Panasonic CQVW100N Operating instructions

Brand: Panasonic

Model: CQVW100N

Category: Car speakers

Type: Operating instructions

BATTERY 15A

ACC

SIDE BRAKE

Wiring/Verdrahtung/Câblage/Bedrading/Cablaggio/Conexiones eléctricas

Fuse (15 A) Refer fuse replacement to your nearest authorized

Panasonic Service Centre. Do not try fuse replacement by yourself.

Sicherung (15 A) Wenden Sie sich zum Austausch der Sicherung

an eine autorisierte Panasonic-Kundendienststelle in Ihrer Nähe.

Versuchen Sie nicht, den Austausch selbst vorzunehmen.

Fusible (15 A) Confiez le remplacement de fusible au centre de

service après-vente Panasonic agréé le plus proche. N’essayez pas

de remplacer le fusible tout(e) seul(e).

Zekering (15 A) Laat het vervangen van de zekering over aan uw

dichtstbijzijnde Panasonic service-centrum. Probeer in geen geval

zelf de zekering te vervangen.

Fusibile (15 A) Per la sostituzione del fusibile rivolgersi al più

vicino Centro di Assistenza Panasonic autorizzato. Non tentare di

sostituire il fusibile da sé.

Fusible (15 A) Solicite el reemplazo del fusible al centro de

servicio Panasonic autorizado que le quede más cerca. No trate de

reemplazar usted mismo el fusible.

System-up Connector/System-Upgrade-Stecker/Connecteur de mise à niveau de système/Systeemuitbreidingsaansluiting/

Connettore di potenziamento del sistema/Conector de mejora del sistema

Antenna/Antenne/Antenne/Antenne/Antenna/Antena

Altavoces

B8 : Trasero Izquierdo –

(Verde con franja negra)

B7 : Trasero Izquierdo + (Verde)

B6 : Frontal Izquierdo –

(Blanco con franja negra)

B5 : Frontal Izquierdo + (Blanco)

B4 : Frontal Derecho –

(Gris con franja negra)

B3 : Frontal Derecho + (Gris)

B2 : Trasero Derecho –

(Violeta con franja negra)

B1 : Trasero Derecho + (Violeta)

Speakers

B8 : Rear Left –

(Green/black stripe)

B7 : Rear Left + (Green)

B6 : Front Left –

(White/black stripe)

B5 : Front Left + (White)

B4 : Front Right –

(Gray/black stripe)

B3 : Front Right + (Gray)

B2 : Rear Right –

(Violet/black stripe)

B1 : Rear Right + (Violet)

Lautsprecher

B8 : Hinten Links –

(Grün mit schwarzem Streifen)

B7 : Hinten Links + (Grün)

B6 : Vorne Links –

(Weiß mit schwarzem Streifen)

B5 : Vorne Links + (Weiß)

B4 : Vorne Rechts –

(Grau mit schwarzem Streifen)

B3 : Vorne Rechts + (Grau)

B2 : Hinten Rechts –

(Violett mit schwarzem Streifen)

B1 : Hinten Rechts + (Violett)

Haut-parleurs

B8 : Arrière Gauche –

(Vert à rayures noires)

B7 : Arrière Gauche + (Vert)

B6 : Avant Gauche –

(Blanc à rayures noires)

B5 : Avant Gauche + (Blanc)

B4 : Avant Droit –

(Gris à rayures noires)

B3 : Avant Droit + (Gris)

B2 : Arrière Droit –

(Violet à rayures noires)

B1 : Arrière Droit + (Violet)

luidsprekers

B8 : Achter Links –

(Groen met zwarte streep)

B7 : Achter Links + (Groen)

B6 : Voor Links –

(Wit met zwarte streep)

B5 : Voor Links + (Wit)

B4 : Voor Rechts –

(Grijs met zwarte streep)

B3 : Voor Rechts + (Grijs)

B2 : Achter Rechts –

(Paars met zwarte streep)

B1 : Achter Rechts + (Paars)

Altoparlanti

B8 : Posteriore Sinistro –

(Verde con riga nera)

B7 : Posteriore Sinistro + (Verde)

B6 : Anteriore Sinistro –

(Bianco con riga nera)

B5 : Anteriore Sinistro + (Bianco)

B4 : Anteriore Destro –

(Grigio con riga nera)

B3 : Anteriore Destro + (Grigio)

B2 : Posteriore Destro –

(Viola con riga nera)

B1 : Posteriore Destro + (Viola)

A4 : Battery Lead (Yellow)

A5 : Motor Antenna Relay Control Lead (Blue)

A7 : Power Lead (IGN or ACC) (Red)

A8 : Ground Lead (Black)

A4 : Batteriekabel (Gelb)

A5 : Steuerkabel für Relais der motorbetriebenen Antenne (Blau)

A7 : Versorgungskabel (IGN oder ACC) (Rot)

A8 : Massekabel (Schwarz)

A4 : Fil de batterie (Jaune)

A5 : Fil de commande de relais de moteur d’antenne (Bleu)

A7 : Fil d’alimentation (IGN ou ACC) (Rouge)

A8 : Fil de masse (Noir)

A4 : Accudraad (Geel)

A5 : Antennemotorrelais-stuurdraad (Blauw)

A7 : Stroomdraad (IGN of ACC) (Rood)

A8 : Massadraad (Zwart)

A4 : Cavo batteria (Giallo)

A5 : Cavo di controllo relé antenna motorizzata (Blu)

A7 : Cavo di alimentazione (IGN o ACC) (Rosso)

A8 : Cavo di massa (Nero)

A4 : Cable de la batería (Amarillo)

A5 : Cable de control del relé de la antena motorizada (Azul)

A7 : Cable de la alimentación (IGN o ACC) (Rojo)

A8 : Cable de masa (Negro)

1 Side Brake (Parking Brake) Connection Lead

2 External Remote Control Lead

3 External Amplifier Control Power Lead

4 Reverse Lead

1 Handremdraad

2 Externe afstandsbedieningsdraad

3 Externe versterker stroomstuurdraad

4 Achteruit-draad

1 Verbindungskabel für Feststellbremse (Handbremse)

2 Leitungsdraht für externe Fernbedienung

3 Stromsteuerkabel des externen Verstärkers

4 Rückwärtsgangkabel

Fil de connexion de frein à main (frein de stationnement)

2 Fil de la télécommande extérieure

3 Fil d’alimentation pour commande d’amplificateur

extérieur

4 Fil de marche arrière

1 Cavo di collegamento del freno a mano (freno di stazionamento)

2 Cavo di telecomando esterno

3 Cavo alimentazione controllo amplificatore esterno

Cavo di retromarcia

1 Cable de conexión del freno de mando (freno de estacionamiento)

2 Cable de control remoto externo

3 Cable de alimentación de control de amplificador externo

4 Cable de marcha atrás

(Bright green) (Leuchtend grün) (Vert clair)

(Lichtgroen) (Verde chiaro) (Verde claro)

(Brown/black stripe) (Braun mit schwarzem Streifen) (Brun à rayures noires)

(Bruin met zwarte streep) (Marrone con riga nera) (Marrón con franja negra)

(Blue/white stripe) (Blau mit weißem Streifen) (Bleu à rayures blanches)

(Blauw met witte streep) (Blu con riga bianca) (Azul con franja blanca)

(Violet/white stripe) (Violett mit weißem Streifen)

(Violet à rayures blanches) (Paars met witte streep)

(Viola con riga bianca) (Violeta con franja blanca)

¡Please read these instructions carefully before using this product and keep this manual for future reference.

¡Bitte lesen Sie diese Bedienungsanleitung vor der Verwendung dieses Produktes aufmerksam durch und bewahren Sie sie danach für spätere Nachschlagzwecke sorgfältig

auf.

¡Prière de lire ces instructions attentivement avant d’utiliser le produit et garder ce manuel pour l’utilisation ultérieure.

Leest u deze instructie alstublieft zorgvuldig door voor u dit product in gebruik neemt en bewaar deze handleiding voor later gebruik.

Si prega di leggere attentamente queste istruzioni prima di usare questo prodotto e di conservare questo manuale per usi futuri.

¡Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

Installation Instructions

Einbauanleitung

Instructions d’installation

Installatiehandleiding

Istruzioni per l’installazione

Instrucciones de instalación

TEXT

Model: CQ-VW100N

CQ-VW100N

English

Safety Information

CAUTION:

• PLEASE FOLLOW THE LAWS AND REGULATIONS

OF YOUR STATE, PROVINCE OR COUNTRY FOR

INSTALLATION OF THE UNIT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE

THIS APPLIANCE TO RAIN, SPLASHING, DRIP-

PING OR MOISTURE.

CQ-VW100N

English

Upgrade Options

Safety Information................................................2

Upgrade Options..................................................3

Installation ............................................................4

Electrical Connections ........................................9

Contents

Main Unit

CQ-VW100N

Expansion Module

(CY-EM100N, option)

CD Changer

(CX-DP880N, option)

DVD Changer

(CX-DH801N, option)

Rear Monitor

iPod

TV Tuner

(CY-TUP153N, option)

Hands Free Kit with Audio Streaming

featuring Bluetooth

technology

(Bluetooth unit: CY-BT200N, option)

CQ-VW100N

English

Installation

Preparation Dashboard Installation

¡Before installation, check the radio operation with

antenna and speakers.

¡Disconnect the cable from the negative (–) battery ter-

minal (see caution below).

¡The unit should be installed in a horizontal position

with the front end up at a convenient angle, but not

more than 30°.

Installation Opening

The unit can be installed in any dashboard having an

opening as shown below. The dashboard should be 4.5

mm – 6 mm thick in order to be able to support the unit.

Installation Precautions

This product should be installed by a professional

installer, if possible.

In case of difficulty, please consult your nearest author-

ized Panasonic Service Centre.

1. This system is to be used only in a 12 V DC battery

system (car) with negative ground.

2. Follow the electrical connections carefully (

a page 9-

17). Failure to do so may result in damage to the unit.

3. Connect the power lead after all other connections are

made.

4. Be sure to connect the battery lead (yellow) to the pos-

itive terminal (+) of the battery or fuse block (BAT) ter-

minal.

5. Insulate all exposed wires to prevent short circuiting.

6. Secure all loose wires after installing the unit.

7. Please carefully read the operating and installation

instructions of the respective equipment before con-

necting it to this unit.

0 – 30°

182 mm

111.6 mm

Caution

¡Do not disconnect the battery terminals of a car with

trip or navigational computer since all user settings

stored in memory will be lost. Instead take extra

care with installing the unit to prevent shorts.

Caution

¡Please follow the laws and regulations of your

province or country for installation of the unit.

¡When bending the mounting tab of the mounting

collar with a screwdriver, be careful not to injure

your hands and fingers.

¡We strongly recommend you to wear gloves for

installation work to protect yourself from injuries.

CQ-VW100N

English

Lock Cancel Plate

❏ Transportation Bracket Removal

Be sure to remove the transportation brackets before

use (installation).

Use round head screws (5 mmø x

8 mm) for installation.

(a page 7)

Be careful not to lose these screws.

Round Head Screw (5 mmø x 8 mm)

Transportation Bracket

❏ Installation Hardware

(For Installation)

Note:

¡The number in parenthesis underneath each accessory

part name is the part number for maintenance and

service.

¡Accessories and their parts numbers are subject to

modification without prior notice due to improvements.

¡Mounting Collar w is mounted on the main unit at

shipment.

¡Use the supplied screws for installation exclusively. In

case of losing any of them, please order the specific

screw.

Qty.DiagramItemNo.

Trim Plate

Mounting Collar

Round Head Screw

(5 mmø x 8 mm)

Flat-Head Screw

(5 mmø x 8 mm)

Mounting Bolt (5 mmø)

❏ Before Installation

Caution

¡Do not press the panel forcefully.

¡Do not scratch the panel with fingernails or any hard

objects.

¡Do not bump the front panel.

a Failure to observe the above may damage or

break the glass on the surface of the touch panel.

❏ Installation Hardware

(For

Wiring)

Qty.DiagramItemNo.

Power Connector

(ISO connector)

ISO Antenna Adapter

CQ-VW100N

English

Installation (continued)

❏ Mounting Procedures (A) (When using Mounting Collar w)

Mounting and removing the Main Unit

Note:

¡The car model, installation conditions and combination

of the units used may impose some restrictions on

opening and closing the monitor as well as on the

angle and position to which the monitor can be adjust-

ed.

IMPORTANT

When this unit is installed in dashboard, ensure that there

is sufficient air flow around the unit to prevent damage

from overheating. Do not block any ventilation holes on

the unit.

Insert the Mounting Collar w into the dash-

board, and bend the mounting tabs out with

a screwdriver.

Establish the rear connection of the unit.

After fixing Power Connector u, fix the rear

of the unit to the car body by either method

(a) or (b).

Insert the unit into Mounting Collar w.

Secure the clamp plate of Mounting Collar w

to the hook.

Insert Trim Plate q.

After installation reconnect the negative (–)

battery terminal.

Snapping point

(a) Using the Rear Support Strap (option) (b) Using the Rubber Cushion (option)

Fire wall of car

3 mmø

Tapping Screw

(5 mmø x 16 mm)

(option, XTT5+16AFN)

Rear Support Strap

(option, YEFG044C002)

Mounting Bolt

(5 mmø)

To the unit

Mounting Bolt

(5 mmø)

Rear Support Bracket

(Provided on the Car)

Rubber Bushing

(option)

Hex. Nut (5 mmø)

(option, YEJN99023)

Method for Fixing the Rear of the Unit

CQ-VW100N

English

❏ Mounting Procedures (B)

(When not using Mounting Collar w)

Use the brackets supplied with your car when mounting

this unit. The bracket shape and mounting method vary

with car manufacturers, car types and manufacturing

year. Please consult your nearest dealer or installer.

❏ Removing Procedures

q Remove the trim plate q.

w Lock release.

q Insert the lock cancel plate e until you hear a

click.

w Pull the unit out.

e Pull the unit out with both hands.

Note:

¡Use pliers to bend the fingers

on the bracket vertically.

Select mounting screws according to the hole

positions and hole shape of the bracket.

t Round Head Screw

(5 mmø x 8 mm)

Note:

¡Reuse the two round head screws removed

from the transportation brackets. (

a page 5)

y Flat-Head Screw

(5 mmø x 8 mm)

CQ-VW100N

English

Installation (continued)

Connecting the Side Brake (Parking Brake) Connection Lead

—

SIDE BRAKE

The side brake (parking brake) switch position varies with car model.

For details on the exact location of the side brake (parking brake) switch

in your car, contact your dealer.

q Attach a Clip Connector to the end of the side brake

(parking brake) connection lead.

w The Clip Connector is connected to the power

source side lead of the side brake (parking brake)

lever.

Hand brake Foot brake

Side Brake (Parking Brake) Connection

Lead

(Bright green)

When the side brake (parking brake) lever is

engaged, the unit is grounded by the chassis.

Side brake (parking brake) switch

Car chassis

Battery

Brake light

Clip Connector

(From car accessories stores)

Side Brake (Parking Brake) Connection Lead

(Bright green)

Comes up to this point.

Power source side lead

Caution

¡For safety, be sure to ask your nearest professional installer to do this connection.

CQ-VW100N

English

Electrical Connections

Precautions (ISO Connector)

¡The pin arrangement of the power connector conforms

to ISO standard.

¡The pin arrangement of ISO connectors in some cars

may differ from the ISO standard.

¡Please check that the pin arrangement of the connec-

tor in your car conforms to ISO standard.

¡For car types A and B, change the wiring of the red

and yellow leads as shown at below.

¡After connection, insulate the portions marked (✽)

with insulating tape.

Note:

¡For cars other than types A and B, please consult your

local car shop.

(✽)

BATTERY 15A

ACC

(✽)

BATTERY 15A

ACC

(✽)

ISO

Standard ISO

Car Type A

Car Type B

BATTERY 15A

ACC

A7: IGN or ACC 12 V supply

(Red)

(Yellow)

(Red)

(Yellow)

(Red)

(Yellow)

(Red)

(Yellow)

A4: IGN or ACC 12 V supply

A4: 12 V Batteries (Continuous supply)

A7: 12 V Batteries (Continuous supply)

A4: No connection

Note:

¡To prevent from damage to the unit, be sure to follow

the wiring diagrams at right.

¡Be sure to fully plug in the connectors. Secure them

with clamps and tapes.

¡All other installation methods require the use of dedi-

cated metal fittings. Consult with a qualified servicing

engineer or your dealer if other methods are required.

Caution

¡Check the connectors provided on your car (see precaution below) before connecting the system.

¡This unit is designed for use in a car having a 12 V negative ground battery system.

¡To prevent damage to the unit, be sure to follow the connection diagram.

¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords).

¡Do not insert the power connector into the unit until the wiring is completed.

¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and pre-

vent cable terminals from touching any metal parts.

¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery

may clear the memory.

¡Run the cords avoiding the spots where the temperature can be extremely high.

CQ-VW100N

English

Electrical Connections (continued)

❏ Wiring Diagram

VIDEO OUT

CAMERA IN

S.W OUT

PRE OUT REAR

EXT VIDEO IN

PRE OUT FRONT

Video Output Terminal (VIDEO OUT)

Connect the rear monitor. (a page 15)

Pre-Out Connector (front)

To an external amplifier.

Pre-Out Connector (rear)

To an external amplifier.

Video Input Terminal (EXT VIDEO IN)

Connect the video output terminal of Expansion Module

(CY-EM100N, option).

Audio/Video Input Terminal (AV1 IN)

Audio/Video Input Terminal (AV2 IN)

Connect a VCR, camcorder, other brand’s car

navigation system, etc. (

a page 15)

Camera Input Terminal (CAMERA IN)

Connect a rear view camera. (a page 16)

(Yellow)

(R)(Red)

(L)(White)

(R)(Red)

(L)(White)

(Yellow)

Pre-Out Subwoofer connector (mono)

To an external amplifier.

(Black)

(Yellow)

Fuse (15 A) Refer fuse replacement to your nearest

authorized Panasonic Service Centre. Do not try fuse

replacement by yourself.

CQ-VW100N (Rear)

(R)(Red)

(L)(White) (Yellow)

CQ-VW100N

English

Radio Antenna Connector (RADIO ANT IN)

System-up Connector

To external devices equipped with sys-

tem-up connector.

ISO Antenna Adapter

(If needed)

SIDE BRAKE

BATTERY 15A

ACC

A8 (Black)

A7 (Red)

A4 (Yellow)

A5 (Blue)

B8 (Green/black stripe)

B7 (Green)

B6 (White/black stripe)

B5 (White)

B4 (Gray/black stripe)

B3 (Gray)

B2 (Violet/black stripe)

B1 (Violet)

Not used.

A5 : Motor Antenna Relay Control

Lead

(Blue)

To Motor Antenna (Max. 100 mA).

This lead is not intended for use with a

switch actuated power antenna.

Note:

¡The power antenna extends auto-

matically when the power of this

unit is turned on.

A7 : Power Lead (IGN or ACC) (Red)

To ACC power, +12 V DC.

A8 : Ground Lead (Black)

To a clean, bare metallic part of the

car chassis.

A4 : Battery Lead (Yellow)

To the car battery, continuous +12 V

DC.

Caution

¡Use ungrounded speakers only.

Allowable input : 50 W or more

Impedance : 4 – 8 Ω

Use of speakers which do not match the specifica-

tions can cause burning, smoking or damage of

the speakers.

¡Distance between speaker and amplifier: 30 cm or

¡Do not connect more than one speaker to one set of

speaker leads. (except for connecting to a tweeter)

Side Brake (Parking Brake) Connection Lead

(Bright green)

Be sure to wire the side brake (parking brake) for safety

and preventing accidents.

External Remote Control Lead

(Brown/black stripe)

When using non-Panasonic external remote control, refer

to the manufacture for their product before connecting.

External Amplifier Control Power Lead

(Blue/white stripe)

To an external amplifier.

Note:

¡Use the power control lead of the TV tuner for TV

tuner connection.

¡Connect both the power control lead of the TV tuner

and the amplifier control connector of the external

amplifier when the TV tuner and external amplifier are

connected at the same time.

B8 : Rear Left –

B7 : Rear Left +

B6 : Front Left –

B5 : Front Left +

B4 : Front Right –

B3 : Front Right +

B2 : Rear Right –

B1 : Rear Right +

Speakers

Power Connector

To power connector of the unit.

Reverse Lead (Violet/white stripe)

When connecting the rear view camera, use the

reverse lead. (

a page 13)

CQ-VW100N

English

Electrical Connections (continued)

Connection with DVD Changer (CX-DH801N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

CHANGER IN

BATTERY 5 A

ACC

EXT VIDEO IN

CQ-VW100N

(Rear)

RCA Cord

(Video)

(Yellow)

(L) (White)

(R) (Red)

DIN Connector

DIN Cord

(Black)

DVD Changer

CX-DH801N (option)

Battery Lead

(Yellow) To the car battery, continuous +12 V DC

Power Lead (Red) (not used)

Ground Lead (Black)

To a clean, bare metallic part of the car chassis

Power Connector

(Supplied with CX-DH801N)

Conversion Cable for DVD/CD Changer

(CA-CC30N, option)

System-up

connector

Video Input Terminal

(EXT VIDEO IN)

CQ-VW100N

English

Connection with CD Changer (CX-DP880N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

CHANGER IN

(L) (White)

(R) (Red)

DIN Connector

Conversion Cable for DVD/CD

Changer

(CA-CC30N, option)

CQ-VW100N

(Rear)

System-up connector

DIN Cord

(Black)

CD Changer

CX-DP880N (option)

Power Connector

(Supplied with CX-DP880N)

RCA Cord

Battery Lead

(Yellow)

To the car battery, continuous

+12 V DC

Ground Lead (Black)

To a clean, bare metallic part of the car

chassis

CQ-VW100N

English

Electrical Connections (continued)

Connection with TV Tuner (CY-TUP153N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

PWR-CONT

EXT VIDEO IN

TV Tuner

CY-TUP153N (option)

CQ-VW100N

(Rear)

(Video)

(Yellow)

System-up Connector

(supplied with CY-TUP153N)

System-up Connector

Power Connector

Power Control

Lead

RCA Cord

(supplied with CY-TUP153N)

External Amplifier Control Power Lead

Note:

¡Connect both the power control lead of the TV

tuner and the amplifier control connector of the

external amplifier when the TV tuner and external

amplifier are connected at the same time.

Power Connector

(supplied with CY-TUP153N)

Clip connector

(From car acces-

sories stores)

Video Input

Terminal (EXT

VIDEO IN)

CQ-VW100N

English

Connection with Expansion Module (CY-EM100N)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

EXT VIDEO IN

CHANGER IN

VIDEO-CNT

CQ-VW100N

(Rear)

VIDEO OUT

AUDIO OUT

VIDEO OUT

DVD Changer

CX-DH801N (option)

Expansion Module

CY-EM100N (option)

Conversion Cable for

DVD/CD Changer

(CA-CC30N, option)

Direct Cable for iPod with Video

(CA-VDC300N, option)

(Video) (Yellow)

(Video)

(Yellow)

(Video)

(Yellow)

(L) (White)

RCA cord

(option)

(R) (Red)

(Video) (Yellow)

(L) (White)

(R)

(Red)

Head unit/Expansion Module

Connecting cable

(Supplied with CY-EM100N)

Camcorder

iPod

System-up

Connector

Video Input Terminal

(EXT VIDEO IN)

CQ-VW100N

English

Electrical Connections (continued)

Connection with Rear Monitor

Note:

¡Refer to the operating instructions for the connected devices, in addition.

¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

INTELLIGENT SYSTEM

BS G-CODE

POWER

Connection with VCR or Camcorder

CQ-VW100N

(Rear)

(R)

(Red)

(L)

(White)

(Video)

(Yellow)

VCR

Camcorder

(R) (Red)

(L) (White)

(Video) (Yellow)

RCA Cord

(option)

Video Output

Audio Right

Audio Left

Note:

¡Refer to the operating instructions for the connected devices, in addition.

¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in

order to establish a proper connection.

Example:

VIDEO OUT

COLOR LCD MONITOR

VM1500

Panasonic

STAND BY (R)

ON (G)

CQ-VW100N

(Rear)

RCA Cord (option)

(Video) (Yellow)

Example:

Rear Monitor

Video Input

Audio Right

Audio Left

Caution

¡For people sitting in the front seats, please

enjoy only audio during driving.

Video Output Terminal (VIDEO OUT)

CQ-VW100N

English

Connection with Rear View Camera

Note:

¡Refer to the operating instructions for the connected devices, in addition.

CAMERA IN

Connecting the Reverse Lead

If using an optional rear view camera, the reverse lead must

be connected.

Connect the reverse lead (violet/white stripe) to the positive (+)

lead of the reverse lamp (the lamp with a clear lens that lights

when the transmission gear is shifted into the reverse position).

Note:

¡Connect the reverse lead after cutting the terminal at the end.

¡Use a Reverse Extension Cord (option) if needed.

Rear View Camera

(CY-RC50KN)

(option)

(Video)

(Yellow)

RCA Cord (option)

Rear View Camera

Control Unit

(option)

CQ-VW100N (Rear)

u Power Connector

Reverse lamp

Clip connector

(From car accessories

stores)

Battery

Car chassis

Transmission gear

Reverse Lead

(Violet/white stripe)

Camera Input

Camera Input Terminal (CAMERA IN)

(Yellow)

Check the reverse lamp.

Take it out of the back of

the tail lamp mount.

YFM294C124CA PTW1207-1018 Printed in China

Matsushita Electric Industrial Co., Ltd.

Web Site : http://panasonic.net

Installation Instructions

Panasonic CQVW100N Operating instructions

Brand: Panasonic

Model: CQVW100N

Category: Car speakers

Type: Operating instructions

Download PDF

report

Panasonic CQVW100N Operating instructions

Panasonic CQVW100N Operating instructions

Related papers

Other documents