SUBLIMATION Vacuum Heat Press Machine User manual

Brand
SUBLIMATION
Model
Vacuum Heat Press Machine
Type
User manual
THE PHOTO GIFTS ITENS ARE NOT INCLUED.
+
A new generation of sublimation printing technology.
These machines are multi-functional. They can print
mugs, plates, ceramic tiles, crystals, glasses, cell
phone cases, ipad cases etc.
VACUUM HEAT PRESS MACHINE
3D SUBLIMATION
Colours
Available in
Various
SKU: 3DSUB-black
SKU: 3DSUB-red
SKU: 3DSUB-green
SKU: 3DSUB-blue
SKU: 3DSUB-silver
Find out more information on our website
THE PHOTO GIFTS ITENS ARE NOT INCLUED.
+
A new generation of sublimation printing technology.
These machines are multi-functional. They can print
mugs, plates, ceramic tiles, crystals, glasses, cell
phone cases, ipad cases etc.
VACUUM HEAT PRESS MACHINE
3D SUBLIMATION
Colours
Available in
Various
SKU: 3DSUB-black
SKU: 3DSUB-red
SKU: 3DSUB-green
SKU: 3DSUB-blue
SKU: 3DSUB-silver
Find out more information on our website
THE PHOTO GIFTS ITENS ARE NOT INCLUED.
+
A new generation of sublimation printing technology.
These machines are multi-functional. They can print
mugs, plates, ceramic tiles, crystals, glasses, cell
phone cases, ipad cases etc.
VACUUM HEAT PRESS MACHINE
3D SUBLIMATION
Colours
Available in
Various
SKU: 3DSUB-black
SKU: 3DSUB-red
SKU: 3DSUB-green
SKU: 3DSUB-blue
SKU: 3DSUB-silver
Find out more information on our website
INSTRUCTION MANUAL
Contents
P2. Safety Instructions
P3. Contents
P4. Features
P5. Compatible Products
P6. TechnicalSpecications
P7. Inside the Box
P8. Operation Instructions
P10. The Vacuum Tray
P11. Replacing Parts & Draining Filter
P12. Producing Mugs
P13. Producing Plates
P14. Producing Phones (Metallic Sheet Method)
P15. Producing Phones / Tablets (Plastic Full Cover)
P16. Producing Acrylic Frame
P17. Producing Ceramic Tile
P18. Troubleshooting
Important Safety Instructions
When using your 3D Sublimation machine, basic precautions should
always be used including the following points:
1. Read all instructions
2. Use 3D Heat Press only for its intended purpose
3. To reduce the risk of electric shock do not expose the 3D Sublimation
Vacuum Heat Press to water or other liquids.
4.Whennishedwithmachine,turnunitoffbeforedisconnecting
the plug from the socket. Never pull the cord to disconnect from
power outlet. Instead grasp plug and pull to disconnect.
5. Do not allow power cord to touch hot surfaces. Please ensure the
3D Heat Press has cooled completely before putting away.
6. Do not operate appliance with a damaged power cord, or if the
appliance has been dropped or damaged.
7. To reduce the risk of electric shock, do not disassemble or attempt
to repair the 3D Heat Press. Please contact your reseller for
examination and repair (based on the terms of your warranty).
Incorrectreassemblyorrepaircouldcauseariskofre,electric
shock, or injury to persons when the appliance is used.
Any attempt to repair or tamper with the unit will void warranty.
8. Children are not allowed to operate this appliance, please do not
leave the appliance unattended while connected.
9. Severe burns could occur from touching hot metal parts.
10. To reduce the likelihood of circuit overload, do not operate
another high voltage appliance on the same circuit
11. If an extension cord is absolutely necessary, a 20 amp rated cord
should be used. Power cords rated for less amperage may overheat,
care should be taken to arrange the cord so that the power cord
cannot be pulled or tripped over.
Features:
Safety
Software and hardware dual temperature control design, when one
thermostat failure, the other thermostat automatically work, 15 minutes
no operation, automatic shutdown, more secure and reliable.
ThemachinehasappliedforCE\ULsafetycertication
Efcient
The 300X420X110mm capacity reactor core design capacity,
can put 12 mugs at one time, greatly improve work performance.
Delicate
Bump dots surface design, greatly improve the heat area, die-cast
aluminum alloy heating far infrared radiation coating, so that each
point of the temperature of the furnace are uniform to ensure that
the image transfer more delicate and clear.
Simple
The machine adopts special high impedance contingent, insulation
materials, lightweight and safe, streamlined resistance heat strips,
compact and practical internal structure, simple and stylish appearance.
Sharp
108Degreeclamshelldesign,easyoperation,signicantspacesaving.
Highly Intelligent
Work without any key operation, just gently close the cover,
the machine will automatically aspirate, countdown and heat up.
Whentheworkiscompleted,automaticallydeated,
All you need is a simple process to place and remove products
User-Friendly
Forrsttimeuse,thetemperatureandtimeset-upprocessisveryeasy
to understand and easy to learn.
Environmental Protection
Efcientactivatedcarbonairlterisinstalledinthemachine,effectively
to worry too much toxic and harmful gases generated in the transfer
process, transported to the outdoors through the long catheter to
ensure the health and safety of the operating personnel.
Multifunctional
The machine covers all the functions of the heat transfer machine,
which can transfer mug, glass, crystal, acrylic, plastic, wood, metal,
stone,clothandsoon.withvarioustypesofxture,candosublimation
transfer on different size and shape of mugs. Transfer large format,
delicate, clear, high color reproduction, far more than the traditional
heat transfer machine.
THERE ARE LOTS OF THINGS
THAT YOU CAN CREATE
USING 3D SUBLIMATION
THESE ARE JUST A FEW OF THE
EXAMPLES OF PRODUCTS
THAT YOU CAN MAKE
PLEASE CHECK OUR WEBSITE
FOR OUR LATEST RANGE
www.photomart.co.uk
TEDDY BEARS
PHONE COVERS
METAL SHEETS
SHOT GLASSES
PLASTIC FLASKS
ACRYLIC
LAPTOP CASES METAL BOTTLES
PHOTO CLOCKS CERAMIC PLATES
PATCH MUGS
CERAMIC MUGS
MOUSE PADS
JIGSAW PUZZLES
PHOTO ROCKS
CERAMIC TILES
TechnicalSpecications
Measurement 685 x 545 x 400mm
CBM 0.15 CBM
GW 20kg (44lb)
NW 16kg (35lb)
Power 2600W
Voltage 220 V
Working Area 300 x 420 x 110mm
(11.8 x 16.5 x 4.3inch)
Up Heating 1200W
Down Heating 1200W
Vacuum Pump 150W
Max Vacuum -640mmHg
Vacuum Flow 33L/min
SILICONE
SHEET
POWER
CABLE
METAL
GRILL
INSTRUCTION
MANUAL
EXHAUST
PIPE
SAFETY
GLOVES
3 x MUG WRAPS
(VARIOUS STYLES)
ADDITIONAL ACCESSORIES
INSIDE THE BOX
Operating Instructions
For best results, the 3D Sublimation Machine should be placed on
alevel,clean,stable,well-ventilatedworkareafreeofammable
materials. It is recommended that the unit be plugged directly
into an AC power outlet.
When operating the machine, heat protection gloves should be
worn at all times to prevent serious burns or other injuries.
Please keep the machine dry and away from water.
Removal from Box
1. Remove the 3D Sublimation Machine Carefully from the Box
2. Inspect all cabling, wiring and machine body to ensure the unit
has not been damaged in transit.
3. Set unit on a clear table that is strong enough to support your
working environment and the weight of the machine.
Cabling
1. The 3D Sublimation Machine comes with the vacuum unit installed
inside the main unit. All cables are connected inside before shipment.
2. The Power Cable and Vacuum Exit Hose need to be attached.
3. Plug in power cable to an AC outlet.
Operating the Touch Screen Panel
For best results, the 3D Sublimation Machine should be placed on
Buttons
Indicators
Heating Switch
Temperature Settings
Time Settings
Power Switch
Vacuum Switch
Timer Start Switch
Top Heat Tray
Bottom Heat Tray
Vacuum Pump
Timer Indicator
The the rst push will turn on the top heater.
The second push will turn on the bottom heater.
The third push will turn on both heaters.
Hold for 3 Seconds to set Temperature Compensation
Turn Switch on First
Press Button to activate and deactivate
the Standby Mode
Power is 10w when left on Standby
Push once to activate Temperature Settings
Use + or - Keys to Set Temperature
Push Button again to Conrm Temperature.
Push the Button to activate the Vacuum Pump.
Push again to Manually disable the Vacuum Pump
If turned on with the timer, the pump will switch
itself off automatically.
Push once to activate Time Settings
Use + or - Keys to Set Timer
Push Button again to Conrm Time Setting
When the time has been set, push once to activate.
The time is measured in seconds
When the countdown nished, the heater and vacuum
will turn off automatically and will beep 3 times.
Removing the Vaccum Press Tray
1. Ensure the Machine has cooled down to normal temperature
2. Lock the 3D Press Tray using the Handle
3. Open the Lid Fully
4. Lift up the 3D Press Tray Vertically
5. Unscrew the Pipe from the bottom of 3D Press Tray and Remove
6. Remove Metal Grill
7. Unscrew the other end of Pipe from the bottom of Machine
8. Place Metal Grill Back in Place
9. Machine is Ready to be used in Oven Mode.
Replacing the Vaccum Press Tray
1. Ensure Machine has cooled down to normal temperature
2. Lift the Lid Fully
3. Remove the Grill
4. Screw one end of the pipe back into the bottom of machine
5. Replace Metal Grill ensuring pipe goes through it
6. Screw other end of pipe into bottom of vacuum tray
7. Place Vacuum Tray back into the machine
8.Machine is now Ready for Vacuum Mode
Replacing the Air Filter
1. Ensure the Machine is switched off and cool down
2. Use a magnetic screwdriver to remove the screws from back panel
3. Remove the Back Panel
4. Remove Air Filter from it’s holder (note: do not remove pipes)
5. By Hand, Carefully Unscrew the Glass Cover
6. Empty out the Glass Cover and clean, ensuring it is dry.
7.Unscrewthescrewholdingwhitelterinplace.
8.Removewhitelterfromholderanddispose
9. Clean the holder with a small smooth cloth.
10.Replacewithanewwhitelter.
11. Replace Screw holding it into place
12. By Hand replace the Glass Cover
13. Place Filter Back into Position
14. Replace Back Cover
15. Using Magnetic screwdriver screw cover back into place
16. Machine is Ready for use.
Mugs:
Instructions
1. Prepare your design to the size of your mug
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. When dry, cut the Paper, allowing 0.5cm Blank Edge on each side.
5. Use suitable tape to stick the paper to the mug from the sides
6. PlaceRubberGriparoundtheMugensuringitlocksrmlyintoplace.
7. Ensure the Tray Section is Removed (refer to section: Vacuum Tray)
8. Turn Vacuum Press Machine on, and set to Temperature
190 degrees, then press the Heating Button twice
(2 red lights will light up)
9. When temperature has been reached, place your mug/s
(up to 12) upside down onto the grill and close the lid.
10. Set time to the following from 6 Minutes (1 Mug) to 8 Minutes (12 Mugs)
11. Press the Vacuum Button, and the Timing Button and leave the machine.
12. As soon as the time has been reached, the Vacuum will switch
itself off automatically and machine will beep
13. Remove mugs, and leave to cool down before removing the paper
Plates:
Instructions
1. Prepare your design to the size of your plate
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. When dry, cut the Paper, and stick it tightly around the edge
of the print to plate using appropriate tape
5. Place plate onto the Vacuum Tray of the Machine
6. Cut a Small Strip of Paper, and place it over the edge of one
side of the plate (so that part of it is covering plate and part
of it is hanging over)
7. Turn Vacuum Press Machine on, and set to Temp 190 degrees,
then press the Heating Button twice (2 red lights will light up)
8. When temperature has been reached, place your plates
(up to 2) face up onto vacuum tray abd close the lid
9. Set time to the following from 5 Minutes(1 Plate) to 6 Minutes (2 Plates)
10. Press the Vacuum Button, and the Timing Button to start the process.
11. Check that the Rubber Cover Pressed “Into” the plate rather than over it
12. Close the lid of the Vacuum Press and leave the machine.
13. As soon as the time has been reached, the Vacuum will switch
itself off automatically and the machine will beep
14. Remove plate, and leave to cool down before removing the paper
Phone Cover:
(Metallic Sheet Method)
Instructions
1. Prepare your design to the size of your sheet (2mm Bleed)
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. Remove the protective sheet from the phone cover and place
metal sheet coated down onto the transfer paper. Cut
around the paper until you have enough to fold around the
metal sheet and stick it using appropriate adhesive tape.
5. Turn Vacuum Press Machine on, and set to Temp 190 degrees,
then press the Heating Button twice (2 red lights will light up)
6. When temperature has been reached, place your plates
(up to 4) face up onto vacuum tray abd close the lid
7. Set time to the 3 Minutes:
(Important Note: Any additional time will bend the metal.)
8. Press the Vacuum Button, and the Timing Button to start the process.
9. Check that the Rubber Cover Clings Tightly Around the Sheet
10. Close the lid of the Vacuum Press and leave the machine.
11. As soon as the time has been reached, the Vacuum will
switch itself off automatically and machine will beep
12. Remove plate, and leave to cool down before removing the paper
13. Peel off adhesive cover from the top of the Plastic Phone Cover
14. Stick the Metallic Sheet inplace on the Plastic Phone Cover.
Phone/Tablet Cover:
(Full Plastic Cover Method)
Instructions
1. Prepare your design to the size of your Cover
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. When dry, cut the Paper, and stick it tightly around the edge
of the print to cover using appropriate tape
5. Place the Cover around the compatible Jig/Mould
6. Turn Vacuum Press Machine on, and set to Temp 190 degrees,
then press the Heating Button twice (2 red lights will light up)
7. When temperature has been reached, place your covers (up to 4)
cover side up onto vacuum tray and close the lid
8. Set time to the following from 3 Minutes(1 Cover) to 4 Minutes (4 Covers)
9. Press the Vacuum Button, and the Timing Button to start the process.
10. Check that the Rubber Cover goes tightly around the cover.
11. Close the lid of the Vacuum Press and leave the machine.
12. As soon as the time has been reached, the Vacuum will
switch itself off automatically and machine will beep
13. Remove cover/s, and leave to cool down before removing the paper
Acrylic Frame:
Instructions
1. Prepare your design to the size of your Acrylic(2mm Bleed)
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. Remove the protective sheet from the back of the acrylic
sheet, place acrylic adhesive side down onto your print, and
stick around sides using suitable tape
5. Turn Vacuum Press Machine on, and set to Temp.190 degrees,
then press the Heating Button twice (2 red lights will light up)
6. When temperature has been reached, place your
acrylics onto vacuum tray and close the lid
7. Set time to the 3 Minutes:
(Important Note: Any additional time will melt the acrylic.)
8. Press the Vacuum Button, and the Timing Button to start the process.
9. Check that the Rubber Cover Clings Tightly Around the
Acrylic and Paper
10. Close the lid of the Vacuum Press and leave the machine.
11. As soon as the time has been reached, the Vacuum will
switch itself off and machine will beep
12. Remove Acrylic, and leave to cool down before removing the paper
Ceramic Tiles:
Instructions
1. Prepare your design to the size of your Tile
2. Using a Sublimation Printer, Print the design in reverse onto Paper
3. Allow the paper a few minutes to dry
4. When dry, cut the Paper, and stick it tightly around the edge
of the tile using appropriate tape
5. Cut a Small Strip of Paper, and place it over the edge of one
side of the plate (so that part of it is covering plate and part
of it is hanging over)
6. Turn Vacuum Press Machine on, and set to Temp 190 degrees,
then press the Heating Button twice (2 red lights will light up)
7. When temperature has been reached, place your Tile
(up to 4) face up onto vacuum tray and close the lid
8. Set time to the following from 5 Minutes(1 Tile) to 6 Minutes (4 Tiles)
9. Press the Vacuum Button, and the Timing Button to start the process.
10. Close the lid of the Vacuum Press and leave the machine.
11. As soon as the time has been reached, the Vacuum will
switch itself off and machine will beep
12. Remove plate, and leave to cool down before removing the paper
13. Remove Adhesive Back from Tile Frame, and Stick Tile in Place
Troubleshooting:
Q. Transfer Paper appears yellow after process?
A. Lower Temperature and/or Reduce Heating Time
Q: The text appears very faint?
A: Lower Temperature and/or Reduce Heating Time
Q. Paper still stays same after process?
A. Use Higher Temperature and/or Increase Heating Time
Q: Colours do not appear good on Product?
A: Use Higher Temperature and/or Increase Heating Time
Q: Sometimes Get White Stains?
A: Use Higher Temperature and/or Increase Heating Time
Q. The Effect does not look good on certain textures?
A. Temperature and Time have to be changed accordingly
This will be vary based on a number of factors including:
- Paper Quality
- Printing Machine
- Product Texture
- Temperature Conditions
Q: Keep getting excess powder around your image?
A:Pleaseensureyouhaveallowedsufcienttimeforyoursunlimation
print to dry before putting it onto your material
Q: Machine switches off if I leave it alone for a long time?
A: This is intentional by design, the machine is set to switch off
automatically after 15 minutes making it safe and reliable
Q: The printing appears to be unclear?
A: 1) Check the Vacuum guage to see if the vacuum pressure
reaches 0.64mmhg. If the pressure fails to reach he value,
leakage can be assured. Check the vacuum extracting strip
to see if it’s well sealed.
2) Check connections of pipe for looseness or leakage
Troubleshooting (Continued):
Q. What if automatic operation failed, including air extraction,
suction and countdown?
A. Adjust the distance between the vacuum extracting plate and
the switch. Normally, the distance shall be at 3mm, magnet
strength will be weak if the distance is too far.
Q. What if abnormal sound occurs and the machine fails to run normally?
A. 1) Open the cover of the rear power box and check if any
wind-up on the vacuum fan. If there is, unwire it.
2) Checkifthereisanywaterintheairlter.Waterneedstobe
emptiedandtheltercorewillneedtobereplacedperiodically.
Q. The Machine fails to heat and temperature does not rise?
A. Check if the heating switch has been turned on and the indicators
on the display are glistening. If not, turn on the switch.
Q. There is a big gap found between the set and real temperature.
A: 1) Overheating within 30 Degrees C is acceptable when the
metal heating pipes are working properly
2) Check if the cooling fan beneath the circuit board works normally.
If there is any damage, the fan needs to be replaced.
3) The machine is designed with double circuit for temperature control,
keeping the inner oven temperature below 210 Degrees C,
otherwise the machine will cease heating.
for more information write us :
[email protected]
Reach us on
011-65453987
Mobilesstop.Com
www.99sublimation.com
B282, Sector 7 , Dwarka,
New Delhi 110075
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

SUBLIMATION Vacuum Heat Press Machine User manual

Brand
SUBLIMATION
Model
Vacuum Heat Press Machine
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents