Rodgers Infinity organ Owner's manual

Brand: Rodgers

Model: Infinity organ

Category: Supplementary music equipment

Type: Owner's manual

Innity Organ

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING - When using electric products, basic precautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

WARNING:

IMPORTANT:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

THIS APPARATUS MUST BE EARTHED

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE

For the U.K.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified

by the manufacturer.

12. Unplug this apparatus during lightning storms or when

unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY”

(p. 3), and “IMPORTANT NOTES” (p. 5). These sections provide important information concerning the proper operation of the unit.

Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s Manual

should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

USING THE UNIT SAFELY

WARNING

Make sure that the power cord is grounded

Connect mains plug of this model to a

mains socket outlet with a protective

earthing connection.

Do not disassemble or modify by yourself

Do not open or perform any internal

modications on the unit.

Do not repair or replace parts by yourself

Do not attempt to repair the unit, or

replace parts within it (except when this

manual provides specic instructions

directing you to do so). Refer all servicing

to your retailer, or Rodgers Instruments

Corporation, as listed on the “Notice to

Users” (p. 6).

Do not use or store in the following types of

locations

• Subject to temperature extremes

(e.g., direct sunlight in an enclosed

vehicle, near a heating duct, on top of

heat-generating equipment); or are

• Damp (e.g., baths, washrooms, on wet

oors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Humid; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and

shakiness.

Connect the power cord to an outlet of the correct

voltage

The unit should be connected to a power

supply only of the type described as

marked under the keyboard deck of unit.

WARNING

Do not bend the power cord or place heavy objects

on it

Do not excessively twist or bend the

power cord, nor place heavy objects

on it. Doing so can damage the cord,

producing severed elements and short

circuits. Damaged cords are re and

shock hazards!

Avoid extended use at high volume

This unit, either alone or in combination

with an amplier and headphones or

speakers, may be capable of producing

sound levels that could cause permanent

hearing loss. Do not operate for a long

period of time at a high volume level, or

at a level that is uncomfortable. If you

experience any hearing loss or ringing

in the ears, you should immediately

stop using the unit, and consult an

audiologist.

Don’t allow foreign objects or liquids to enter unit;

never place containers with liquid on unit

Do not place containers containing liquid

(ower vases) on this product. Never

allow foreign objects (e.g., ammable

objects, coins, wires) or liquids (e.g.,

water or juice) to enter this product.

Doing so may cause short circuits, faulty

operation, or other malfunctions.

Adults must provide supervision in places where

children are present

When using the unit in locations where

children are present, be careful so no

mishandling of the unit can take place.

An adult should always be on hand to

provide supervision and guidance.

WARNING

Turn o the unit if an abnormality or malfunction

occurs

Immediately turn the unit o, remove the

power cord from the outlet, and request

servicing by your retailer, or Rodgers

Instruments Corporation, as listed on the

“Notice to Users” (p. 6) page when:

• The power-supply cord or the plug has

been damaged; or

• If smoke or unusual odor occurs; or

• Objects have fallen into, or liquid has

been spilled onto the unit; or

• The unit has been exposed to rain (or

otherwise has become wet); or

• The unit does not appear to operate

normally or exhibits a marked change

in performance.

Do not drop or subject to strong impact

Protect the unit from strong impact.

(Do not drop it!)

Do not share an outlet with an unreasonable

number of other devices

Do not force the unit’s power-supply cord

to share an outlet with an unreasonable

number of other devices. Be especially

careful when using extension cords—the

total power used by all devices you have

connected to the extension cord’s outlet

must never exceed the power rating

(watts/amperes) for the extension cord.

Excessive loads can cause the insulation

on the cord to heat up and eventually

melt through.

Do not use overseas

Before using the unit in a foreign country,

consult with your retailer, or Rodgers

Instruments Corporation, as listed on the

“Notice to Users” (p. 6).

Used for instructions intended to alert the

user to the risk of injury or material

damage should the unit be used

improperly.

* Material damage refers to damage or

other adverse effects caused with

respect to the home and all its

furnishings, as well to domestic animals

or pets.

Used for instructions intended to alert the

user to the risk of death or severe injury

should the unit be used improperly.

The symbol alerts the user to things that must be

carried out. The specific thing that must be done is

indicated by the design contained within the circle. In the

case of the symbol at left, it means that the power-cord

plug must be unplugged from the outlet.

The symbol alerts the user to important instructions or

warnings.The specific meaning of the symbol is

determined by the design contained within the triangle. In

the case of the symbol at left, it is used for general

cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be

carried out (are forbidden). The specific thing that must

not be done is indicated by the design contained within

the circle. In the case of the symbol at left, it means that

the unit must never be disassembled.

About WARNING and CAUTION Notices

About the Symbols

ALWAYS OBSERVE THE FOLLOWING

USING THE UNIT SAFELY

CAUTION

Place in a well ventilated location

The unit should be located so that its

location or position does not interfere

with its proper ventilation.

Grasp the plug when connecting or disconnecting

the power cord

Always grasp only the plug on the

power-supply cord when plugging into,

or unplugging from, an outlet.

Periodically clean the power cord’s plug

At regular intervals, you should unplug

the power plug and clean it by using

a dry cloth to wipe all dust and other

accumulations away from its prongs.

Also, disconnect the power plug from

the power outlet whenever the unit is to

remain unused for an extended period of

time. Any accumulation of dust between

the power plug and the power outlet can

result in poor insulation and lead to re.

Manage cables for safety

Try to prevent cords and cables from

becoming entangled. Also, all cords and

cables should be placed so they are out

of the reach of children.

Avoid climbing on top of the unit, or placing heavy

objects on it

Never climb on top of, nor place heavy

objects on the unit.

Do not connect or disconnect the power cord with

wet hands

Never handle the power cord or its

plugs with wet hands when plugging

into, or unplugging from, an outlet.

Cautions when moving this unit

Since this product is very heavy, you

must make sure that a sucient number

of people are on hand to help, so you can

lift and move it safely, without causing

strain. Make sure to have a rm grip,

to protect yourself from injury and the

instrument from damage.

If you need to move the instrument,

consult with your retailer, or Rodgers

Instruments Corporation, as listed on the

“Notice to Users” (p. 6).

Unplug the power cord from the outlet before

cleaning

Before cleaning the unit, turn it o and

unplug the power cord from the outlet.

If there is a possibility of lightning strike, disconnect

the power cord from the outlet

Whenever you suspect the possibility of

lightning in your area, pull the plug on

the power cord out of the outlet.

CAUTION

Take care not to get ngers pinched by lid

Be careful so you don’t get your ngers

pinched when you handle any moving

parts such as the following. Adult

supervision is recommended whenever

small children use the unit.

• Lid

Precautions concerning use of bench

When using the bench, please observe

the following points:

• Do not allow two or more persons to sit

on the bench.

• Do not adjust the height while sitting

on the bench.

Do not remove the speaker grille and speaker

Do not remove the speaker grille and

speaker by any means. Speaker not user

replaceable. Shock hazardous voltages

and currents are present inside the

enclosure.

Power Supply

• Do not connect this unit to same electrical outlet

that is being used by an electrical appliance that

is controlled by an inverter or a motor (such as a

refrigerator, washing machine, microwave oven, or

air conditioner). Depending on the way in which

the electrical appliance is used, power supply noise

may cause this unit to malfunction or may produce

audible noise. If it is not practical to use a separate

electrical outlet, connect a power supply noise lter

between this unit and the electrical outlet.

• To prevent malfunction and equipment failure,

always make sure to turn o the power on all your

equipment before you make any connections.

• Although the LCD and LEDs are switched o when

the unit is turned o, this does not mean that the

unit has been completely disconnected from the

source of power. If you need to turn o the power

completely, rst turn o the unit’s switch, then

unplug the power cord from the power outlet. For

this reason, the outlet into which you choose to

connect the power cord’s plug should be one that

is within easy reach and readily accessible.

• With the factory settings, the power will

automatically be switched o 240 minutes after

you stop playing or operating the unit. If you don’t

want the unit to turn o automatically, change the

“Auto O” (p. 19) setting to “OFF” as described on

“Making Settings in the Menus” (p. 15).

NOTE

The settings you were editing will be lost when the

unit is turned o. If you want to keep your settings,

you must save your settings before turning the

unit o.

Placement

• Using the unit near power ampliers (or other

equipment containing large power transformers)

may induce hum. To alleviate the problem, change

the orientation of this unit; or move it farther away

from the source of interference.

• This device may interfere with radio and television

reception. Do not use this device in the vicinity of

such receivers.

• Noise may be produced if wireless communications

devices, such as cell phones, are operated in the

vicinity of this unit. Such noise could occur when

receiving or initiating a call, or while conversing.

Should you experience such problems, you should

relocate such wireless devices so they are at a

greater distance from this unit, or switch them o.

• Do not expose the unit to direct sunlight, place it

near devices that radiate heat, or otherwise subject

it to temperature extremes. Also, do not allow

lighting devices that normally are used while their

light source is very close to the unit (such as a piano

light), or powerful spotlights to shine upon the

same area of the unit for extended periods of time.

Excessive heat can deform or discolor the unit.

• Do not allow rubber, vinyl, or similar materials to

remain on this unit for long periods of time. Such

objects can discolor or otherwise harmfully aect

the nish.

• Do not allow objects to remain on top of the

keyboard or pedal board. This can be the cause

of malfunction, such as keys ceasing to produce

sound.

• Do not paste stickers, decals, or the like to this

instrument. Peeling such matter o the instrument

may damage the exterior nish.

• Do not put anything that contains water on this

unit. Also, avoid the use of insecticides, perfumes,

alcohol, nail polish, spray cans, etc., near the unit.

Swiftly wipe away any liquid that spills on the unit

using a dry, soft cloth.

Maintenance

• To clean the unit, use a dry, soft cloth; or one that

is slightly dampened. Try to wipe the entire surface

using an equal amount of strength, moving the

cloth along with the grain of the wood. Rubbing

too hard in the same area can damage the nish.

• Never use benzine, thinners, alcohol or solvents of

any kind, to avoid the possibility of discoloration

and/or deformation.

Repairs and Data

• Please be aware that all data contained in the

unit’s memory may be lost when the unit is sent for

repairs. Important data should always be backed

up the USB ash drive, or written down on paper

(when possible). During repairs, due care is taken

to avoid the loss of data. However, in certain cases

(such as when circuitry related to memory itself is

out of order), we regret that it may not be possible

to restore the data, and Rodgers assumes no

liability concerning such loss of data.

Additional Precautions

• Please be aware that the contents of memory can

be irretrievably lost as a result of a malfunction,

or the improper operation of the unit. To protect

yourself against the risk of loosing important data,

we recommend that you periodically save a backup

copy of important data you have stored in the USB

ash drive.

• Unfortunately, it may be impossible to restore

the contents of data that was stored in the unit’s

memory or USB ash drive once it has been

lost. Rodgers Corporation assumes no liability

concerning such loss of data.

• Use a reasonable amount of care when using the

unit’s buttons, sliders, or other controls; and when

using its jacks and connectors. Rough handling can

lead to malfunctions.

• Never strike or apply strong pressure to the display.

• When disconnecting all cables, grasp the connector

itself—never pull on the cable. This way you will

avoid causing shorts, or damage to the cable’s

internal elements.

• A small amount of heat will radiate from the unit

during normal operation.

• To avoid disturbing others nearby, try to keep the

unit’s volume at reasonable levels. You may prefer

to use headphones, so you do not need to be

concerned about those around you.

• When you need to transport the unit, pack it in

shock-absorbent material. Transporting the unit

without doing so can cause it to become scratched

or damaged, and could lead to malfunction.

• Do not apply undue force to the music stand while

it is in use.

• Some connection cables contain resistors. Do not

use cables that incorporate resistors for connecting

to this unit. The use of such cables can cause the

sound level to be extremely low, or impossible

to hear. For information on cable specications,

contact the manufacturer of the cable.

• Due to the structural design of this instrument,

small pets or other animals could end up getting

trapped inside it. If such a situation is encountered,

you must immediately turn o the unit and

disconnect the power cord from the outlet. You

should then consult with the retailer from whom

the instrument was purchased, or contact Rodgers

Instruments Corporation, as listed on the “Notice to

Users” (p. 6).

• When opening or closing the lid, please be careful

not to get your ngers pinched between the

movable part and the panel.

• The explanations in this manual include

illustrations that depict what should typically be

shown by the display.

Note, however, that your unit may incorporate

a newer, enhanced version of the system (e.g.,

includes newer sounds), so what you actually see

in the display may not always match what appears

in the manual.

Before Using External Memories

Using External Memories

• Carefully insert the USB ash drive all the way

in—until it is rmly in place.

• Never touch the terminals of the USB ash drive.

Also, avoid getting the terminals dirty.

• USB ash drive is constructed using precision

components; handle the cards carefully, paying

particular note to the following.

• To prevent damage to the cards from static

electricity, be sure to discharge any static

electricity from your own body before handling

the cards.

• Do not touch or allow metal to come into contact

with the contact portion of the cards.

• Do not bend, drop, or subject cards to strong

shock or vibration.

• Do not keep cards in direct sunlight, in closed

vehicles, or other such locations.

• Do not allow cards to become wet.

• Do not disassemble or modify the cards.

IMPORTANT NOTES

Contents

USING THE UNIT SAFELY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ABOUT THE PERFORMANCE TOUCH KEYBOARDS . . . . . . . . . . . 7

Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Contents of the Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

About Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

About Toe Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

About Tablets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display and Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

External Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

About the Music Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

About the Pedalboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Making Settings in the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Menu List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Hymn Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Song Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Pitch/Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Room Modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

MIDI Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Tremulant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Exp. Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Crescendo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Save/Load (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Storing Your Settings (Customize) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Selecting Stops (Sounds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Selecting a Sound Variation (Voice Palette) . . . . . . . . . . . . . . . . . . . . . . .25

Selecting a Sound Variation (Stop Library) . . . . . . . . . . . . . . . . . . . . . . . .25

Storing a Combination of Stops . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Storing or Recalling a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Storing a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Recalling a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Resetting the Sound Settings (General Cancel) . . . . . . . . . . . . . . . . . . .26

Using Memory Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Storing the Combination of Memory Pistons as a Memory

Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Recalling a Registration from a Dierent Memory Bank . . . . .27

Recalling Registrations Successively. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Using Memory Banks with USB Memory . . . . . . . . . . . . . . . . . . . . . . . . .28

Preparing USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Selecting USB Memory Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Storing the Combination of Memory Pistons as a Memory

Bank to USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Recalling a Registration from a Dierent Memory Bank from

USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Changing the Settings for TUTTI . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setting the Sounds to be Played When the [TUTTI] Piston is

Pressed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setting Whether Stop Illumination is On/O When the

[TUTTI] Piston is Pressed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Changing the Settings for Crescendo . . . . . . . . . . . . . . . . . . . . . 29

Changing ORGAN TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Practicing Along with a Preset Song or Performance Data . 30

Selecting and Playing Back a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Muting a Specic Division During Playback . . . . . . . . . . . . . . . . .31

Playing Back a Specic Division as a Guide Tone . . . . . . . . . . . .31

Recording Your Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Recording a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Play Back the Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Saving a Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Deleting a Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Copying a Saved Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Hymn Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Selecting Hymn or Prelude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Selecting Hymn number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Playing a Hymn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Playing a Prelude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Changing Hymn book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Saving and Loading Settings on a USB Flash Drive . . . . . . . . . 36

Formatting a USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Deleting a Memory Bank from a USB Flash Drive . . . . . . . . . . . . . . . . . 36

Copying a Memory Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Saving and Loading a Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Saving to USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Loading a Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Deleting a Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Backing Up Data/Performing an Initialization . . . . . . . . . . . . . 38

Returning all Settings to the Factory-Set State (Factory Reset). . . . . 38

Backing Up/Loading Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Displaying the Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

List of Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Notice to Users

Information in this document is subject to change without notice. No part of this manual may be translated into any language, stored in a retrieval

system, reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose

without the express written permission of Rodgers Instruments Corporation.

RODGERS INSTRUMENTS CORPORATION

1300 N.E. 25

Avenue

Hillsboro, Oregon 97124

(503) 648-4181

http://www.rodgersinstruments.com/

RODGERS IN CANADA

5480 Parkwood Way

Richmond, B.C. V6V 2M4

Toll Free (877) 676-5263

Rodgers instruments are manufactured and protected under one or

more of the following U.S. patents: 4,622,878, 5,060,179, 5,087,798,

5,091,613, 5,225,619, 5,262,581, 5,508,472, 6,369,310, 6,399,868

QuickMenu™, Rodgers®, Rodgers Classic Organs®, Digital Dynamic Wind™,

Dimensional Sound Modeling®, Parallel Digital Imaging®, Voice Palette™,

DVM™, PDI™, TrueChimes™, and Trillium Masterpiece™ are trademarks or

registered trademarks of Rodgers Instruments Corporation , Hillsboro,

Oregon. RSS® is a registered trademark of the Roland Corporation.

For generations, organ key tops were made from the best materials – ivory (for white keys) and ebony (for black keys). The Performance Touch keyboards

use the latest technologies to reproduce the touch and feel of these materials.

• Surfaces incorporate stripes of moisture-absorbing material for improved touch and playability.

• Keys feature a subtle gloss and understated coloring, enhancing the look and elegance.

• White keys are nished with a slight yellowish tinge for the look of real ivory.

 Note: — To Ensure Usage in Optimal Conditions —

Handling…

• Do not write on the keyboard with any pen or other implement, and do not stamp or place any marking on the instrument. Ink will seep into the surface

lines and become unremovable.

• Do not ax stickers on the keyboard. You may be unable to remove stickers that use strong adhesives, and the adhesive may cause discoloration.

Care and Maintenance…

Please note the following points. Failure to do so may result in scratches on the surface nish, damaged gloss, or other discoloration or deformation.

• Gently wipe dirt and grime with soft cloth; do not rub the surfaces forcefully.

• To remove more serious grime, use a commercial keyboard cleaner not containing abrasives.

• Do not use benzene, paint thinner, or alcohol on the keys.

ABOUT THE PERFORMANCE TOUCH KEYBOARDS

2-manual model

Quick Tour

WARNING

 With the factory settings, the power will automatically be switched o 240 minutes after you stop playing or operating the unit.

If the unit’s power has been turned o automatically, you can use the Power switch to turn the unit back on again.

If you don’t want the unit to turn o automatically, change the “Auto O” (p. 19) setting to “OFF” as described on “Making Settings in the Menus” (p. 15)

 When turning the power on again, you must allow at least ve seconds after power-o before you once again turn the power on. If you fail to allow enough time, the Auto O

function might not be reset, preventing the power from turning on correctly.

USB Memory Connector

External Connectors

Pedalboard

Power Switch

Headphone Jack

Pistons

Keyboard Cover

Tablets

Music Rest

Stops

Expression Pedals

Quick Tour

About the Display

Contents of the Main Screen

USB Memory Connector

Power Switch

Headphone Jack

Keyboard Cover

Stops

External Connectors

Pedalboard

Pistons

Tablets

Music Rest

Expression Pedals

1. General memory bank number

2. General memory piston number

3. Keyboard transposition status

Range (semitones)

-6–+5

4. Reference pitch (master tuning)

Available Settings (Hz)

392: VERSAIL (VERSAILLES)

415: BAROQUE

440: MODERN (standard)

465: VENETIA (VENETIAN)

MEMO

You can also adjust this tuning within the range of the reference pitch.

5. Temperament

Available Settings

EQUAL, WERCK., KIRN.1, KIRN.3, VALLO., MEAN.D, MEAN.E, PYTHG., M.BACH

6. Displayed when the MIDI Visual Control function is on.

7. Crescendo pedal status

8. Volume of the SWELL and SOLO expression pedal

9. Volume of the GREAT, PEDAL, and CHOIR expression pedal

3-manual model

Quick Tour

Piston Explanation

1 [ORGAN TYPE] Piston This piston allows you to select Organ Type.

2 [SET] Piston

This stores a combination of sounds (registration)

to a general memory piston or a division memory

piston.

General Memory

Pistons

Each of these pistons can store a combination of

sounds (registration) for the entire organ.

Memory Bank Select

[M–] Piston/[M+] Piston

[M1] Piston

Use these pistons when you want to switch memory

banks. [M1] piston allows you to switch to memory

bank 1.

PEDAL Division

Coupler Piston

This piston causes the pedalboard to play the sound

of each division.

Division Memory

Pistons

Each of these pistons can store sounds (registration)

for each division.

7 Tremulant Pistons

The tremulant eect adds vibrato (cyclic

modulation) to the sounds. Refer to “Tremulant”

(p. 20).

[PREV] Piston/[NEXT]

Piston

These successively load the registration stored at

the previous or next general memory piston; e.g.,

2 1 ([PREV] piston) or 1 2 3 ([NEXT]

piston).

9 MIDI Coupler

These pistons allows you to play a MIDI coupler.

Refer to “MIDI Coupler” (p. 18).

Bass Coupler [BASS]

Piston

This causes the lowest note played on the 2nd

manual to play the PEDAL division sounds.

Melody Coupler Piston

This causes the highest note played on the 2nd

manual to play the SWELL, CHOIR, and SOLO

division sounds.

11 [HYMN PLAYER] Piston This piston allows you to play a Hymn.

Piston Explanation

[

] ([STOP]) Piston

This stops playback or recording of a song.

[

] ([PLAY/PAUSE])

Piston

This starts or pauses playback of a song.

[

] ([REC]) Piston

Use this when you want to record your performance.

General Cancel [0]

Piston

This cancels all stops, so that no sounds are selected.

It’s convenient to use this piston when you want to

specify a combination of sounds from scratch.

14 [TUTTI] Piston

The TUTTI control allows you to engage full organ

quickly without canceling the current registration.

SOLO Tremulant

Pistons

The tremulant eect adds vibrato (cyclic

modulation) to the sounds of the SOLO division.

Refer to “Tremulant” (p. 20).

16 Division Coupler Piston

This piston causes the 1st and 2nd manual to play

the sound of the SOLO division.

17 [ZIMBEL] Piston This piston allows you to play the Zimbelstern voice.

18 [DFLT STOPS] Piston

Press this piston; the settings will be reset to a state

in which no sound is selected and the variation

settings will also be reset for all stops, restoring the

basic variation VP0 (Default Voice Palette). Refer to

“Selecting a Sound Variation (Voice Palette)” (p. 25)

19 MIDI Coupler Pedal

This piston allows you to play a Pedal MIDI coupler.

Refer to “MIDI Coupler” (p. 18).

20 [GT/CH TARNS] Piston

This piston allows you to transfer the 1st manual

(CHOIR) and 2nd manual (GREAT).

[MAIN TREM ALT]

Piston

This Organ is equipped with two independent Main

Tremulant settings, a Standard Main Tremulant and

an Alternate Main Tremulant.

Pressing the [MAIN TEM ALT] reversible piston so

that its light engages the Alternate Main Tremulant.

Refer to “Tremulant” (p. 20).

About Pistons

2-manual model

ORGAN

TYPE

HYMN

PLAYER

TREM

MIDI

PED

MIDI

PED

MIDI

TREM

PED

TUTTI

MEL

ZIMBEL

CHIMES

1 3 7 92 12

4 5 6 8 10 13

141619

3-manual model

ZIMBEL

HYMN

PLAYER

ORGAN

TYPE

PED

MIDI

PED

MIDI

TREM

CHIMES

DFLT

STOPS

MEL

GT-PED

ENCL

MEL

TREM

MIDI

ALL

EXPR

MAIN

TREM

FLUTE

TREM

MIDI

EXPR

GT/CH

TRANS

ALT

CRESC

PED

TUTTI

17 18 23 24

1 3 7 92 12

4 5 6 819 13

1527 26

1420

Quick Tour

Piston Explanation

All Expression Shoe

SWELL Piston

Turn this piston on if you want to assign all divisions

to the SWELL expression shoe.

[FLUTE TREM ALT]

Piston

This tremulant is best used in gospel, theatre and

evangelical music; the Flute Vibrato aects Flute

voices.

This Organ is equipped with two independent Flute

Tremulant settings, a Standard Flute Tremulant and

an Alternate Flute Tremulant. Press the [FLT TEM

ALT] reversible piston so that its light engages the

Alternate Flute Tremulant. Refer to “Tremulant” (p. 20).

GREAT & PEDAL

Enclosed Piston

Turn this piston on if you want to use the expression

pedal to adjust the volume of the GREAT division

and PEDAL division.

25 [ALT CRESC] Piston

This Organ is equipped with two independent

Crescendo sequences, a Standard Crescendo and an

Alternate Crescendo.

Press the [ALT CRESC] reversible piston so that its

light engages the Alternate Crescendo sequence.

Refer to “Changing the Settings for Crescendo” (p. 29).

SOLO Division Memory

Pistons

Each of these pistons can store the sounds

(registration) for the SOLO division.

SOLO Expression Shoe

CHOIR Piston

Turn this piston on if you want to assign SOLO

divisions to the CHOIR expression shoe.

28 [GT CHIMES] Piston

This piston allows you to play the Chimes voice on

the 2nd manual (GREAT).

About Toe Pistons

1 2

Pedal/Piston Explanation

1 Expression Pedal

2-Manual Model

The volume of GREAT/PEDAL is adjusted with the

left pedal, and the center pedal is used to adjust the

volume of SWELL/SOLO.

3-Manual Model

The volume of CHOIR/GREAT/PEDAL is adjusted with

the left pedal, and the center pedal is used to adjust the

volume of SWELL/SOLO.

2 Crescendo Pedal

This shoe gradually adds a predetermined selection of

stops as it is pressed forward.

3 Toe Pistons

General Memory Piston

PEDAL Division Memory Piston

PEDAL Division Coupler Piston

[TUTTI] Piston

[NEXT], [PREV] Piston

PEDAL Stop Piston

Quick Tour

About Tablets

2-manual model

SWELL

GREAT

SWELL

UNISON

OFF

ALL

EXPR

SWELL

GREAT

SWELL

GREAT

SOLO

PEDAL

SWELL

PEDAL

GREAT

PEDAL

ANT

MAIN

OFF

1 32

3-manual model

SOLO

GREAT

CHOIR

GREAT

CHOIR

GREAT

CHOIR

GREAT

SWELL

GREAT

SOLO

SWELL

CHOIR

SWELL

SOLO

CHOIR

SWELL

CHOIR

SWELL

CHOIR

SWELL

CHOIR

SWELL

GREAT

ANC

PIPES

OFF

ANT

MAIN

OFF

SWELL

GREAT

SOLO

PEDAL

CHIOR

PEDAL

SWELL

PEDAL

SWELL

PEDAL

GREAT

PEDAL

SOLO

GREAT

CHOIR

GREAT

CHOIR

GREAT

CHOIR

GREAT

SWELL

GREAT

SOLO

SWELL

CHOIR

SWELL

SOLO

CHOIR

SWELL

CHOIR

SWELL

CHOIR

SWELL

CHOIR

SWELL

GREAT

ANC

PIPES

OFF

ANT

MAIN

OFF

SWELL

GREAT

SOLO

PEDAL

CHIOR

PEDAL

SWELL

PEDAL

SWELL

PEDAL

GREAT

PEDAL

1 2 9

7 8

Tablet Explanation

GREAT TO PEDAL 8

SWELL TO PEDAL 4

SWELL TO PEDAL 8

CHOIR TO PEDAL 8

SOLO TO PEDAL 8

This tablet causes the pedalboard to play the sounds of each division.

SWELL TO GREAT 4

SWELL TO GREAT 8

SWELL TO GREAT 16

CHOIR TO GREAT 4

CHOIR TO GREAT 8

CHOIR TO GREAT 16

SOLO TO GREAT 8

This tablet causes the 1st or 2nd manual (GREAT) to play the sounds of each division.

The 4-foot tablets play sounds an octave higher on each division.

The 16-foot tablets play sounds an octave lower on each division.

SWELL to SWELL 4

SWELL to SWELL 16

This tablet causes the 2nd manual (SWELL) to play sounds an octave higher or lower.

4 SWELL UNISON OFF This tablet causes the 2nd manual (SWELL) not to play sounds at the original octave.

MAIN OFF This piston silences the main organ system.

ANT ON

An antiphonal speaker system is so named because it is normally installed a substantial distance from the main organ.

This dierence in physical placement allows for a variety of eects.

6 ALL EXPR SWELL Turn this piston on if you want to assign all divisions to the SWELL expression shoe.

SWELL TO CHOIR 4

SWELL TO CHOIR 8

SWELL TO CHOIR 16

SOLO TO CHOIR 8

This tablet causes the 1st manual (CHOIR) to play the sounds of each division.

The 4-foot tablet play sounds an octave higher.

The 16-foot tablet play sounds an octave lower.

SOLO TO SWELL 8

CHOIR TO SWELL 8

CHOIR TO SWELL 4

This tablet causes the 3rd manual (SWELL) to play the sounds of each division.

The 4-foot tablet play sounds an octave higher.

PIPES OFF

When the [PIPES OFF] piston is engaged, the wind-blown pipe ranks are silenced.

 This is used when an optional pipe system has been connected.

ANC ON

When the [ANC ON] piston is engaged, digital voices play from the stops which normally control pipe voices. These digital voices

are often referred to as the “Ancillary.”

 This is used when an optional pipe system has been connected.

Quick Tour

Display and Panel

1. Display

Various information is shown here.

2. [Select/Menu] Knob

Turn: When you’re in a menu screen for making detailed settings, turn

this knob to select the item you want to operate.

Press: Takes you to a sub-menu, or selects a setting.

3. [Value/Exit Menu] Knob

Turn: Adjusts a setting.

Press: Returns you to the previous menu, or cancels an operation.

 To prevent malfunction and equipment failure, always turn down

the volume, and turn o all <remove> units before making any

connections.

 Carefully insert the USB ash drive all the way in until it is rmly in

place.

 This unit is equipped with a protection circuit. After turning on the

unit, a brief interval (a few seconds) is required before the unit will

operate normally.

 Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

 If you need to turn o the power completely, rst turn o the unit, then

unplug the power cord from the power outlet. Refer to “Power Supply”

(p. 5).

External Connectors

1 2 3

1. OUTPUT L/MONO, R (Output) Jacks

You can connect an external amplied speaker system here so that the

sound of the organ is played from the connected speakers.

2. INPUT L/MONO, R (Input) Jacks

You can connect an external sound module or similar device here so

that its sounds are heard from the organ’s speakers.

3. MIDI IN, OUT Connectors

You can connect external MIDI devices here to exchange performance

data with the organ.

Quick Tour

About the Music Rack

The music rack is movable up and down, back and forth. To tighten the locking screws, use the included Allen wrench.

About the Pedalboard

Connect the pedalboard and console with the provided cable.

Locking screws

Making Settings in the Menus

Heres how to make settings using the menus. Perform these steps from

the main screen. For a list of the menu items, refer to the next page.

1. Press the [Select/Menu] knob to access the menu.

2. Turn the [Select/Menu] knob to select the item.

3. Press the [Select/Menu] knob to enter the item.

4. Turn the [Value/Exit Menu] knob to change the item’s setting.

To cancel the setting / to return to the previous menu...

Press the [Value/Exit Menu] knob.

5. If a Yes/No conrmation screen appears, press the [SET]

piston to put the setting into eect.

Menu List

The settings shown below will revert to their default values when the organ’s power is turned o; however, with a number of the settings, you can have

their content saved in memory even after the power is turned o.

Setting items marked with [S] Can be stored in the SYSTEM group.

Refer to “Storing Your Settings (Customize)” (p. 24).

Setting items marked with [V] Can be stored in the VOICING group.

Setting items marked with [P] Settings can be stored on an individual piston basis. Refer to “Storing or Recalling a Registration” (p. 26).

Demo

Listen to demo songs

 No data for the music that is played will be output from the MIDI OUT connector.

Menu item Value Explanation

Group Demo song group

Song Demo song

Tempo Tempo of the demo song

Reverb Volume

[S]

SONG, 0–127

Adjusts the reverb volume of the demo songs.

If this is set to “SONG,” the reverb volume will automatically t with the demo song.

USB Memory

Selecting a USB Memory folder

Menu item Value Explanation

Folder A–Z Selecting a USB Memory folder

Making Settings in the Menus

Hymn Player

Play back Hymns and Preludes

Menu item Value Explanation

Mode – Select Hymn or Prelude

Hymn number – Select Hymn number

Next Intro, Verse Select to play introduction or verse

Play Mode [S]

VAR. Prelude begins at a random selection and plays continuously

FIXED Prelude begins at a predetermined selection and plays continuously

Tempo 20–240 Tempo of the Hymn

Volume [S] 0%–100% The volume of the Hymn

Transpose -6–+5 Change the key of the song in semitone steps

Book [S] – Select Hymn book

Song Recorder

Recording, playing, saving, deleting, and copying song data

Menu item Value Explanation

Source

USB Play back song data from USB ash drive.

INTERNAL Play back song data from internal memory.

PRESET Play back built-in preset song (demo song).

Song Name of the song

Tempo Refer to “Beat” (p. 16) Tempo of the song

Measure Measure of the song

[Division Mute] Refer to “Muting a Specic Division During Playback” and “Playing Back a Specic Division as a Guide Tone” (p. 31).

Swell MUTE, GUIDE, PLAY

Select the division that you want to mute.

Great MUTE, GUIDE, PLAY

Choir (3-manual

model only)

MUTE, GUIDE, PLAY

Pedal MUTE, GUIDE, PLAY

Guide Volume [S] 1–10 Adjust the volume of the guide tone.

Guide Tone [S]

F16, P16, R16, F8, P8,

R8, F4, P4, R4

F: Flute,

P: Principal,

R: Reed,

Number: Footage

Choose the guide tone.

Playback

Transpose

-6–+5 The transpose function lets you shift the pitch in semitone steps.

Play Mode

OFF Play back only the selected song.

CHAIN Consecutively play back all the songs on the selected media.

Metronome

Volume

OFF, 1–10 Volume of the metronome. Turn this “OFF” if you don’t want the metronome to sound.

Beat

Beat of the song or metronome

The tempo range will vary depending on the Beat setting.

Beat Tempo range

2/2 10–120

0/4, 2/4, 3/4, 4/4, 5/4,

6/4, 7/4

20–240

3/8 40–480

6/8, 9/8, 12/8 13–160

[Save Song] Refer to “Saving a Recorded Song” (p. 32).

[Delete Song] Refer to “Deleting a Recorded Song” (p. 33).

[Copy Song] Refer to “Copying a Saved Song” (p. 34).

Making Settings in the Menus

Pitch/Tuning

Settings for pitch, Temperament, Tuning, and Transpose

Menu item Value Explanation

Pitch

The reference pitch can be changed from “A=440.0 Hz” to “A=415.0 Hz” (Baroque pitch) or “A=392.0 Hz” (Versailles pitch).

VERSAILLES 392 (Hz)

BAROQUE 415 (Hz)

MODERN 440 (Hz)

VENETIAN 465 (Hz)

Temperament

Historical styles of music such as baroque can be played in the tunings that were used during that time.

EQUAL

(Equal temperament)

This temperament divides the octave into twelve equal intervals. Modulating to a dierent key will not aect the sonority of

the chords.

WERCK.

(Werckmeister)

This temperament combines the meantone temperament and the Pythagorean temperament. It allows playing in all keys

(method 1, number 3).

KIRN.1

(Kirnberger 1)

This is an improvement of meantone temperament and just intonation to allow greater freedom of modulation. It allows

playing in all keys (method 1).

KIRN.3

(Kirnberger 3)

This is a variation of Kirnberger 1 (method 3).

VALLO.

(Vallotti)

This is a relatively recent temperament. It is close to equal temperament but has a certain amount of just intonation, making

it easier to stay in tune with other instruments, and is thus frequently used for ensembles.

MEAN.D (Meantone

temperament)

This temperament is a partial compromise from just intonation in order to allow a certain degree of modulation. Preference

is given to the sonority in D#.

MEAN.E (Meantone

temperament)

This temperament is a partial compromise from just intonation in order to allow a certain degree of modulation. Preference

is given to the sonority in Eb.

PYTHG.

(Pythagorean tuning)

This is a system of tuning attributed to the philosopher Pythagoras, in which the fourth and fth are pure. Chords including

the third will not sound smooth, but the melody will sound good.

M.BACH

(Modern Bach)

This is one of the recently researched temperaments from the era of Bach. It allows playing in all keys.

Tuning 415.3–466.1 Hz You can adjust this in a range of 415.3–466.1 Hz (a semitone) centered on the selected pitch.

Transpose -6–+5

The transpose function lets you shift the pitch in semitone steps without changing the keys you play on the keyboard.

MEMO

From the main screen, while holding the [SET] piston, turn the [Value/Exit Menu] knob to change the transpose. From the main

screen, press the [0] piston to turn o transpose.

Room Modeling

Reverb settings

Menu item Value Explanation

Room Type [S]

By changing the type of reverberation you can experience the sensation of performing in a variety of locations.

CHAMBER The reverberation of a pipe chamber

HALL The reverberation of a hall

CHURCH The reverberation of a church

CATHEDRAL The reverberation of a cathedral

Wall Type [S]

You can make additional changes to the reverberation by changing the wall type (the material out of which the wall is constructed).

DRAPERY Pleated curtains

WOOD Wood

BRICK Brick

MARBLE Marble

Making Settings in the Menus

MIDI Coupler

MIDI coupler settings

Menu item Value Explanation

Division

SWELL A, SWELL B,

GREAT A, GREAT B,

CHOIR A (3-manual

model only),

CHOIR B (3-manual

model only),

PEDAL A, PEDAL B

Division

MIDI CH [V] [P] CH1–16 MIDI transmit channel

Name [V] [P] Name of sound Select by sound name (refer to “Tone Name [S]” (p. 22))

PC Number

[V] [P]

OFF, 001–128 Program change number

Bank MSB [V] [P] OFF, 000–127 Bank select MSB

Bank LSB [V] [P] OFF, 000–127 Bank select LSB

Volume [V] [P] OFF, 0–127 Species the volume

Octave [V] [P] -2–+2, NORMAL Species the octave (pitch)

Reverb [V] [P] OFF, 0–127 Species the depth of reverb

Chorus [V] [P] OFF, 0–127 Species the depth of chorus

Velocity [V] [P]

KBD The keyboard’s velocity will be used

EXP The expression pedal’s position will be used

2–127 The specied value will be used as the velocity

Expression [V] [P] OFF, ON Expression Pedal

About MIDI transmit channels

When the [MIDI] coupler is on

To avoid a conict between the MIDI transmit channels of the various

[MIDI] couplers, the MIDI transmit channels are xed as follows.

Division Piston name MIDI transmit channel

CHOIR

MIDI A CH4 (xed)

MIDI B CH8 (xed)

GREAT

MIDI A CH1–CH16

MIDI B CH5 (xed)

SWELL

MIDI A CH2 (xed)

MIDI B CH6 (xed)

PEDAL (pedalboard)

MIDI A CH3 (xed)

MIDI B CH7 (xed)

When the [MIDI] coupler is o

Even when the [MIDI] coupler is o, the performance data from each

division is transmitted on the following MIDI channels.

As appropriate, you’ll need to change the MIDI reception settings on

the MIDI device that’s connected.

Division MIDI transmit channel

CHOIR CH15 (xed)

GREAT CH12 (xed)

SWELL CH13 (xed)

PEDAL (pedalboard) CH14 (xed)

 When using a [MIDI] coupler to control an external MIDI sound module,

we recommend that you set your external MIDI device to not receive

messages on channels 12–15.

Making Settings in the Menus

Console

• Screen contrast

• MEL and BASS coupler settings, and other settings

Menu item Value Explanation

Display Contrast

[S]

0–30

Adjust the Display Contrast

 This setting will return to the default value when you turn o the power, but you can store the setting so that it will be

remembered even after the power is turned o. For details, refer to “Storing Your Settings (Customize)” (p. 24).

Bass Split [S]

You are free to change the range in which the bass coupler will operate. The specied note and those below it will use the bass coupler.

Top key of the Bass coupler range

Bass coupler

Mel SW Split [S]

Mel CH Split [S]

Mel SO Split [S]

You are free to change the range in which the melody coupler will operate. The specied note and those above it will use the melody coupler, and

notes below it will not.

Melody coupler

Bottom key of the Melody coupler range

Blind [S]

BLIND When the [TUTTI] piston is pressed or Crescendo pedal is activated, stop illumination is turned o.

VISIBLE When the [TUTTI] piston is pressed or Crescendo pedal is activated, stop illumination is turned on.

OPERATE

When the [TUTTI] piston is pressed or Crescendo pedal is activated, stop illumination is turned on.

Also you can operate the stops.

Auto O [S]

OFF, 10 min, 30 min,

240 min

If this is set to “240 min,” the power will automatically turn o 240 minutes after the Organ was last operated.

NOTE

After Auto O shut down, turn the power switch o. Wait at least ve seconds, then turn the power switch on again.

WARNING

With the factory settings, the power will automatically be switched o 240 minutes after you stop playing or operating the unit.

If you don’t want the unit to turn o automatically, change the “Auto O” setting to “OFF.”

Music Rest Lamp [S]

OFF, 1–16 Setting Music Rest and Pedalboard Lamp brightness.

Piston lamp [S] 1–16 Setting Piston Tablet Stop Lamp brightness.

Keyboard Type

[S]

NORMAL Non-Tracker Keyboard

TRACKER Tracker Keyboard

Keyboard Sens

[S]

LIGHT, NORMAL,

HEAVY

Keyboard Touch

Pedal Sens [S]

LIGHT, NORMAL,

HEAVY, FIX 127,

FIX 100, FIX 80

Pedalboard Touch

PD/GT Piston Cplr

OFF, ON Synchronizes PEDAL and GREAT Division Memory Pistons.

Making Settings in the Menus

Tremulant

The tremulant eect adds vibrato (cyclic modulation) to the sound.

Menu item Value Explanation

Division

SWELL MAIN Sets the tremulant for SWELL MAIN.

SWELL MAIN2 Sets the tremulant for SWELL MAIN2.

SWELL FLUTE Sets the tremulant for SWELL FLUTE.

SWELL FLUTE2 Sets the tremulant for SWELL FLUTE2.

GREAT MAIN Sets the tremulant for GREAT MAIN.

GREAT MAIN2 Sets the tremulant for GREAT MAIN2.

GREAT FLUTE Sets the tremulant for GREAT FLUTE.

GREAT FLUTE2 Sets the tremulant for GREAT FLUTE2.

CHOIR MAIN

(3-manual model only)

Sets the tremulant for CHOIR MAIN.

CHOIR MAIN2

(3-manual model only)

Sets the tremulant for CHOIR MAIN2.

CHOIR FLUTE

(3-manual model only)

Sets the tremulant for CHOIR FLUTE .

CHOIR FLUTE2

(3-manual model only)

Sets the tremulant for CHOIR FLUTE2.

SOLO MAIN Sets the tremulant for SOLO MAIN.

SOLO MAIN2 Sets the tremulant for SOLO MAIN2.

SOLO FLUTE Sets the tremulant for SOLO FLUTE.

SOLO FLUTE2 Sets the tremulant for SOLO FLUTE2.

Depth [S] 0–127 With a setting of “0,” no tremulant will be applied. Increasing this value will make the tremulant deeper.

Rate [S] 0–127 A slow tremulant will be applied with a setting of “0,” and this will become faster as you increase the value.

Exp. Pedal

Expression pedal settings

Menu item Value Explanation

Great/Pedal [P]

OFF Not aected by the expression pedal

ON GREAT and Pedal division are aected by the expression pedal

SWELL [P]

OFF Not aected by the expression pedal

ON SWELL division is aected by the expression pedal

Shutter [S]

You can adjust the minimum volume that will be in eect when the expression pedal is at the minimum position.

PPPP Least volume

PPP Low volume

PP Somewhat higher volume

UNENCL Not aected by the expression pedal

Kick SW [S]

The kick switch is located on the side of the expression pedal. You can assign a function to the kick switch.

OFF The kick switch will be o.

This has the same function as the [NEXT] piston. It will switch to the next general memory piston. Each time you press the

kick switch, the general memory piston will switch to the next higher number.

This has the same function as the [PREV] piston. It will switch to the previous general memory piston. Each time you press

the kick switch, the general memory piston will switch to the next lower number.

SUSTAIN

Sustain will be applied while you are pressing the switch.

 Sustain can be applied only to some of the Stop Library coupler sounds and to the sounds of an external MIDI sound module.

 Sustain will not be applied to the sounds of the organ.

Page is loading ...

Rodgers Infinity organ Owner's manual

Brand: Rodgers

Model: Infinity organ

Category: Supplementary music equipment

Type: Owner's manual

Download PDF

report

Rodgers Infinity organ Owner's manual

Rodgers Infinity organ Owner's manual

Related papers

Other documents