3SIXT DV123SANC-3S User manual

Brand: 3SIXT

Model: DV123SANC-3S

Type: User manual

USER GUIDE

HD SPORTS

ACTION CAMERA

with LCD Screen

IMPORTANT SAFETY INFORMATION

Please read the instructions carefully before using this

camera for proper and safe operation.

• Please check the video camera operates normally

before use.

• Do not expose the video camera to direct sunlight, or point

its lens to sunlight - the image sensor may get damaged.

• Take good care of the video camera and prevent water or

sand particles from entering the housing when it is used

on the beach or in water. Water, sand particles, dust or

composites containing salt may damage.

• Keep the video camera free of dust and chemical materials.

Place it in a cool, dry and well ventilated environment. Do

not place the video camera in a high temperature, moist or

dusty place.

• If dust or dirt is accumulated on the video camera or on its

lens - use a so, clean and dry cloth to wipe away gently.

• Do not use a cloth to wipe sand particles. Blow them away

gently then wipe the camera gently with a cloth suitable for

optical devices.

• Do not use solvents to clean the video camera.

• Do not touch the lens surface with your ﬁngers.

• This camera supports a MicroSD Memory Card (up to 32GB).

Please insert the MicroSD Memory card before use. SD

Memory cards are not included and need to be purchased

separately.

• Please back up data stored on the memory card.

• Memory cards are manufactured from precise electronic

components. Data may be lost or damaged under the

following circumstances:

• The memory card is bent, dropped or damaged.

• Place it under high temperature or moist environment or

expose to sunshine directly.

• Electrostatic or electromagnetic ﬁeld exists around the

memory card.

• This memory card is taken out or power supply is

interrupted when this video camera or computer is

connected to the memory card (i.e. during reading,

writing and formaing).

• Touching the metal contact surface of the memory card

with your ﬁngers or metallic materials.

We recommend cards for maximum

performance.

For more info, videos and support,

visit www.3sixtgear.com/support

前壳�印�色

GETTING TO KNOW YOUR CAMERA

6 7

2 3

前壳�印�色

Micro SD Memory Card Slot

Reset Buon

USB Interface

Power Buon

Shuer Buon

Mode Switch:

Photo, Video, Vehicle Mounted

Strap Connector

Microphone

Power Indicator/Busy LED Light

Charge Indicator LED Light

LCD TFT Screen

Lens

1 7

2 8

3 9

410

511

612

SYSTEM REQUIREMENTS

To be able to download videos and photos to your computer,

you will need the following minimum conﬁguration including

and internet connection, and Adobe® Flash® Player:

Windows

Microso® Windows XP with Service Pack 3, Windows Vista with

Service Pack 1 or Windows 7

Pentium® 4 processor (or above)

1 GB of RAM, 250 MB available hard disk space

16-bit colour monitor, 1024 X 768 recommended screen resolution

CD-ROM Drive

QuickTime® 6 or higher

Microso® Internet Explorer 7 or higher

Windows Media Player 10 or higher

DirectX 9 or higher

Macintosh

Intel processor running Mac OS X v10.5.x or later

1 GB RAM, 250 MB available hard disk space

1024 x 768 or higher-resolution monitor

QuickTime® 6 or higher

USAGE

Charging the built-in lithium baery

Make sure the built-in lithium

baery has been fully

charged before using your

camera. To charge the

baery:

• Power OFF the camera.

• Connect your camera from the USB

Interface 3 using the mini USB cable

provided to a PC.

• The ‘Charge’ LED light 10 lights up red

indicating that your camera is in ‘Charge’

mode. The LED switches o when your

camera is fully charged.

前壳�印�色

MicroSD Memory Card

Make sure a MicroSD Memory card has been properly inserted

into your camera (MicroSD Memory card not included).

To properly insert the MicroSD Card:

• Power OFF the camera.

• Insert the MicroSD Card into the

MicroSD Card slot 1 in the direction

as shown on the camera (see SD icon

by the MicroSD card slot).

• Gently press the MicroSD Card until you

hear a slight clicking sound. This indicates

the memory card has been inserted correctly.

• To remove the card, gently press on the edge of the card to

release it and pull the card out.

• If the card is inserted or removed while the camera’s power

is on, it may damage the card and/or any stored data.

Always conﬁrm that the power is o before inserting the

card into the camera.

Indicator Lights

When the camera is busy (such as recording, taking photos, or

automatic o-screen), the ‘Busy’ light 9 will be on.

A static ‘Charge’ light 10 indicates the camera is charging.

前壳�印�色

Power ON/Power OFF

Power ON:

Press the POWER

buon 4 for 3 seconds -

the display screen

appears. The camera

is now ON.

Power OFF:

Press the POWER

buon once - the display

screen disappears.

The camera is now OFF.

Auto Power OFF:

When the camera is le idle for more than 5 minutes, the

camera will power OFF automatically to save energy.

Once the camera is automatically powered o, you can press

the POWER buon once to power on the camera.

NOTE: Aer 2 minutes of inactivity, the camera LCD screen

turns black to save energy. The red ‘Busy’ LED light 9 is on to

indicate that the camera is in standby mode. Simply press any

buon or touch the LCD screen to reactivate the camera.

Auto Power OFF due to low baery:

When the baery power is low, the LCD display screen will

display the ‘low power’ icon. When the indicator light turns red

and is ﬂickering, the camera will power OFF automatically.

前壳�印�色

GETTING TO KNOW THE LCD SCREEN

Function Mode

1.00

0/1234

00:12:18

Mode Picture Video Vehicle-Mounted

0/1234

or 00:12:18

Number of images

taken/number of images

to be taken

Indicated time remaining for recording

or Image resolution Video resolution: 720P or VGA

Memory card is inserted

Zoom In

Zoom Out

Shuer

Baery Power Status

Digital Zoom Status

Playback

Date & Time Seing

前壳�印�色

Playback Mode

Mode Picture Video Vehicle-Mounted

File type

Number of ﬁles in current folder

Current folder name

Preview ﬁles forward

Preview ﬁles back

Conﬁrm deletion of current ﬁle

Play current movie clip

Switch back to current function mode

Play forward

Play backward

Pause

USING THE FUNCTION MODES

Three modes are available:

Picture

Still images can be taken

Video

Video can be recorded

Vehicle-Mounted

Continuous video can be recorded

(one section every 5 minutes)

NOTE: Use the Mode Switch aer startup.

Picture Mode:

Switch the mode to ‘Picture’, press the Shuer Buon 5

or click the LCD centre once to take a photo.

Video Recording mode

Switch the mode to ‘Video’, press the shuer buon once or

click the LCD centre once to begin recording. Press the shuer

buon once again to stop recording. The camera will also stop

recording automatically when the memory card is full or the

baery is low.

Vehicle-Mounted mode:

Switch the mode to ‘Vehicle-Mounted’, press the shuer

buon or click the LCD centre once to begin recording.

A segment of recording will be saved every 5 minutes and

then the next segment of video will start to record. When the

storage card is full, the earliest segment of video will be deleted

to release the corresponding space for continuous recording.

Using the Playback Mode

Aer starting up and entering the preview screen, click the

playback icon at the lower right corner of the LCD screen

to switch to the playback mode:

To play a movie clip:

Click to pause playing, click to play forward,

and click to play backward.

To delete a movie clip:

Click to delete the current ﬁle and the YES to conﬁrm, or

click NO to cancel the request of deletion.

Connecting the camera to a computer

Use the supplied USB cable to connect

your camera to a computer.

For Windows OS users:

1. Power the camcorder ON.

2. The ﬁrst time you connect the

device to the computer you may

have to wait a few seconds until

the computer recognises the device. The ‘MSDC’ connection

icon displays on the LCD screen.

3. A window appears on your computer with a list of options,

select ‘Open folder to view ﬁles’ and click ‘OK’.

4. Open the DCIM folder and the folder inside to view the

media ﬁles.

5. Select the media and copy the ﬁles from this folder onto

your computer. Optionally, select the ﬁles and choose ‘Copy’

from the Edit menu. Then select a folder and choose ‘Paste’

from the Edit menu.

6. Do not disconnect the cable during transfer. Doing so will

cancel the transfer of ﬁles.

For Macintosh OS users:

1. Power the camcorder ON.

2. The ﬁrst time you connect the device to the computer

you may have to wait a few seconds until the computer

recognises the device. The ‘MSDC’ connection icon displays

on the LCD screen. The camera’s device icon appears on the

desktop.

3. Click on the device icon and open the DCIM folder and the

folder inside to view the media ﬁles.

4. Select the ﬁles and drag them onto your computer.

Optionally, select the ﬁles and choose ‘Copy’ from the

Finder’s Edit menu. Then select a folder and choose ‘Paste’

from the Edit menu.

5. Do not disconnect the cable during transfer. Doing so will

cancel the transfer of ﬁles.

USING THE INCLUDED ACCESSORIES

Waterproof Case

CAMERA IS SUBMERSIBLE

UP TO 2M IF CAMERA IS

CORRECTLY SEALED IN

WATERPROOF CASE

1. Insert a ﬁnger at

the half circle of the

clamp by prying the

clamp up away from

the case.

2. Before sealing the

case, inspect the

water sealing gasket to be sure it’s in good condition. You

can test the gasket by closing the case without inserting

the camera.

3. Submerse the case completely in a bowl of water for about a

minute. Remove the case from the water, dry o its exterior

with a towel and then open the case. If the entire interior is

dry, the case and gasket are safe for use under water.

4. There are just two buons required for recording video and

images: the Shuer, and the Power Buon.

5. Remember to put the Mode Switch in your desired recording

position before inserting the camera in the waterproof case.

There is no external buon for the Mode Switch.

CLAMP SHUTTER POWER

Handlebar Mount

1. The camera does not have a

standard tripod mount. For all the

accessories with a 1/4-20 screw,

the camera must be enclosed in

with the waterproof case or in the

included mounting adapter.

2. Turn the waterproof case (or

mounting adapter) clockwise

onto the 1/4-20 screw of the

handlebar clamp until secure.

3. Turn the Locking Wheel so it

applies pressure to the case to keep the connection secure.

4. Loosen the Bar Clamp Bolt until the screw can be pushed

90° upward.

5. The boom half of the Bar Clamp can be opened to allow

you to wrap the Handlebar Clamp around the actual

handlebar of your bicycle.

6. Aer positioning the Handlebar Clamp where you want it,

close up the boom half of the clamp and tighten the Bar

Clamp Bolt.

7. Loosen the Tilt Knob, to adjust for the proper aiming angle;

then tighten the knob.

Panning adjustments can be made by loosening the Locking

Wheel, adjust the pan angle; then tighten the wheel.

1/4-20

SCREW

BAR CLAMP

BOLTS

BAR

CLAMP

LOCKING

WHEEL

TILT

KNOB

Helmet Mount

1. Insert the free end of the

Helmet Strap through one

of the slots in the base of

the Helmet Mount.

2. Thread the same end

in to the helmet’s vent

and then back up to the

Helmet Mount through

another vent. Then insert

the strap through the

other side of the Helmet

Mount. Then insert the strap back through the helmet vent.

3. You should have now both ends of the strap inside the

helmet. Take both ends of the strap and pull to tighten and

then aach together with the Velcro.

4. Turn the Waterproof Case (or Mounting Adapter) onto the 1/4-

20 screw of the Helmet Mount until secured.

5. Turn the Locking Wheel so it applies pressure to the case to

keep the connection secure.

6. Loosen the Tilt Knob, to adjust for the proper aiming angle;

then tighten the knob.

Please note this Helmet Mount will only work with vented

helmets.

TILT

KNOB

LOCKING

WHEEL

STRAP

1/4-20

SCREW

MOUNT

Mounting Adaptor

(Shield)

1. The camera clips into the

Mounting Adaptor.

2. The Mounting Adapter

allows you to aach

mounting accessories that

have a 1/4-20 screw.

TECHNICAL SPECIFICATIONS

Image Seings Centre Metering, Auto ISO

Lens F/3.1, f = 9.3 mm, View Angle 120°

Video Resolution 1280 x 720 (720p @30fps), 640 x 480 (480p

@60fps)

Picture Resolution 5.1MP (2592 x 1944), 3.0MP (2048 x 1536),

1.3MP (1280 x 1024)

Storage Media (not included) microSD/microSDHC (up to 32GB)

File Format JPEG / AVI

Interface USB 2.0 / Mini USB

Power Source Built in rechargeable Lithium-ion baery

Built-in Wi-Fi 802.11 b/g/n

Dimensions 67 x 44 x 28 mm

Weight 47g

For more information visit

www.3sixtgear.com

or visit www.3sixtgear.com/support

DV123SANC-3S

3SIXT DV123SANC-3S User manual

Brand: 3SIXT

Model: DV123SANC-3S

Type: User manual

Download PDF

report

3SIXT DV123SANC-3S User manual

3SIXT DV123SANC-3S User manual

Other documents