Article MYSEN 19903 Assembly Instructions

Brand
Article
Model
MYSEN 19903
Type
Assembly Instructions

This manual is also suitable for

Article MYSEN 19903 will help you reduce the risk of tip-over by attaching it to your wall. You will need a drill to install the brackets on the wall, which should take around 20 minutes. The box includes 4 brackets, 4 M4x17mm screws, 4 M8x51mm plugs, 4 M6x70mm screws, and 2 straps. Use the 8mm or 5/16" drill bit to drill holes in the wall, and then align the brackets on the unit with the brackets on the wall. Once you pull down the strap, it will snap and lock into place.

Article MYSEN 19903 will help you reduce the risk of tip-over by attaching it to your wall. You will need a drill to install the brackets on the wall, which should take around 20 minutes. The box includes 4 brackets, 4 M4x17mm screws, 4 M8x51mm plugs, 4 M6x70mm screws, and 2 straps. Use the 8mm or 5/16" drill bit to drill holes in the wall, and then align the brackets on the unit with the brackets on the wall. Once you pull down the strap, it will snap and lock into place.

Assembly Instructions
NERA
Cabinet
VERSION 1.0
ASSEMBLY INSTRUCTIONS
Read these instructions carefully and keep for future
reference. Refer to parts inventory for guidance, and
ensure you have all pieces before starting.
When assembling, place all parts on a soft, clean, and flat
surface such as a carpet to prevent scratches.
If you’re having diculty, our friendly Customer Care
team is always here to help. Call us at 1.888.746.3455
during business hours, email [email protected] or chat
live at article.com.
Page 2 of 13
15 min
1
PARTS INVENTORY
ID DESCRIPTION QTY
LEG FRAME 2
SHELF 2
M6 × 15MM BOLT 12
ALLEN KEY 1
SHELF PIN 8
TIME # OF PEOPLE DIFFICULTY
ANTI-TIP
Installation Required
NERA Cabinet
Page 3 of 13
×12
1
NERA Cabinet
Page 4 of 13NERA Cabinet
2
× 4
× 4
Page 5 of 13NERA Cabinet
3
Adjust levelers on
legs as needed.
!
Page 6 of 13
To unlock pull lever out.
4
NERA Cabinet
Page 7 of 13
To lock pull lever in.
5
NERA Cabinet
Page 8 of 13
+2.5
-2.5
6
NERA Cabinet
Page 9 of 13NERA Cabinet
DOOR ADJUSTMENT INSTRUCTIONS
During shipping, the doors of your cabinet may have
shifted slightly. This can easily be corrected by tightening
a few screws. Always start by adjusting the top hinge on
the aected door.
REQUIRED TOOL
7A
Page 10 of 13NERA Cabinet
7B
8
Serious or fatal crushing injuries can occur from furniture
tip-over. To help prevent tip-over:
• Install tip-over restraint provided.
• Do not set heavy objects on top of this product,
unless the product is specifically designed to
accomodate them.
• Never allow children to climb or hang on mirrors,
shelves, consoles, or cabinets with doors and/or
drawers.
Use of tip-over restraints may only reduce but not
eliminate, the risk of tip-over.
20 min
3
TIME
REQUIRED TOOL
# OF PEOPLE DIFFICULTY
PARTS INVENTORY
ID DESCRIPTION QTY
BRACKET 4
M4 × 17MM SCREW 4
M8 × 51MM PLUG 4
M6 × 70MM SCREW 4
STRAP 2
ANTI-TIP RESTRAINT INSTALLATION
Page 11 of 13
CABINET Anti-Tip Installation
WARNING!
Hardware (C/D) to attach brackets to wall is
designed for drywall. To attach this unit to another
type of wall, consult with your local hardware store.
REQUIRED TOOL
8MM / 5/16" DRILL BIT
1010 Raymur Ave.
Vancouver, BC V6A 3T2
VERSION 1.3
Page 12 of 13
12
3
Attach pair of brackets to top corners
of the back of the unit. Note there are
no existing pilot holes on the product.
Mark on wall where second pair
of brackets should be placed.
× 4
× 4× 4 × 4
× 2
CABINET Anti-Tip Installation
Drill holes in wall using
8mm / 5/16" drill bit.
Page 13 of 13
4A
4B
Align brackets on unit
with brackets on wall.
CABINET Anti-Tip Installation
Pull strap down until it snap-locks.
× 2 × 2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Article MYSEN 19903 Assembly Instructions

Brand
Article
Model
MYSEN 19903
Type
Assembly Instructions
This manual is also suitable for

Article MYSEN 19903 will help you reduce the risk of tip-over by attaching it to your wall. You will need a drill to install the brackets on the wall, which should take around 20 minutes. The box includes 4 brackets, 4 M4x17mm screws, 4 M8x51mm plugs, 4 M6x70mm screws, and 2 straps. Use the 8mm or 5/16" drill bit to drill holes in the wall, and then align the brackets on the unit with the brackets on the wall. Once you pull down the strap, it will snap and lock into place.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents