American Standard TU722508.013 Installation guide

American Standard
Brand
American Standard
Model
TU722508.013
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2020
Thank you for selecting American Standard...
the benchmark of ne quality for over 100 years.
RECOMMENDED TOOLS
M965928 Rev. 1.1 (3/20)
ROUGHING-IN DIMENSIONS
Estate
®
Pressure Balancing
Bath and Shower Trim Kit
INSTALLATION
INSTRUCTIONS
TU722500
TU722501
TU722502
TU722507
TU722508
Plumbers’ Putty
or Caulking
Adjustable Wrench Channel Locks
Phillips Screwdriver
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
OFF
Teon Tape
Flat Blade Screwdriver
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" (1879 mm)
FOR HEAD
CLEARANCE
3-3/4"
(97 mm)
2" TO 3"
(51 TO 76 mm)
18" (457 mm)
OPTIONAL
7-1/16"
(179 mm)
7-5/8"
(207 mm)
1/2" NPT
1/2" COPPER
FOR SLIP-ON
SPOUT
7-13/16" DIA.
(198 mm)
1-1/2"
4-11/16"
(121 mm)
7-3/8"
(187 mm)
9-1/2"
(223 mm)
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78"
(1651 AND 1981 mm)
7"
(160 mm)
2-3/4"
(83 mm)
2-3/4" MAX. (69 mm)
1-3/4" MIN. (45 mm)
5"
(127 mm)
CARTRIDGE INSTALLATION
11
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
For use with shower heads rated at 4.9 L/min (1.3 gpm) or higher.
• Remove PLASTER GUARD (6)
(Keep it installed for thin wall Installation).
• Remove BONNET NUT (1) by unthreading it
Counter clockwise. Remove test CAP (2).
• Remove PROTECTIVE HOUSING (3) from
CARTRIDGE (4). Install with “UP” text on top.
• Reinstall BONNET NUT (1) onto VALVE BODY (5)
and tighten rmly with 12 Nm or 9 lbs/ft.
1
2
6
5
3
4
UP
UP
NOTE: Specied tightening torque
of BONNET NUT (1) is critical to
assure sealing function.
- 2 -
UP
4
2
UP
1
1
2
UP
1
PLASTER
GUARD
Figure 2.
Figure 1.
Figure 1a.
1
Figure 2a.
4
3
C
H
4
3
C
H
2
4
• Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)
and tightening SET SCREW (3) from below with 2.5 mm
Hex Wrench supplied.
HANDLE INSTALLATION
M965928 Rev. 1.1 (3/20)
3
INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
• Remove pipe cap and plug from shower and tub rough piping.
• Slip DECORATIVE PLATE (5), then slip TUB SPOUT (1) onto tub nipple
and tighten with 4mm Hex Wrench.
CAUTION: Protect nish on TUB SPOUT when installing.
• Install SHOWER ESCUTCHEON (2) onto SHOWER ARM (3). Apply sealant
or Teon tape to threads on both ends of SHOWER ARM (3) and thread
longer leg of SHOWER ARM (3) into shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect nish on SHOWER HEAD and ARM when installing.
CAUTION
Protect nish on SHOWER HEAD
and TUB SPOUT when installing.
PIPE
PLUG
PIPE
CAP
4
3
2
SHR.
ELBOW
TUB FILLER
NIPPLE
1-1/2" REF.
2.5 MM HEX
WRENCH
1
5
OFF
1
2.5MM HEX
WRENCH
3
2
OFF
• Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
THIN WALL INSTALLATION
• Figure 1a. Push CAP (1) over VALVE CARTRIDGE (2) until
seated against stop.
• Figure 2a. Push ESCUTCHEON (3) onto CAP (1) and attach
to valve body with LONG SCREWS (4).
STANDARD WALL INSTALLATION
- 3 -
M965928 Rev. 1.1 (3/20)
COLDER
(Larger Numbers)
1 2 3 4 5 6 7 8 9 10
HOTTER
(Smaller Numbers)
1 2 3 4 5 6 7 8 9 10
3
4
1
5
2
7
5
• By restricting HANDLE rotation and limiting the amount of hot water
allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1)
reduces risk of accidental scalding. To set the maximum hot water
temperature of your faucet valve, adjust the setting on the HOT LIMIT
SAFETY STOP (1).
• Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before
making adjustment to HOT LIMIT STOP (1). Pull forward and rotate
counterclockwise one number to limit hot water temperature.
Use NUMBERS (5) on CARTRIDGE (4) on HOT LIMIT STOP (1)
for indication.
ADJUST HOT LIMIT STOP
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
6
VALVE LEAKS WHEN SHUT OFF
• Remove CARTRIDGE, see STEP 1 and STEP 2 and REVERSE
process.
• Clean SEALS on the side of CARTRIDGE. Clean inside sealing
surface of VALVE BODY.
• Re-assemble CARTRIDGE. Install trim. Turn on water supply and
check for leaks.
REPLACING CARTRIDGE
• To remove CARTRIDGE (1), install split WASHER (3) between the
ridge on the cartridge and the bonnet nut.
(only supplied with replacement cartridge). as shown.
• Proceed to unthread BONNET NUT (2) counter clockwise.
Note: CARTRIDGE (1) should be pulling out while unthreading
BONNET NUT (2).
• Upon removal of the old Cartridge, install a new cartridge
and secure it with BONNET NUT (Hand tighten).
BACK TO BACK INSTALLATION
• Remove CARTRIDGE (B) as detailed in steps above.
• Remove PIN (A) from CARTRIDGE (B) by pulling.
• Separate MANIFOLD (C) from CARTRIDGE (B) by pulling.
• Rotate CARTRIDGE (B) 180 degrees and reinstall MANIFOLD (C)
with PIN (A).
• The “UP” TEXT (D) should now be facing downward during
installation of the CARTRIDGE (B).
• Remove HANDLE (see step 3 and reverse).
• Remove ESCUTCHEON and CARTRIDGE CAP (see step 1 and reverse).
SERVICE
TO GAIN ACCESS TO VALVE FOR SERVICING
CAUTION
Turn off hot and cold water
supplies before beginning.
1
3
2
B
A
B
C
180º
B
A
B
D
1 2
3 4
BACK TO BACK INSTALLATION
Standard
Back to Back
- 4 -- 4 -
M965928 Rev. 1.1 (3/20)
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
M970092-YYY0A
Shower Arm & Flange
1660739.YYY
Shower Head
(2.5 gpm)
1660738.YYY
Shower Head
(1.75 gpm)
M907858-YYY0A
Escutcheon
M907414-YYY0A
Decorative Ring
M907050-YYY0A
Cover
M970093-YYY0A
Handle Kit
8888101.YYY
Tub Spout
M970457-0070A
Adaptor Kit
078016-0020A
Escutcheon Screw
M970654-0070A
Cartridge
PURCHASE SEPARATELY
M970649-YYY0A
Deep Rough-in Kit
C
H
OFF
Estate
®
Pressure Balancing
Bath and Shower Trim Kit
MODEL NUMBER
TU722500
TU722501
TU722502
TU722507
TU722508
Replace the “YYY” with
appropriate nish code
POLISHED CHROME 002
POLISHED NICKEL 013
LEGACY BRONZE 278
BRUSHED NICKEL 295
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard TU722508.013 Installation guide

American Standard
Brand
American Standard
Model
TU722508.013
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents