SIP 05719 is a welding trolley designed to transport a welder, accessories, and a large gas cylinder. It features two wheels for easy maneuverability and is ideal for use in garages, engineering, and agricultural workshops. With a load capacity of 99 kg, it can safely accommodate the weight of a welder and its accessories. The trolley also includes a retaining strap and chain for securing the gas cylinder during transport.
WELDING TROLLEY MANUAL
05719
Please read this manual before using
1. Product Descripon
The welding trolley accommodates a welder, accessories & gas cylinder.
Equipped with two wheels, it is very easy to move the welder and large gas bole.
It is an ideal piece of equipment to use in garage, engineering & agricultural workshops.
2. Product Specicaon
Model Dimensions
D x W x H (mm)
Packing Dimensions
L x W x H (mm)
Weight
(kg / lbs)
Load Capacity
(Kg / lbs)
05719 550 x 490 x 1140 600 x 540 x 1190 16 / 35 99 / 218
3. Warning
1. Always use the trolley on a level surface. Compressed gas cylinders are dangerous
should they fall.
2. Never posion the trolley on an inclined surface. It may p over, causing damage and
possible injury.
3. Before using, make sure all fasteners are ght and cart is assembled as per the provid-
ed instrucon
1140m
490mm
550mm
370mm
200mm
4.Assembly
Contents:-
4. Keep instrucons safe for reference.
5. Always move the trolley by using the trolley handle. Never pull the trolley by the
welder, welding torch , leads etc as this may cause the trolley to p over.
6. Do not remove parts from the trolley whilst it is being moved.
7. Always chain the compressed gas cylinder securely with the chains provided.
8. Never weld on the compressed gas cylinder or this cart.
9. Failure to follow these warnings may result in property damage, personal or fatal
injury
5. Fing the wheels:
Lay trolley frame down with the handle poinng up.
Fit the axle through the chassis. Figs 1 & 2
Contents cont….
1 x Trolley Frame 2 x Wheels
1 x Wheel Axle 4 x Wheel Washers
2 x Split Pin 2 x Bole Chain
1 x Strap c/w Clips
Fig.2
Fig.1
Repeat for the other side of the axle.
6. Fing the retaining strap:
Follow steps in Figs 7, 8, 9, 10, 11, 12 & 13:
Fig.5 Fig.6
Fig.3 Fig.4
Fit Washers, Wheel & split pin. Figs 3, 4, 5 & 6:-
Fig.9 Fig.10
Fig.11 Fig.12
Fig.7 Fig.8
6. Fing the chain:
Fit the chain as shown in Figs 14 & 15:
Adjust to suit your bole size.
Fig.14 Fig.15
Fig.13
SIP Industrial Products Limited
Gelders Hall Road
Shepshed
Loughborough
Leicestershire
LE12 9NH
United Kingdom
FOR HELP OR ADVICE ON THIS
PRODUCT PLEASE CONTACT
YOUR DISTRIBUTOR, OR SIP DI-
RECTLY ON:
TEL: 01509 500400
EMAIL: sales@sip-group.com or
technical@sip-group.com
www.sip-group.com
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling.
Help to protect the environment, take the packaging to the local amenity p and place into the
appropriate recycling bin.
Never dispose of electrical equipment or baeries in with your domesc waste. If your supplier
oers a disposal facility please use it or alternavely use a recognised recycling agent. This will al-
low the recycling of raw materials and help protect the environment.
1
2
3
4
5
6
7
8
EWM Trolly 39-1.1 DG Operating Instructions Manual
Kleenmaid BBQ5BF Owner's manual
Gleason Reel I-132 I-Beam Festoon System Installation guide
Meridian Seed Titan 2SE, 4SE Seed Tender Operating instructions
Sealey MIGHTYMIG 150 Operating instructions
Sealey MIGHTYMIG150.V2 User manual
WIA Weldmatic 175 Owner's manual
WIA Weldmatic 175S Owner's manual