Tommee Tippee 1094S Digital Video Monitor Owner's manual

Category
Baby video monitors
Type
Owner's manual

This manual is also suitable for

baby unit (=BU) 1094SB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Power On/O
Nightlight control
No movement sensor alarm
Movement sensor light ashes green
with each movement baby makes
Camera
Infrared for night vision
Microphone
Low battery indicator
Volume control 9a) Up 9b) Down
Sensor pad input socket
Camera tripod mount
Mains adaptor input socket
Sensor pad switch on/o
Battery compartment
Temperature detector
Sensor pad sensitivity switch
Press to power on or o.
LED lights up amber when switched on.
Low. medium, high.
ON - when alarm is triggered.
FLASHES - if alarmed but child then starts
to move again.
OFF
FLASHES ORANGE when battery is low
if using batteries. CONSTANT ORANGE
when using AC power adapter.
Takes 4 x AA alkaline batteries (not included).
Remove casing using a screwdriver.
Low, medium and high.
17
19
18
14
16
13
15
1210
position
for leads
11
1
5
2
4
3
6
8
7
9a
9b
movement sensor pad
17
18
19
Sensor pad
Connection lead plugs into baby unit
Connecting plug
digital video monitor
with movement sensor pad
INSTRUCTIONS FOR USE
model 1094S
tommeetippee.com
parent unit (=PU) 1094SP
3
2
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mains power on/o
Zoom
Power indicator
Talkback
Menu
Volume Up
Volume Down
Left/back
Right
Mains adaptor /
recharging input socket
Link Indicator
Mute Indicator
LCD on/o
Antenna
Microphone
Sensor Pad Alarm
In monitoring mode: Press to power on or o the unit.
In monitoring mode: Press to zoom in. Press again to zoom out
GREEN = charging
In monitoring mode: Press and hold to talk back with baby
unit. Release to quit the talk mode
In monitoring mode: Press to access the main menu.
In menu mode: Press to conrm function selected.
In monitoring mode: Press to increase the speaker volume.
In menu mode: Press to scroll the menu options.
In zoom mode : Press to navigate the zoom panel up.
In monitoring mode: Press to decrease the speaker volume.
In menu mode: Press to scroll the menu options.
In zoom mode: Press to navigate the zoom panel down.
In menu mode: Press to view the previous menu level. Press
and hold to move back to the monitoring mode directly.
In zoom mode: Press to navigate the zoom panel left.
In zoom mode: Press to navigate the zoom panel right.
STEADY ORANGE = link between parent unit and baby unit is
excellent.
SLOW FLASHING ORANGE = link between parent unit and
baby unit is good.
QUICK FLASHING ORANGE = link is out of range. ‘NO LINK’ is
displayed.
OFF = parent unit is not powered on.
ON = Blue when parent unit speaker is muted
OFF in all other cases
In monitoring mode : Press to turn ON or OFF.
In menu mode : Press to go to the monitoring mode.
Position upright when in use.
FLASHING GREEN - movement is detected
RED - NO movement is detected at least in the last 20 seconds
FLASHING RED - If alarmed and child then starts to move
again.
800
10
M
6
9
7
2 1 15 8 5
13 4
3
12
11
16
14
Language
Display
Tick Tone
Alert Tone
Sensitivity
Vibration
Nightlight
parent unit icons status icons
ICON
DESCRIPTION
Antenna
Zoom
Speaker o/Mute
Sensor Pad Connect
No Movement alarm
Volume control
Battery
Power plug
Nightlight
Up arrow of scroll bar
Down arrow of scroll bar
ICON
DESCRIPTION
5
4
parent unit LEDs
charging your monitor before rst use:
THE PARENT UNIT:
The parent unit is supplied with a rechargeable battery pack.
To insert the battery pack, open the battery casing with a screwdriver. Insert the supplied
rechargeable battery pack. Take extra care to ensure that the battery pack is inserted correctly and
the right way round. Ret the battery casing securely with a screwdriver.
DO NOT use a non-rechargeable battery pack. ONLY use battery pack supplied.
Plug the mains power cable into socket on side of parent unit and connect the other end of the
mains power cable to the mains power.
Power on the parent unit and charge for 10 hours before use.
THE BABY UNIT:
The baby unit does not require batteries if powered from the mains.
If mains usage is not available, the baby unit will operate on batteries 4 x alkaline AA (LR6), which are
not supplied.
To insert batteries, open the battery casing with a screwdriver. Insert 4 x alkaline AA (LR6) batteries
(rechargeable or non-rechargeable, but not mixed) and close casing securely with screwdriver. Take
extra care to ensure that the batteries are inserted correctly and the right way round.
There is NO charging function on the baby unit.
The battery light ashes orange to indicate the battery is low.
Battery power is disconnected automatically when the mains adaptor is in use. If the adaptor is turned o
at the mains and still remains connected to the monitor then the batteries will be automatically activated.
1
1
2
3
4
5
2
3
4
5
6
M
3
20°C
3
20°C
correct use of batteries
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are to be removed from the baby unit before being charged.
Rechargeable batteries are only to be charged under adult supervision.
Dierent types of batteries or new and used batteries are not to be mixed.
Only batteries of the same or equivalent type as recommended are to be used.
Batteries are to be inserted with the correct polarity.
Exhausted batteries are to be removed from the monitor.
CAUTION: risk of severe malfunction if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
SIGNAL STRENGTH
BATTERY
ZOOM
SENSOR PAD
NO MOVEMENT
ALARM
SPEAKER
TEMPERATURE
FLASH
ON
ON
FLASH
ON
OFF
ON
FLASH
OFF
ON
Signal obtained, but no connection
Signal weak
Signal good
Signal excellent
Signal out of range
Empty and needs to be recharged
Low
Full
Charging
Display when the Sensor Pad is
connected securely and turned ON
Flashes when Sensor Pad is ON but not
securely connected/disconnected
Show as constant when Sensor Pad is
connected but switched o at Baby Unit
OFF when Sensor Pad function is OFF
and not connected
Display when the ALARM is triggered
Flashes if alarmed but then the child
starts to move again
Indicates volume level when user
adjusts volume
Degree
Celsius
Fahrenheit
PAD OFF
°
C
F
MAINS POWER
NIGHT LIGHT
ON
On when parent unit is connected with
AC power adaptor and without battery
pack installed
Low
Medium
High
3
2
1
CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according
to the instructions. Use only rechargeable Li-polymer battery 950mAh with rating: 3.7/950mAh.
Rechargeable battery: Manufacturer: BYD COMPANY LIMITED Model no.: SCD530-1
FOR REPLACEMENT PARENT UNIT BATTERIES, VISIT OUR WEBSITE www.tommeetippee.com
Check immediately the location of corded monitors to make sure cords are out of arms reach of
your baby and other young children.
Place cords more than a metre away from any part of the cot. The monitor must not be used in any
other sleep environment.
Check the location of the monitor periodically, as what is within arms reach to a baby will change as
the baby grows.
Make sure the sensor cords are taut and not dangling to reduce the strangulation hazard.
Do not place furniture or other obstructions on the adaptor cords and be sure to position them so
that nobody can trip over them
Keep adaptor cords away from hot surfaces such as radiators and central heating pipes.
Be careful not to position the adaptor where a child might try to stop on it.
Never use Tommee Tippee monitor adaptors with any other equipment. Nor should you use any
other adaptors with your Tommee Tippee monitor.
Please note that the adaptors become warm in use –
this is quite normal and not a hazard.
The adaptors convert your AC power to a safe low DC voltage.
Use the power adaptor provided.
The product is only suitable for use for cots and cotbeds that comply with EN716.
Adaptor:
Manufacturer: TEN PAO INTERNATIONAL LTD.
Model no.: EU: S006MV0600080 UK: S006MB0600080
setting up the parent unit
Connect the mains adaptor into a nearby wall socket in your baby’s nursery and switch on the power
at the mains.
Press POWER on the parent unit until the POWER INDICATOR is on. The parent unit is now powered
on and the parent unit will search for and link itself to the baby unit.
Ensure that the sensor pad on-o switch is turned OFF.
In monitoring mode, you can press <LCD ON/OFF> on the parent unit. Turning o the LCD will not
power o the parent unit, you can still monitor the baby with it
setting up your baby unit
Connect the mains adaptor into a nearby wall socket in your baby’s nursery and switch on the power at
the mains.
Press POWER on the baby unit until the POWER INDICATOR is on. The baby unit is now powered on and
will link with the parent unit.
Ensure that the sensor pad on-o switch is turned OFF.
Direct the camera towards the babys cot. For adjusting the zoom feature, refer to section
Adjusting the Zoom.
testing the parent unit
First ensure that the baby unit has been set up and is working correctly following the previous
instructions.
To test the parent unit you must ensure that it is at least 5 metres away from the baby unit.
Turn the sensor pad OFF.
Place a sound source in the nursery at least 1 to 1.5 metres away from the baby unit, close the nursery
door and go to another room with the parent unit only.
Turn on the power and adjust the volume up or down to a comfortable level.
You will hear sounds from your nursery.
Walk around your house and garden with the parent unit, ensuring that you can hear the sounds from
the baby unit at all times. The monitor will work up to a distance range of 300m approximately.
Depending on the surrounding conditions as well as spatial and structural factors. The range indoors is
normally less than outdoors.
If you lose the signal from the baby unit a beep tone will be emitted from the parent unit and the
antenna icon will ash. Even if the speaker volume is set OFF, the alert tone will still emit at volume
level 1 when no link alert is triggered. Alert tone will only be emitted once initially. The screen will
continue to show NO LINK until restored.
1
2
3
4
1
2
3
4
NOTE:
Any triggering events such as baby cries, temperature of baby’s room exceeds the alert range,
parent unit loses link with baby unit, etc. will turn on the LCD automatically.
WARNING about using the baby unit!
The baby unit should be 1 to 1.5 metres away from the baby’s cot on a at surface or use the
tripod mount.
Never place the baby unit in or attach to the baby’s cot.
9
8
WARNING about the danger of cords:
STRANGULATION HAZARD! - Keep cords out of the reach of children.
Do not use with an extension cord.
WARNING! STRANGULATION HAZARD! Children have STRANGLED in cords.
When using without protective covering. Keep this cord out of the reach of children
(more than 0.9 m (3ft) away).
!
adjusting the tick tone:
The audible ticking sound gives reassurance that your sensor pad is correctly connected and the monitor is
sensing movement. If you wish to switch o the ticking sound:
Press <MENU> to access main menu
Press
UP or DOWN to select tick tone.
Press <MENU> to enter the sub-menu.
Press
UP or DOWN> to select from ON to OFF.
Press <MENU> to conrm.
adjusting the sensitivity of the sensor pad:
This monitor is compatible with standard cot mattresses. With thicker mattresses (ie spring interior) you may
need to adjust the sensitivity switch on the baby unit from it’s preset medium level to the high level. With
some very thin mattresses you may need to change a low sensitivity level.
setting up the movement sensor pad
The monitor has the ability to monitor your babys movements via the highly sophisticated movement
sensor pad. It is designed for use in a cot with a at, rm base. It should not be used in a travel cot, swinging
crib, moses basket, or with a hollow or foam-free mattress.
Place the sensor pad between the cot mattress and the cot base, directly under the area where your baby
will be sleeping.
Ensure the sensor pad is positioned the correct way up and that the connecting cord is fed through the
base of the cot out of accessibility range of your baby (50cm from the surface of mattress) and other
young children.
If the cot has a solid base it may be necessary to make a small hole through which the connecting
cord can pass.
Ensure the connecting cord plug is pushed fully into the socket underneath the baby unit.
Do not hang cable over the top or through the bars of the cot.
Place the cable down and onto the oor.
3
4
5
if the movement sensor alarm sounds:
The tommee tippee closer to nature movement sensor pad is NOT a medical device and is NOT
designed to prevent cases of Sudden Infant Death Syndrome (SIDS). This tommee tippee closer to
nature monitor is intended to help you monitor your child and is NOT to be used as a substitute for
adult supervision.
The alarm going o may not be a sign of a problem with your baby. It may be a sign that the baby has
moved away from the sensor pad area, or that batteries are running low if not mains power operated.
IMPORTANT !
TEST YOUR SENSOR PAD BEFORE PROCEEDING FURTHER:
1 Turn the Sensor Pad switch to ON. The Sensor Pad LED on the Baby Unit will light up if movement is
detected.
2 The Sensor Pad LED will light up GREEN and ash to show the connection is good and continuous
movement is detected from child.
3 Check the sensor pad is working by touching the cot mattress gently anywhere near where your baby
will be sleeping.
4 If the Parent Unit is linked with the Baby Unit successfully, the Sensor Pad icon will appear on the Parent
Unit. The Sensor Pad status LED will light up if movement is detected and there will be an audible tick
sound . The volume of the tick can be adjusted.
5 If the Sensor Pad switch is ON without the Sensor Pad being connected securely, there will be an error
tone from the Baby Unit and the Sensor Pad icon in the Parent Unit will ash. The text ‘PLEASE
CONNECT THE SENSOR PAD’ will also appear on the Parent Unit.
6 Test the alarm by continuing to touch the mattress for a few moments and then step away from the cot
and stop all movement near the sensor pad.
7 After approximately 20 seconds the alarm will sound on both the Parent Unit and Baby Unit and the RED
alarm light will come on . The text ‘PLEASE CHECK THE BABY’ will also appear on the parent unit until
the Sensor Pad is reset.
8 If movement is detected again after the alarm has activated the alarm will stop and the red alarm light
will ash on the baby unit and the parent unit to let you know that the alarm has activated.
9 To reset the alarm, switch the Sensor Pad o and on again.
10 If the Sensor Pad is securely installed, but switched o on the Baby Unit the text ‘PLEASE TURN ON THE
SENSOR PAD will be displayed on the Parent Unit standby screen.
No alarm after 20 seconds
of NO movement
False alarm when there IS
movement
Make sure there is no movement or vibration around the
sensor pad and test again. If no alarm again after 20 seconds,
increase sensitivity setting and test again.
Check the connections are secure and test again. If alarm
triggers again, decrease sensitivity setting and test again.
WARNINGS ABOUT USING THE SENSOR PAD!
A moving or swinging cord may be interpreted by the sensor pad as a baby’s movement. To avoid this,
ensure that the cord is not positioned where it may be subject to movement.
You should ensure there is no vibration in or near the nursery, so that the sensor pad is monitoring only
your baby’s movements.
The sensor pad does not carry any electricity and will not aect your baby even if the mattress is subject
to bedwetting or vomiting.
Never immerse the sensor pad in liquid. To clean, wipe with a dry, lint free cloth.
Never place the connecting cord in contact with any moving objects, or near any heated surface.
Always ensure wires and cables are out of reach from your baby and younger children. Never place
connecting cords amongst your baby’s bedding, the child could be strangled.
Ensure the sensor pad is used the correct way up.
Do not immerse sensor mat in liquid and avoid contact with moisture.
HELPFUL ADVICE ABOUT USING THE SENSOR PAD:
If you remove your baby from the cot (e.g. for a feed) remember to turn o the sensor pad. to prevent the
alarm from sounding. Remember to switch the alarm back on when you put the baby back into the cot.
M
VOLUME 5
VOLUME 4
VOLUME 3
VOLUME 2
VOLUME 1
VOLUME OFF
VOLUME +
VOLUME -
adjusting speaker volume of parent unit and baby unit
There are 5 volume levels on baby unit from level 1 to level 5, and 6 volume levels on parent unit, including
level 1 to level 5 and Volume O. The volume level of parent unit will be shown on the status bar when you
adjust the volume.
ADJUSTING VOLUME OF PARENT UNIT
Press
UP to increase or DOWN to decrease the volume of the parent unit.
Mute icon will be displayed if the volume is turned o on the parent unit.
1
2
adjusting volume of baby unit
Press UP to increase or DOWN to decrease the volume of the baby unit.
An audible alert will emit when you reach the highest or lowest volume level.
Changing the volume setting on the baby unit aects the volume when you use the Talk Back feature.
1
2
1
2
3
4
5
6
1
2
3
helpful advice about using the nightlight
You may nd it useful to use a lower brightness if you wish your baby not to sleep in complete darkness
and then adjust to a higher brightness for when baby needs attention during the night and you do not
wish to turn on the main bedroom lights.
If operating in battery mode the brightness will function on Low (L) only and will fade out after 5 minutes.
parent unit settings of menu options
Language
Display
Tick tone
English
Brightness
On / O
Scroll 1 to 5 to adjust
LEVEL 1
parent unit menu options - continued
setting the language
Press <MENU> to access main menu.
Press
UP or DOWN to select LANGUAGE.
Press <MENU> to enter the sub-menu.
Press UP or DOWN to select the desired language.
Press <MENU> to conrm.
setting the display
Press <MENU> to access main menu.
Press
UP or DOWN to select DISPLAY.
Press <MENU> to enter the sub-menu to set the brightness level.
Press UP or DOWN to select from Level 1 to Level 5. You can preview the
brightness when scrolling the menu list.
Press <MENU> to conrm.
Sensitivity
Vibration
Nightlight
Temperature
Level 1
Level 2
Level 3
Level 4
Level 5 (most sensitive)
On / O
O / Low / Medium / High
Format
Minimum
Maximum
Alert
Levels 1 to 2, the microphone will
be voice activated by the noise
baby makes
Level 5, the microphone is always on
Fahrenheit or Celsius
52°F - 69°F or 11°C - 20°C
70°F - 86°F or 21°C - 30°C
LEVEL 1
1
2
3
4
5
1
2
3
4
5
LEVEL 2 LEVEL 3
LEVEL 2 LEVEL 3
adjusting the zoom
The zoom mode allows you to view your baby.
The ZOOM icon will be displayed in the status bar of the parent unit.
In monitoring mode, press <ZOOM> to enter zoom mode.
Press
UP/ DOWN / LEFT / RIGHT to navigate the zoom area.
Press <ZOOM> again to zoom out and return to the normal monitoring mode.
using the nightlight
Press the nightlight key on the baby unit.
To adjust the brightness or turn it o, press the key again with the sequence L>M>H>O
To turn on from the Parent Unit, select the nightlight main menu and select the brightness level.
The nightlight function is limited to level 1 if the Baby Unit is running on batteries.
The nightlight on the Baby Unit operates even if the Parent Unit is out of battery or turned o.
The nightlight settings and icons are synchronized when the Baby Unit and Parent Unit are connected.
using talkback
Talkback allows you to communicate from the parent unit to the baby unit to comfort and reassure your baby.
In monitoring mode, press and hold <TALK> on the parent unit to speak to baby.
The audio from the baby unit will be muted and the parent will not be able to hear the baby until the
button has been released. The mute icon will be displayed on parent unit status bar.
ADJUSTING THE TALKBACK VOLUME
The baby unit has 5 volume levels from Level 1 to Level 5
During TalkBack, press
UP or DOWN on the baby unit to increase or decrease the volume respectively.
NOTE:
The LCD backlight is always on when in AC power mode from the mains. If operating in battery
mode, the LCD backlight will fade out after 20 seconds after last key press.
1
2
3
4
5
6
1
2
3
4
5
7
6
1
2
3
4
5
6
7
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
adjusting the sound sensitivity
You can change the level of sensitivity on your baby monitor to suit your baby. For example, if your baby is a
particularly quiet sleeper, you can increase the sensitivity levels so that you are sure to hear if baby disturbs
or becomes uncomfortable.
There are 5 dierent levels. The microphone will be voice activated by the noise baby makes. Level 5 is the
most sensitive. The sound sensitivity settings of the baby unit can be changed only when parent unit is
linked with the baby unit:
Press <MENU> to access main menu
Press UP or DOWN to select SENSITIVITY.
Press <MENU> to enter the sub-menu.
Press
UP or DOWN to select from Level 1 to Level 5.
Press <MENU> to conrm.
setting the temperature format
The Baby Unit constantly monitors the temperature in your baby’s room and alerts you if it gets too hot or too
cold. The temperature is displayed
Press <MENU> to access main menu
Press
UP or DOWN to select TEMPERATURE.
Press <MENU> to select Format.
Press <MENU> to enter the sub-menu.
Press
UP or DOWN to select Celsius or Fahrenheit.
Press <MENU> to conrm.
The real-time temperature format displayed on the status bar of parent unit will be changed accordingly.
setting the vibration
Press <MENU> to access main menu
Press
UP or DOWN to select VIBRATION.
Press <MENU> to enter the sub-menu.
Press
UP or DOWN to turn the vibration ON or OFF.
Press <MENU> to conrm.
If ON, the Parent Unit will vibrate once to conrm it is activated.
paging to locate the parent unit
If both UP (9a) and DOWN (9b) keys are pressed for 3 seconds on the baby unit at the same time,
the paging tone is emitted.
PAGING will be displayed on the LCD of the parent unit.
If volume is OFF before paging starts, reset it to default volume level (4).
During paging, any key pressed on the parent unit will stop the paging tone.
If the link is lost between the parent unit and the baby unit, the paging tone will not be emitted when
both
UP (9a) and DOWN (9b) keys are pressed together. There will be no change on baby unit.
If paging is not stopped, it will expire in 2 minutes.
Paging function does not work if parent unit is turned o.
resetting to default settings
parent unit default
Ensure the parent unit is powered OFF.
Press and hold
UP.
Press POWER.
The parent unit LCD will display ‘please press M to restore default settings.
Press M to conrm.
NOTE:
If LCD is o, and baby voice reaches the sensitivity level 3,4 or 5, the LCD will be turned on
automatically.
When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds
and therefore transmits more often. As a result, the units will consume more power.
NOTE:
The temperature displayed is for reference only. There may be a slight tolerance of the degree
accuracy comparing with the actual temperature. It is important to physically check the actual
temperature in your baby’s room regularly.
NOTE:
In vibration mode, the parent unit will vibrate when the noise level from the baby reaches
sensitivity level 3, 4 or 5 while the loudspeaker volume of the parent unit is switched o.
If the Parent Unit speaker volume is turned o whilst in monitoring mode and vibration mode,
the Parent Unit will vibrate once.
When the noise level from the baby reaches sensitivity level 3, 4 or 5, the vibrating alert is
triggered and will vibrate every 5 seconds.
baby unit default
Ensure the parent unit is powered OFF.
Press and hold
UP.
Press POWER ON, whilst still holding
UP.
After 3 seconds, the sensor pad alarm LED will ash.
Release
UP key and press DOWN key. The sensor pad LED will resume on.
TROUBLESHOOTING
The link light on the parent unit does not come on
Check whether the parent unit is powered on.
Check whether the supplied rechargeable battery pack is correctly installed and not drained.
The link light on the parent unit ashes
The parent unit and the baby unit may be out of range with each other. Reduce the distance between the
units, but not closer than 1.5 metres.
The baby unit may be switched o. Press <POWER> key to switch on the baby unit.
The low battery indicator on the baby unit ashes
Replace with 4 x alkaline AA (LR6) batteries or connect the baby unit to the mains power.
The low battery icon on the parent unit LCD screen ashes
The rechargeable battery pack in the parent unit is running low. Connect the parent unit to the mains
power with the supplied power adaptor for recharging.
The parent unit beeps
This means the connection has been lost with the baby unit. Reduce the distance between the parent
unit and the baby unit, but not closer than 1.5 metres.
The baby unit may be switched o. Switch on the baby unit.
The rechargeable battery pack in the parent unit is running low. Connect the parent unit to the mains
power with the supplied power adaptor for recharging.
The temperature alert may have triggered. Check the temperature of the baby’s room.
Cannot view the video image of baby from the parent unit.
The LCD may be turned o. Switch on the LCD.
The parent unit and the baby unit may be out of range with each other. Reduce the distance between the
units, but not closer than 1.5 metres.
The rechargeable battery pack in the parent unit is drained. Connect the parent unit to the mains power
with the supplied power adaptor for recharging.
Cannot hear sound or baby cry from the parent unit.
The volume level in the parent unit may be set too low. Increase the volume level of the parent unit.
The microphone sensitivity level of the baby unit may be set too low. Increase the sensitivity level of the
baby unit.
The parent unit and the baby unit may be out of range with each other. Reduce the distance between the
units, but not closer than 1.5 metres.
The parent unit is too sensitive to room sounds.
The microphone sensitivity level of the baby unit may be set too high. Decrease the microphone
sensitivity level of the baby unit from the parent unit.
The baby monitor system produces a high-pitched noise.
The parent unit and the baby unit are too close to each other. Make sure the parent unit and baby unit are
at least 1.5 meters away from each other.
The speaker volume of the parent unit maybe set too high. Decrease the volume of the parent unit.
How long does the nightlight last?
If the baby unit is run on batteries the nightlight will fade out after 5 minutes. If is run from the mains
electricity it will remain on until switched o.
Alkaline batteries in the baby unit are running low quickly.
The microphone sensitivity level of the baby unit may be set too high. Decrease the microphone
sensitivity level of the baby unit from the parent unit.
The volume level of the baby unit may be set too high which consumes power. Decrease the volume level
of the baby unit.
The rechargeable battery pack in the parent unit is running low quickly.
The volume level of the parent unit may be set too high. Decrease the volume level of the parent unit.
For a replacement battery, visit our website www.tommeetippee.com
Talkback feature is not working.
Make sure the baby unit is powered on and the link between parent and baby unit is normal.
GENERAL SAFETY INFORMATION:
Warning! Adult use only – Keep out of reach of children at all times. Do not allow a child to
play with it – It is not a Toy
Make sure you store your monitor in a safe place when not in use, away from heat and water.
Take care not to drop either unit as this may aect the functioning of you monitor.
IMPORTANT:
The Tommee Tippee monitor has been designed to give you added reassurance for those times when
you cannot be in the same room as your baby, it is NOT a substitute for proper adult supervision. It is
important that an adult stays within range of the monitor at all times during use. Please remember that
your Tommee Tippee monitor is not a medical device, nor a device to prevent cases of Sudden Infant
Death Syndrome or cot death’, and you should not rely on it for your baby’s well-being. You should
personally check your baby as frequently as necessary.
IMPORTANT SAFETY INSTRUCTIONS:
When using your equipment, basic safety precautions should always be followed to reduce the
risk of re, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or
laundry tub, in a wet basement or near a swimming pool.
2.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries
in a re, they may explode. Check with local regulations for possible special disposal instructions.
technical specications
No. of channels:
Frequency:
Power supply of Baby Unit:
Power supply of Parent Unit:
Transmitting power:
Operating temperature:
Range
Refresh rate
Display
50
2402-2478.5
Switching mode power supply, 6V/800mA or 4 x AA
alkaline batteries
Switching mode power supply, 6V/800mA or 950mA
Li-Polymer batteries
100mW
10°C to 39°C
Indoor => 50m, Outdoor 300m approx. depending on the
surrounding conditions as well as spatial and structural
factors.
Up to 25 fps, Dynamic Frame Rate
Color LCD (QVGA 320x240 pixel)
Use only with class 2 power source
DECLARATION OF CONFORMITY
We, Jackel International Ltd trading as Mayborn Baby and Child
Dudley Lane, Cramlington, Northumberland, NE23 7RH, UK
declare under our responsibility that the electrical product:
Tommee Tippee Model 1094S
Closer to Nature Digital Video Baby Monitor
Closer to Nature Digital Video Baby Monitor with Movement Sensor Pad
which this declaration relates to is in conformity with the following standards:
RF: EN 300 328
RF: EN 50371
EMC: EN 301489-1/-17
LVD: EN 60950-1
LED: EN 60825
Following the provisions of 1999/5/EC (R&TTE Directive) the product is produced by a manufacturing
organisation accredited to ISO 9001
Andrew Richardson - Quality Assurance Manager
Cramlington, December 2011
If you are having any problems in setting up your monitor or require any further information
please visit our website www.tommeetippee.com
Please retain our address for future reference:
Mayborn Baby and Child
Northumberland Business Park West
Cramlington
Northumberland
NE23 7RH, UK
441010
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Tommee Tippee 1094S Digital Video Monitor Owner's manual

Category
Baby video monitors
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI