavechargingcablepluggedin,pleaseturnoffthedevice

HOWTOUSE

HOWTOUSE

Switching on / off headset

Function Operation LED Indicator Voice Prompt

Switchon  BlueLightblinks3times PowerOn

Switchoff  RedLightblinks3times PowerOff

PresstheMFBbutton

release it till the red

LEDison

Pairing the headset with Bluetooth Howtoenterpairingmode

Function Operation LED Indicator Voice Prompt

EnterPairing RedandBlueLEDs Pairing

mode blink alternately

Make sure the headset

isoff.Pressandhold

MFBbuttonfor6

seconds,andreleaseit

till the red and blue

Pairing the headset with Bluetooth mobile phone

PleasemakesureyourmobiledeviceisBluetoothcompatible

Note:Specificpairingproceduresmayvarywithdifferentmobile

devices.Pleaserefertoyourmobiledevice’smanualforfurther

information.Stepsasfollows:

• Pleasekeeptheheadsetandmobilephoneintherangeof3feet

surefeatureisturnedon.Clickon“Scan”.SelectAduroSB10from

the list.

• Ifprompted,enterpasswordorPINNo:“0000”,andpress“Yes” or

“Confirm”.(dependingonyourdevice)

• Aftersuccessfulpairing,select“Aduro SB10” in the Bluetooth

 devicelist,andpress“connect”.

repeatthepairingprocessagain

Re-connecting to a Bluetooth device

Automaticconnecting

 Everytimetheheadsetisswitchedon,itwillconnecttolast

 connecteddeviceautomatically,ofcoursethesourcedevice

Function Status of headset Operation

Voicedial Standbymode

Redial last Standby mode

number

Volumeup Conversation

mode

PressandholdMFBbuttonfor1second,releaseit

untilyouhearindicatorsound,thensaythename

you want to call.

 calling

 Reject Ringing

 calling

Shortpress-key

ShortpressMFB

PressandholdMFBbuttonfor1second,and

release until you hear indicator sound

•Notallthemobilephonessupportallthefunctionslistedabove.Pleaserefertotheinstructionofyourmobilephone

Function Status of headset Operation

Pause Playingmusic    