Analog way VIO 4K Quick start guide

Brand: Analog way

Model: VIO 4K

Type: Quick start guide

Analog Way VIO 4K, your newly acquired video processing toolbox, empowers you with cutting-edge image processing and conversion capabilities. Effortlessly control and configure VIO 4K via its intuitive front panel interface or the web-based remote control software. Create stunning visuals with advanced color adjustments, crop and scale images, and apply a variety of effects. Experience seamless transitions between sources and utilize the built-in frame feature for dynamic content display.

VIO 4K - Ref. V701

QUICK START GUIDE

Thank you for choosing Analog Way and the VIO 4K. By following these simple steps, you will be able to set up and

use within minutes your brand new Video Processing Tool Box. Discover the VIO 4K capabilies and intuive interface

designed to meet all needs in terms of image processing and conversion.

• 1 x VIO 4K (V701)

• 1 x Power supply cord

• 1 x Ethernet cross cable (for device control)

• 1 x MCO 5 pin connector

• 1 x Web-based Remote Control Soware included and hosted on the device

• 1 x Rack mount kit (the parts are stowed in the packaging foam)

• 1 x User manual*

• 1 x Quick start guide*

* The User Manual and the Quick Start Guide are also available on www.analogway.com

You can quickly control and congure your new VIO 4K unit from the VIO 4K unit itself, via the front panel buons and

the front panel menu tree.

CAUTION!

Addional support such as

the rear rack or slide rails is

strongly recommended for all

mounng applicaons.

Go to our website to register your product(s)

and be noed about new rmware updates:

hp://bit.ly/AW-Register

• Rotate the front panel control knob and press the

ENTER and EXIT/MENU buons to navigate through

the menus and adjust your setup.

• Select the input to display on the output by choosing

the corresponding INPUT SELECTION buon, or use

BLACK to output to the screen background color.

1. Set up your outputs and outputs plugs

2. Set up your inputs and inputs plugs

3. Import frames and manage frame features

4. Set up the audio and manage A/V mapping

5. Access technical support informaon and device

control services

6. Create custom formats, manage transions, adjust

the screen background color …

7. Manage the device sengs and control funcons like

LAN and the Safe Input Select feature

8. Adjust the LED wall area of interest (AOI) and set up

the view

9. Save and load preset conguraons

10. Check your current VIO 4K conguraon

QUICK SETUP & OPERATION

WHAT’S IN THE BOX

Front panel menus on LCD display

1 2

• Switch ON the unit to access the front panel menu tree:

Scroll knob:

Navigate the menu tree

(menus, sengs and

status pages)

Slot for oponal audio card*:

XLR audio expansion interface

or Dante audio expansion interface

(Q2 2017)

Slot for oponal video card 1*:

supporng input and output

formats up to 4K@60Hz 4:4:4

Slot for oponal video card 2*:

supporng input and output formats

up to 4K@60Hz 4:4:4

Funcons:

Pan Zoom: Display the view sengs menu

Audio: Display the audio sengs menu

Test Paern: Display the test paern menu

Monitor: Access the front panel monitoring menu

Standby:

Set the device to standby

(or wake up the device when in

standby mode by holding the

buon for several seconds)

Line In:

Audio input plug

Headphone:

Prelisten to audio inputs

and outputs

USB:

Host: USB host

interface (USB key)

Device: USB device

interface (other USB)

Input 7/HDMI:

HDMI input up to

4K@30Hz 4:4:4

LCD display:

Navigate the menu

tree and monitor input

sources and outputs

Input selecon:

#1 to #9: Select the input to

display on the output

Black/Color: Output to black

(display no input)

Control:

Exit/Menu: Return to

previous menu or exit

without saving

Enter: Validate a menu or

conrm the new sengs

Power supply:

Internal, universal, automac,

100-240 VAC 3,2A 50/60Hz;

120W (UL, CSA, GS, CE),

AC Main switch with Fuse

(cartridge 5x20 4A Fast 250VAC)

Inputs:

- DisplayPort up to 4K@30Hz

- HDMI up to 4K@30Hz

- Universal Analog

- Video Opcal SFP Module cage

- SDI and SDI loop-through

- DVI Dual-Link up to 2560x1600@60Hz

Outputs:

- DisplayPort up to 4K@30Hz

- HMDI up to 4K@30Hz

- Universal Analog

- Video Opcal SFP Module cage

- SDI (Compliant Level A & B)

- DVI Dual-Link up to 2560x1600@60Hz

- DVI, HDMI & HD15 output plugs

available as video loop-through

Genlock:

Genlock input connector

Tally:

- 2 x GPO

- 1 x ON/OFF

RS232 port:

Serial interface connector

for 3rd party controllers

Connecvity:

Ethernet: LAN interface connector

Device sync: Dual device synchronizaon

Shortcut:

Freeze: Freeze/unfreeze

the output

Quick Frame: Acvate

the Quick Frame funcon

CAUTION:

Avoid disconnecng the power source (AC input) unl

the unit is in standby mode. Failure to do so could

result in memory data corrupon.

* See the VIO 4K User Manual for more details

VIO 4K - REF. V701 / FRONT & REAR PANELS DESCRIPTION

OPERATION OVERVIEW

AUDIO MANAGEMENT

VIEW SETTINGS

Set up the "View" of your inputs in the screen:

• Use Pan and Zoom to size and posion the view in your

screen.

• Apply a color Eect or enable a Flip movement on the view

of a live input.

• S a v e your view sengs and recall them later on any input

via the View Bank.

• Create presets of your input and view sengs to load them

readily at runme.

Audio in & out sengs:

Set up the audio independently of the video content:

• Manage up to 4 embedded channel pairs per input/output.

• Congure the auxiliary audio for each audio pair.

• Set up an audio prelist and prelisten to your content on the

headphone output.

A/V mapping:

Select an A/V mapping mode to map an audio stream to the

output (embedded audio by A/V mapping):

• Follow mapping mode: The audio content of the output will

follow the A/V mapping of the input selected at runme.

• Direct roung mode: The audio content of the output is

set once and for all, independently of the input selected at

runme.

Enter the OUTPUTS menu to set up your output(s).

Output format and rate:

• Choose the format and rate generaon mode and then adjust

the format sengs accordingly.

• Go to the CUSTOMIZE menu and create your own custom

format when the required format is not available in the list of

predened output formats.

Area of interest:

Adjust the acve area of your display in the output format.

Image correcons:

• Adjust the gamma correcon of your output image (especially

useful if seng up a LED Wall).

• Use the advanced color adjustments like color temperature,

brightness and contrast to truly ne-tune your output image.

• Enter the INPUTS menu to have an overview of all your inputs

and their status.

• Select AUTOSET ALL to launch the automac detecon of all

plugs of all inputs.

Input sengs:

• Select an input to set up the input individually.

• Enter the Plug Sengs menu to select the type of input signal

by plug, enable or disable HDCP negoaon on the sources

connected to the input plug, and manage the plug’s preferred

EDID formats.

• Select the Image Sengs menu to opmize the input image

signal and correct for the image aspect rao and size.

BUTTON COLOR USAGE

OUTPUT SETUP INPUT SETUP

Solid red:

Acve input, funcon or shortcut

Solid green:

OFF:

Blinking:

Available input, funcon or shortcut

Not available input, funcon or shortcut

Device inializing

SOURCE CONTROL

• Freeze the output and Monitor inputs and outputs on the

front panel LCD display.

• Customize the Transion Type and the Transion Duraon to

smoothly transion between sources.

• Use Frames to transion through frame or acvate the Quick

Frame funcon to quickly display a frame on the output.

• Select the input to display on the output by choosing the

corresponding INPUT SELECTION buon.

TIP: Try to use nave resoluon of your screens/projectors to

avoid addional scaling.

TIP: Crop the image and use a display aspect rao to correct

for the image aspect rao aer crop.

TIP: Use Follow mapping mode to map audio streams and

input plugs and set up the A/V mapping of your inputs.

TIP: Enable the Safe Input Select front panel control to lock

the selecon of inputs without signal.

For more details on features, funcons and procedures, please refer to the VIO 4K User Manual or visit our website:

www.analogway.com

15-SEP-2020

V701-QSG

Code : 140166

This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults resulng

from user negligence, special modicaons, electrical surges, abuse (drop/crush), and/or other unusual damage. In the unlikely

event of a malfuncon, please contact your local Analog Way oce for service.

The Web RCS remote control soware comes embedded into your VIO 4K unit and you simply need a web browser and a standard

LAN network (or an Ethernet over USB connecon) to connect.

Connecng to the Web RCS (LAN)*

- Download AW Browser on www.analogway.com to use the

Web RCS.

To connect to the Web RCS of your VIO 4K using a standard LAN

network, you rst need to connect your computer to the VIO 4K

using the provided Ethernet cable.

Open AW Browser and enter the IP address of the VIO 4K

(displayed in the front panel LCD screen).

The Web RCS connecon should start.

Manual setup: If your computer is not set to DHCP (automac

IP detecon) mode, you need to setup LAN manually to be able

to connect:

(1) Set up your VIO 4K

1. Go to Control > Connecon > LAN Setup on the front panel

menu tree

2. Disable the Obtain IP via DHCP funconality

3. Edit the LAN sengs of your VIO 4K unit, for example:

• IP address: 192.168.2.140

You can use the Web RCS interface to remotely control and congure your VIO 4K unit from a PC or tablet via LAN or via USB.

SETUP MENU

EDIT MENU

WARRANTY AND SERVICE

WEB RCS INTERFACE

GOING FURTHER WITH THE VIO 4K

• Set up your outputs and create

custom formats

• Set up your inputs and input plugs

• Set up the audio and manage A/V

mapping

• Import frames and manage frame

features

• Access technical support

informaon

• Manage the device sengs and

control funcons

Web RCS interface loaded into your web browser

Put everything together in the screen:

• Resize and posion the view

• Save and recall view sengs

• Save and recall presets

• Monitor input sources

• Select inputs

• Manage transions

• Freeze the output

• Display a Quick Frame

• ...

• Gateway: 192.168.2.160 • Netmask: 255.255.255.0

(2) Set up the LAN adaptor of your PC

1. Open your LAN adaptor sengs

2. Assign an IP address to your computer on the same network

and subnet as your VIO 4K, for example:

• IP address: 192.168.2.16 • Gateway: 192.168.2.150

• Netmask: 255.255.255.0

You should be able to connect now.

Once the connecon has been established, the Web RCS inter-

face will load into your web browser. The 2 icons at the boom

right corner of the screen indicate that the Web RCS is ready to

be used:

• V701: Turns green when connected

• Sync OK: Turns green when the Web RCS has nished syn-

chronizing

If you are having trouble synchronizing, try clearing the cache

and refreshing the page (CTRL+F5 shortcut on most browsers).

* Please see the User Manual for informaon on how to connect via USB.

4. Select Apply to save and apply the new sengs.

Analog way VIO 4K Quick start guide

Analog way VIO 4K Quick start guide

Analog way VIO 4K Quick start guide

Related papers

Other documents