Page 1 of 8
REF : OCEAVT30CM
TABLE FAN
User manual
This appliance is intended for domestic household
use only and should not be used for any other
purpose or in any other application, such as for
non-domestic use or in a commercial environment.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the haz-
ards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
For the details concerning the method of cleaning,
please see section “Cleaning and maintenance” on
page 7.
Warning! After assembly, it's strictly forbidden to
remove the protective guards during maintenance
or cleaning.
Never use the fan without the guards in place.
Regarding the method on how to assembly and
Read all instructions before using this appliance
and keep them for future reference.
•
•
•
•
•
•
Page 2 of 8
IMPORTANT SAFETY INSTRUCTIONS
Page 3 of 8
Do not use outdoors.
Make sure the appliance is placed on a stable
surface when used.
Never insert fingers, pencils or any other objects
through the guards when the fan is operating.
Turn off and unplug the fan from the mains socket
when not in use, before moving or cleaning.
Do not unplug the fan by pulling on the cord.
Grasp the plug to pull to disconnect.
Do not let hair, net curtains, tablecloths or loose
clothing come into contact with the moving parts of
the fan as it may cause damage or injuries.
Do not use this fan near a window that may have
condensation on it.
Do not use this fan with any external semi-conductor
speed controller.
Do not use this fan in areas where flammable
liquids are used or stored.
Do not let the power cord hang over the edge of a
table or counter top.
Do not let the power cord touch any hot surface.
Do not use the appliance for other than its intend-
ed use as laid out in these instructions.
Do not try to repair this fan yourself. There is no
user serviceable parts inside and all servicing and
•
•
•
•
•
•
•
•
•
•
•
•
•
how to fix the fan with screws, refer to the section
“ASSEMBLY”.
•
•
repair must be undertaken by the manufacturer, its
after-sales service or a qualified service agent in
order to avoid a hazard.
•
Page 4 of 8
CAUTION:
Base assembly
Rear guard assembly
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Front guard
Retaining nut
Fan blade
Locking nut
Rear guard
Motor spindle
Oscillation knob
Adjusting screw
Control buttons
Base
Securing screws
DO NOT insert the mains plug into the mains socket until the fan has been completely assembled. Never
operate the fan with a cracked or damaged fan blade.
Page 5 of 8
PARTS
Fan blade assembly
ASSEMBLY
Unscrew the retaining nut from the motor spindle clockwise. Unscrew
the locking nut from the motor spindle anticlockwise.
Position the rear guard onto the motor housing; make sure the handle
on the rear guard is pointing upwards.
Insert the locking nut and turn it clockwise to lock the rear guard into
position.
Remove the supplied 2 screws from the base.
Insert the fan body into the hole of the base and then press it into the base until it clicks in position.
Fix the base onto the fan body by tightening the supplied screws.
1.
2.
3.
Slide the fan blade onto the motor spindle, making sure the motor
spindle is fully seated into the blade groove.
Screw the retaining nut anticlockwise to tighten the fan blade to the
motor spindle.
Front guard assembly
Remove the small securing screw and nut from the front guard.
Attention!
The hook of the front guard must be at the top.
Make sure that the holes in both guards are aligned and fasten
them securely by using the provided screw and nut. Once the guard
is in position fasten the clips to finally secure both guards.
Locking nut
Always turn off and unplug the fan from the mains socket before cleaning.
Once the fan guard was assembled, it’s forbidden to take off the guards.
Clean the fan with a slightly damp cloth, and then dry it.
Do not immerse the motor housing in water or any other liquid.
Do not use chemical or abrasive cleaner.
Storage
If stored disassembled, it is recommended to use the original (or appropriately sized) box.
If stored assembled or partially assembled, protect the fan head from dust.
•
•
When not in use keep the fan in a safe, dry location.
Ratings: 220-240V~, 50Hz 40W
a.
b.
c.
0= Off 1= Low speed 2=Medium speed 3=High speed
Place the fan on a stable, level surface.
Plug the fan in the mains socket.
Press the 1, 2 or 3 control button to select the desired speed. To turn off the fan, press the 0 control button.
1.
2.
3.
To make the fan oscillate, push down the oscillation knob located on the top of the motor housing and
the fan will oscillate from side to side.
To stop the fan from oscillating, lift up the oscillation knob.
Tilting Adjustment
The airflow can be adjusted upward or downward.
Hold the base and slightly loosen the adjusting screw by turning it anticlockwise.
Tilt the fan to the desired wind direction (i.e. either upward or downward).
Tighten the adjusting screw by turning it clockwise.
4.
5.
Page 6 of 8
OPERATION
CLEANING AND MAINTENANCE
SPECIFICATIONS
Technical informations
Ref: OCEAVT30CM
Model: FT30A
Description Symbol
F 19.53
35
0.56
52.049
2.45
-
P
SV
C
IEC 60879:1986 (corr. 1992)
AMC
123 quai Jules Guesde
94400 VITRY SUR SEINE
France
L
WA
P
SB
Value Unit
Maximum fan flow rate
Power
Service value
Fan sound power level
Standby power consumption
Maximum air velocity
Service value measurement standard
For more information, please contact
m³/min
(m³/min)/W
dB(A)
W
W
m/s
Page 7 of 8
DISPOSAL
IMPORTED BY
As a responsible retailer we care about the environment.
As such we urge you to follow the correct disposal procedure for the appliance and packaging
materials and if applicable, batteries. This will help conserve natural resources and ensure that it
is recycled in a manner that protects health and the environment.
You must dispose of this appliance and its packaging according to local laws and regulations.
Because this appliance contains electronic components and may contain batteries, the appliance
and its accessories must be disposed of separately from household waste when the appliance
reaches its end of life.
Contact your local authority to learn about disposal and recycling.
The appliance and if applicable, batteries should be taken to your local collection point for
recycling. Some collection points accept appliance free of charge.
We apologise for any inconvenience caused by minor inconsistencies in these instructions, which
may occur as a result of product improvement and development.
amc
123 quai Jules Guesde
94400 Vitry sur seine
France
LOT#:
amc112018
Page 8 of 8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Rasonic RLF-9KITD User manual
-
-
Proline MINI R User manual
-
PRO ELEC PEL01921-EU Operating instructions
-
Matsui MAT-PFS16 Instruction book
-
Carlton PF16SS User manual
-
Continental Platinum CP49518 User manual
-
PRO ELEC PEL01935 Operating instructions
-
PRO ELEC PEL01936-EU Operating instructions
-
Mellerware 3 5 9 5 0 1 7 0 W User manual
