Nissan Murano Reference guide

Category
Cars
Type
Reference guide
QUICK REFERENCE GUIDE
2020 MURANO
Behind
steering
wheel
COCKPIT OVERVIEW
COCKPIT OVERVIEW
Headlight and Turn Signal Switch
Vehicle Information Display
Low Tire Pressure Warning Light
Wiper and Washer Switch
Steering Wheel Switches for Audio/Bluetooth®/Navigation/
Vehicle Information Display
Cruise Control/Intelligent Cruise Control
Instrument Brightness Control
Twin Trip Odometer Reset Switch
Heated Steering Wheel Switch
Vehicle Dynamic Control (VDC) OFF Switch
OFF
Power Liftgate Switch
Dynamic Driver Assistance Switch
Tilt/Telescopic Steering Column
INSTRUMENT PANEL
Fuel-ller Door Release
Hood Release
Control Display/Navigation/Audio System
Heater and Air Conditioner (automatic)
Front Passenger Air Bag Status Light
Push-button Ignition Switch
USB Ports/AUX Input Jack
Power Outlet
INSTRUMENT PANEL
Please see your Owner’s Manual for important safety information and system operation limitations.
A cellular telephone should not be used for any purpose while driving so full attention may be
given to vehicle operation.
Always wear your seat belt.
Supplemental air bags do not replace proper seat belt usage.
Children 12 and under should always ride in the rear seat properly secured in child restraints or
seat belts according to their age and weight.
Do not drink and drive.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)”, the “Monitor, climate, audio, phone, and voice recognition systems (section 4)” and the
Starting and driving (section 5)” of your Owner’s Manual.
Additional information about your vehicle is also available in your Owner’s Manual,
NissanConnect
®
Owner’s Manual and at www.NissanUSA.com.
GETTING STARTED
Nissan Intelligent Key® System ........................................................3
Seat Adjustments ......................................................................5
Automatic Drive Positioner (if so equipped) ...........................................6
Rear Door Alert.........................................................................7
Starting/Stopping the Engine .........................................................8
Outside Mirror Control Switch .........................................................8
HomeLink® Universal Transceiver (if so equipped).....................................9
E-Call (SOS) Button (if so equipped) ..................................................10
Heater and Air Conditioner (automatic) ..............................................10
Heated Steering Wheel (if so equipped)...............................................12
Headlight Control Switch .............................................................12
Wiper and Washer Switch .............................................................13
Vehicle Information Display...........................................................14
Tire Pressure Monitoring System (TPMS) with Easy-Fill Tire Alert ....................15
Loose Fuel Cap and Fuel-ller Door...................................................16
Towing Your Vehicle...................................................................17
Power Liftgate (if so equipped) .......................................................17
Motion-Activated Liftgate (if so equipped) ...........................................18
Front Armrest/Center Console Storage Box..........................................18
AUDIO, NAVIGATION AND BLUETOOTH® FEATURES
How to Use Your Murano’s Touch-screen Display ....................................19
Clock Set/Adjustment ................................................................20
USB (Universal Serial Bus) Connection Ports/AUX Input Jack and iPod® Interface ....20
Bluetooth® Hands-free Phone System ...............................................21
• System Operating Tips ...........................................................21
FM/AM/SiriusXM® Radio with CD Player ..............................................23
Apple CarPlay® .......................................................................24
Android Auto™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Navigation System (if so equipped)...................................................26
SiriusXM® Travel Link and SiriusXM® Trac (if so equipped) ..........................28
NissanConnect® Services Powered by SiriusXM® (if so equipped)....................28
Hands-free Text Messaging Assistant ............................................... 30
Bluetooth® Streaming Audio..........................................................31
TABLE OF CONTENTS
TABLE OF CONTENTS
DRIVING FEATURES
Blind Spot Warning (BSW) with Rear Cross Trac Alert (RCTA) (if so equipped) ......32
Intelligent Cruise Control (ICC) (if so equipped).......................................32
Cruise Control (if so equipped)........................................................33
Automatic Emergency Braking (AEB) (if so equipped) ................................34
Automatic Emergency Braking (AEB) with Pedestrian Detection System
(if so equipped)........................................................................34
Intelligent Around View Monitor (if so equipped) .....................................35
Hill Start Assist ........................................................................36
Rear Automatic Braking (RAB) (if so equipped) .......................................37
Lane Departure Warning (LDW) and Intelligent Lane Intervention (I-LI)
(if so equipped)........................................................................37
Intelligent Driver Alertness (I-DA) .....................................................38
Intelligent Forward Collision Warning (I-FCW) ........................................38
Vehicle Dynamic Control (VDC) .......................................................39
Trac Sign Recognition (TSR) (if so equipped)........................................39
Please see your Owner’s Manual for important safety information and system operation limitations.
A cellular telephone should not be used for any purpose while driving so full attention may be
given to vehicle operation.
Always wear your seat belt.
Supplemental air bags do not replace proper seat belt usage.
Children 12 and under should always ride in the rear seat properly secured in child restraints or
seat belts according to their age and weight.
Do not drink and drive.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system
(section 1)”, the “Monitor, climate, audio, phone, and voice recognition systems (section 4)” and the
Starting and driving (section 5)” of your Owner’s Manual.
Additional information about your vehicle is also available in your Owner’s Manual,
NissanConnect
®
Owner’s Manual and at www.NissanUSA.com.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
3
NISSAN INTELLIGENT KEY® SYSTEM
The Nissan Intelligent Key® system allows you to lock or unlock your vehicle, open
your liftgate (if so equipped) and start the engine. It is important to make sure the
Intelligent Key is with you (that is, in your pocket or purse).
KEY-LINKED SYSTEM (if so equipped)
The Key-Linked System indicates which
Intelligent Key is being recognized in the
vehicle information system.
The Key-Linked System can be turned on or
o through the vehicle information display
“Settings” screen .
A maximum of four Intelligent Keys can be set
to the Key-Linked System.
When the system is enabled, the recognized
Intelligent Key is displayed at engine start-
up (engine ON) as well as within the vehicle
information display “Settings” screen .
When the system is active, the vehicle
information display setting items are
memorized for each key that has been
enabled in the Key-Linked System.
If two Intelligent Keys are in the vehicle, the Key-Linked System will recognize
the key that was used most recently; this usually means the last key to
unlock/lock the door.
If there is a desire to change to another Intelligent Key that is in the vehicle, the
user must turn o the engine and initiate communication from the desired key.
1. Turn the engine to OFF.
2. Press the button from the desired Intelligent Key.
3. Start the engine.
4. The desired Key Number recognized should appear on the vehicle
information display.
The vehicle information display shows a pop-up notication at engine ON for
the recognition of the system.
When enabled, the Key-Linked System will remember the state of the items
memorized automatically from the last ignition cycle.
REMOTE ENGINE START WITH INTELLIGENT CLIMATE CONTROL* (if so equipped)
The Remote Engine Start operating range is approximately 197 ft (60 m) from
the vehicle. The eective operating range may be shorter if there are walls,
strong radio wave sources near the operating location or other obstructions
between the key and the vehicle.
GETTING STARTED
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
4
For the Remote Engine Start to function, the vehicle must be in
the P (PARK) position with the ignition o and all doors must
be closed and locked. Please see your Owner’s Manual for
additional information.
To start your vehicle remotely:
1. Press the button to lock all doors.
2. Within 5 seconds, press and hold the Remote Engine Start
button for at least 2 seconds.
The engine will start, and the parking lights will turn on.
The automatic climate control system will begin heating or
cooling the vehicle depending on the outside (ambient) temperature, cabin (in-
car) temperature and the last user mode. During this period, the climate control
display and buttons will be inoperable until the ignition switch is turned ON.
The engine will run for 10 mˆinutes and then turn o.
Repeat steps 1 and 2 to extend the time for an additional 10-minute period.
Remote Engine Start can only be activated for a maximum of 20 minutes.
After two Remote Engine Starts, the ignition switch must be cycled before the
Remote Engine Start can be used again.
To cancel the Remote Engine Start, press the Remote Engine Start button .
To start driving, depress the brake pedal and push the ignition switch.
LOCKING AND UNLOCKING THE VEHICLE
The operating range of the Intelligent Key is within 31.5 in (80 cm) from each
request switch.
To lock the vehicle, either push the door handle request switch once or press
the button on the key fob.
To unlock the vehicle, perform one of the
following procedures:
Push either door handle request switch
once to unlock the corresponding door.
Push the door handle request switch
again within 1 minute to unlock all doors, or
Press the button on the key fob to
unlock the driver’s side door. Press the
button again within 1 minute to unlock all doors.
The Intelligent Key can also be used to activate the panic alarm by pressing
and holding the button for 1 second. Once activated, the panic alarm and
headlights will stay on for a period of time.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
5
SEAT ADJUSTMENTS
FRONT POWER SEATS (if so equipped)
To slide the seat forward or backward, push the switch
forward or backward.
To recline the seatback, push the switch forward or backward.
FRONT POWER SEAT LIFTER (driver’s seat
if so equipped)
To adjust the angle of the front seat cushion
or height of the seat, push the front or rear
end of the switch up or down.
FRONT LUMBAR SUPPORT (driver’s seat
if so equipped)
To adjust the seat lumbar support, push the
front or back end of the switch .
FOLDING DOWN THE REAR SEAT
To fold the seats at, release the connector
tongue of the rear center seat belt from
the buckle then store the connector and
seat belt tongues in the retractor base
on the ceiling .
Fold the seatback forward using either the
reclining strap , located on the outside
edge of the rear seat, or the release lever
in the cargo area.
NISSAN INTELLIGENT KEY® BATTERY DISCHARGE
If the battery of the Intelligent Key is
discharged or environmental conditions
interfere with the Intelligent Key
operation,
Key Battery Low will
display on the gauge and the engine will need to be started according to the
following procedure:
1. Move the shift lever to the P (Park) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key. A chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while
depressing the brake pedal and the engine will start.
*State laws may apply; review local laws before using.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)”, the “Pre-driving checks and
adjustments (section 3)”, the “Monitor, climate, audio, phone, and voice recognition systems (section 4),
and the Starting and driving (section 5)” of your Owner’s Manual.
Key Battery Low
GETTING STARTED
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
6
To raise the seatback manually, lift up each seatback and push it to the upright
position until it is latched.
RECLINING THE REAR SEATS
Brace the back of the seat with your arm while pulling on the strap. The
seatback will release quickly.
Pull the reclining strap , and move the seatback to the desired angle.
Release the reclining strap after positioning the seat at the desired angle.
CLIMATE CONTROLLED SEATS (if so equipped)
The climate-controlled seat warms up or cools
down the front seat by blowing warm or cool air
from under the surface of the seat. To adjust the
temperature of the climate controlled seat:
Turn the knobs to the left to cool the seat
or to the right to heat the seat.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Safety – Seats, seat belts and supplemental restraint system
(section 1)” and the Instruments and controls (section 2) of your Owner’s Manual.
AUTOMATIC DRIVE POSITIONER (if so equipped)
Automatic Drive Positioner provides two methods for storing the driver’s seat,
steering column (if so equipped) and outside mirror positions. Once enabled,
the Key-Linked System automatically retains the driver’s last positions for the
specic Intelligent Key when the ignition switch is turned from ON to OFF. The
Automatic Drive Positioner switch can store two additional positions which are
independent from the Key-Linked System.
KEY-LINKED SYSTEM
Use the following process to set up
Key-Linked System:
Unlock the vehicle with the desired
Intelligent Key while the ignition is OFF.
Place the ignition in the ON position.
Within the “Settings” menu of the
vehicle information display and select
“Key-Linked Settings” .
Press the OK button on the steering wheel
to turn the system ON/OFF .
Every time ignition is turned from ON to OFF,
the memory positions of the driver’s seat,
automatic steering wheel (if so equipped)
and outside mirrors are linked to the
Intelligent Key.
Follow the same procedure if you want to link a 2
nd
, 3
rd
or 4
th
Intelligent Key.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
7
GETTING STARTED
AUTOMATIC DRIVE POSITIONER SWITCHES
In addition to the Key-Linked System
feature, two additional driver preferences
can be saved using the memory
switches 1 and 2 .
Use the following process to store the
memory positions:
The vehicle should be stopped while
setting the memory.
Adjust the driver’s seat, steering column (if
so equipped) and outside mirrors to the desired positions using the adjustment
switches for each feature.
Push the SET switch , and within 5 seconds, push the memory
switch 1 or 2 .
The indicator light for the selected switch will illuminate for 5 seconds and a
chime will sound indicating the memory has been successfully stored.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
REAR DOOR ALERT
The Rear Door Alert functions under certain conditions to indicate there may be an
object or passenger in the rear seat(s). The system is activated when a rear door is
opened and closed within 10 minutes of the vehicle being started.
REAR DOOR ALERT (ACTIVE)
When the system is active, the horn will
sound three times twice and a Check Rear
Seat For All Articles warning will appear
on the display.
To activate Rear Door Alert, in your vehicle
information display:
Press the buttons on the
steering wheel until the “Settings” menu
screen appears.
Using the buttons, select “Vehicle Settings”,
“Rear Door Alert” and press the OK button.
Choose from the following options: “OFF”,
“Horn & Alert” or “Alert Only”, and then
press the OK button.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
8
To Dismiss Rear Door Alert:
To dismiss the warning, use the buttons
on the steering wheel to select “Dismiss
Message” . If no selection is made,
this message will disappear after a
period of time.
To temporarily disable Rear Door Alert for the
remainder of the current trip, use the buttons on the steering wheel to select
“Disable Alert” and press the OK button.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
STARTING/STOPPING THE ENGINE
It is important to make sure the Nissan
Intelligent Key® is with you (that is, in your
pocket or purse).
Depress the brake pedal.
Push the ignition switch to start the engine.
TURNING THE ENGINE OFF
Move the shift lever to the P (Park) position.
Push the ignition switch to turn
the engine o.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the Starting and driving (section 5)” of your Owner’s Manual.
OUTSIDE MIRROR CONTROL SWITCH
To select the right or left side mirror, push the
small switch right or left.
To adjust the mirror angle, push the large
switch up, down, right or left.
To prevent accidentally moving the
mirror, push the switch to the center
(neutral) position.
REVERSE TILT-DOWN FEATURE (if so equipped)
The reverse tilt-down feature will turn both outside mirror surfaces downward to
provide better rear visibility close to the vehicle.
1. Apply the brake.
2. Place the ignition switch in the ON position.
3. Move the shift lever to the R (Reverse) position.
4. Both outside mirror surfaces will turn downward. (The mirror control switch
must be out of the center [neutral] position.)
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
9
HOMELINK
HOMELINK® UNIVERSAL TRANSCEIVER (if so equipped)
The HomeLink® Universal Transceiver can learn and consolidate the functions
of up to three dierent hand-held transmitters, operating items such as garage
doors, property gates, outdoor and indoor lights or alarm systems.
Place the ignition switch in the ON or ACC position (without starting the engine)
when programming Homelink.
To program the HomeLink Universal Transceiver:
Position the handheld transceiver 1-3 in (2-8 cm) away from the HomeLink
surface, keeping the HomeLink indicator light in view.
Press and hold the desired HomeLink button and the handheld transmitter
button simultaneously until the HomeLink indicator light ashes slowly and
then rapidly.
Both buttons may be released when the indicator light ashes rapidly.
To verify the programing is complete, press and hold the HomeLink button and
observe the indicator light:
A solid, continuous light indicates the programing is complete and the
HomeLink button will activate your device.
A blinking light that turns to a solid, continuous light after 2 seconds indicates
additional steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete the
programing process:
At the receiver of the device that you are programing to the HomeLink
button, press and release the learn or smart button (the name may vary by
manufacturer, but it is usually located near where the hanging antenna wire
is attached to the unit). You have approximately 30 seconds to initiate the
following step.
The outside mirror surfaces will return to their original positions when one of the
following conditions has occurred:
The shift lever is moved to any position other than R (Reverse).
The outside mirror control switch is set to the center (neutral) position.
The ignition switch is placed in the OFF position.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
GETTING STARTED
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
10
Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous two steps up to three times to complete
the programing process. HomeLink should now activate your device.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the
HomeLink website at www.homelink.com or call 1-800-355-3515.
E-CALL (SOS) BUTTON (if so equipped)
The E-call (SOS) feature requires a
NissanConnect® Services subscription.
With a paid subscription, it can be used to call
for assistance in case of an emergency.
To use this feature, press the
SOS button on the overhead console.
For additional information, or to enroll your vehicle, refer to
www.NissanUSA.com/connect or call 855-426-6628.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual or refer
to the “Information (section 5)” of your NissanConnect® Owner’s Manual.
HEATER AND AIR CONDITIONER (automatic)
AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL
The automatic mode may be used year-round. Press the AUTO button to
turn the system on, and the system will automatically control the inside
temperature (automatic cooling and/or dehumidied heating), air ow
distribution and fan speed.
Turn the driver’s side temperature control dial to the left for cooler air or to
the right for warmer air.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
11
DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Press the DUAL button to turn the passenger’s side temperature controls
on or o. This will allow the passenger’s side temperature to be adjusted
independently from the driver’s side by turning the passenger’s side
temperature control dial.
Turn the passenger’s side temperature control dial left for cooler air or right
for warmer air.
ON•OFF BUTTON
Press the button to turn the system on or o.
FAN SPEED CONTROL BUTTONS
Press either the or the button to decrease or increase fan speed.
MODE BUTTON
Press the MODE button to cycle through the following air ow outlets:
Air ows from the center and side vents.
Air ows from the center, side and foot vents.
Air ows mainly from the foot vents.
Air ows from the front defroster and foot vents.
AIR RECIRCULATION CONTROL BUTTON
Press the air recirculation control button to recirculate interior air inside
the vehicle. The indicator light on the button will illuminate. This system
is used to avoid certain outside odors and to adjust the inside vehicle
temperature more eectively.
The air recirculation mode cannot be activated when the climate control
system is in the front defroster mode FRONT.
FRESH AIR INTAKE CONTROL BUTTON
Press the fresh air intake control button to draw outside air into
the passenger compartment. The indicator light on the
button will
illuminate and the indicator light on the button will extinguish.
DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS
Press the front defroster FRONT button to turn the system on. This
feature removes humidity from the air.
Turn the temperature control dial to set the desired temperature.
To defrost the front and side windows quickly, set the temperature controls
and fan speed controls to their maximum settings.
DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS (if so equipped)
Push the rear window defroster REAR switch to turn the system on or o.
This function automatically turns o after approximately 15 minutes.
A/C BUTTON
Press the A/C button to turn the air conditioner system on or o. This system
helps cool and dehumidify the air inside the cabin and defog the windows.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” and the “Monitor, climate,
audio, phone, and voice recognition systems (section 4)” of your Owner’s Manual.
GETTING STARTED
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
12
HEATED STEERING WHEEL (if so equipped)
Push the switch to turn on the
heated steering wheel
The heated steering wheel will automatically
turns o and on to maintain a temperature
above 68°F (20°C).
Push the switch to turn the
heated steering o.
If the temperature of the steering wheel is above 68°F (20°C), the system will not
heat the wheel.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the Instruments and controls (section 2) of your Owner’s Manual.
HEADLIGHT CONTROL SWITCH
HEADLIGHT CONTROL
Turn the headlight control switch to
the position to turn on the front
parking, side marker, tail, license plate and
instrument panel lights. Turn the switch to
the position to turn on the headlights.
AUTOLIGHT SYSTEM
The autolight system will automatically turn the headlights on when it is dark
and o when it is light. The system will keep the headlights on for a period of
time after you turn the ignition o and all doors are closed.
To activate the autolight system, turn the headlight control switch to the
AUTO position then place the ignition switch in the ON position. To
deactivate the autolight system, turn the headlight control switch to the
OFF position, position or position .
HEADLIGHT BEAM SELECT
With the headlights ON (by selecting the
position ), push the headlight control
switch forward to select the high beam
function. The blue indicator light will
illuminate in the instrument panel. Pull the
headlight switch back to the original position
to select the low beam. The blue indicator
light will extinguish.
Pull and release the headlight control switch to ash the headlight high
beams on and o.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
13
HIGH BEAM ASSIST (if so equipped)
To activate the High Beam Assist system, turn the headlight switch to the
AUTO position and push the lever forward . The High Beam Assist
indicator light in the meter will illuminate while the headlights are turned on.
When the vehicle speed lowers to less than approximately 25 mph (40 km/h),
the headlight uses the low beam.
To turn o the High Beam Assist system, turn the headlight switch to the
position or select the low beam position by placing the lever in the
neutral position.
FOG LIGHT SWITCH (if so equipped)
The headlights must be on and the
low beams selected for the fog
lights to operate.
Turn the switch (inside collar) to the
position to turn the fog lights on.
Turn the switch (inside collar) to
the OFF position to turn the fog lights o.
LANE CHANGE SIGNAL
Move the lever up or down until the turn signal begins to ash but the
lever does not latch to signal a lane change. Hold the lever until the lane
change is completed.
Move the lever up or down until the turn signal begins to ash but the
lever does not latch and release the lever. The turn signal will automatically
ash three times.
Choose the appropriate method to signal a lane change based on the road and
trac conditions.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
WIPER AND WASHER SWITCH
Move the lever to one of the following positions to operate the
windshield wipers:
Mist (MIST) – One sweep operation of
the front wipers.
Intermittent (INT) – Operates the
speed-sensing (if so equipped) wipers
intermittently. The intermittent speed
can be adjusted by twisting the time
control ring
to increase or decrease
wiper sensitivity.
Low (LO) – Front wipers operate at a
continuous low-speed.
High (HI) – Front wipers operate at a continuous high-speed.
MIST
OFF
INT
LO
HI
GETTING STARTED
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
14
INT
ON
Pull the lever toward you to activate
the front washer. The front wipers will
operate several times.
REAR WIPER AND WASHER
Intermittent (INT) – Rear wiper operates
intermittently.
Low (ON) – Rear wiper operates at a
continuous low-speed.
Push the lever forward to activate
the rear washer. The rear wiper will
operate several times.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
VEHICLE INFORMATION DISPLAY
When the buttons on the steering
wheel are pressed, the following screens will
appear on the vehicle information display :
Home – Displays the current speed,
the compass and the additional media
that is available.
Audio – Displays the current playing
media. Press the OK button on the
steering wheel to select other media sources.
Navigation (if so equipped) – Displays the vehicle’s current direction.
Drive Computer – Displays Average Fuel Economy, Average Speed, Trip
Computer and Time of the Trip. Press and hold the OK button on the
steering wheel to reset.
To view detailed instructional videos regarding these and other features,
please go to www.nissanownersinfo.mobi.
15
Fuel Economy – Displays Average Fuel Economy. Press and hold the
OK button on the steering wheel to reset.
Driving Aids (if so equipped) – Displays the Driving Aids that are equipped
on your vehicle. Use the OK button on the steering wheel to turn each
system on or o.
Speed Limit Sign (if so equipped) - Provides the driver with information
regarding the most recently detected speed limit.
Tire Pressure Information – Displays the individual tire
pressures while driving.
Warning Review– Displays the current warnings.
Settings – Displays the available settings that can be changed.
Press the OK button on the steering wheel to choose
the selected menu.
Press the buttons on the steering wheel to cycle through the
various setting modes.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
GETTING STARTED
TIRE PRESSURE MONITORING SYSTEM (TPMS) WITH
EASY-FILL TIRE ALERT
The low tire pressure warning light and a Tire Pressure Low - Add
Air warning will illuminate when one or more tires are low in pressure
and air is needed.
Current tire pressure of all tires (except the spare) may be visible on the Tire
Pressure screen within the vehicle information display when the vehicle is driven
at speeds above 16 mph (25 km/h).
Adjust the tire pressure to the recommended tire pressure shown on the Tire
and Loading Information label located in the driver’s door opening.
When the low tire pressure warning light ashes for approximately 1 minute
and then remains on, the TPMS is not functioning properly. It is recommended
that you have the system checked by a Nissan dealer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

Nissan Murano Reference guide

Category
Cars
Type
Reference guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI