Safety Warnings
For your continued safety and to reduce the risk of injury or electric shock, please
follow all the safety precautions listed below. Read all instructions carefully before
using the unit and keep them for future reference.
• Retain the manual. If you pass the unit onto a third party, make sure to include this
manual.
• This appliance is intended for indoor household use and similar applications such
as:
– farm houses and by clients in hotels, motels and other residential type
environments;
– bed and breakfast type environments;
– catering and similar non-retail applications.
• Make sure your home voltage matches the voltage displayed on the appliance. If
you are not sure, contact an electrician.
• Do not kink or wrap the mains cable and plug around the appliance, as this
may cause the insulation to weaken and split, particularly where it enters the
appliance.
• Ensure the mains cable is fully extended before use and arrange it so that it is not
in contact with any part of the appliance.
• Do not pull on the mains cable. Never move, carry or hang the appliance by the
mains cable.
• Always position the appliance with the mains plug in an accessible position and
avoid the use of an extension cable as it may overheat and create a potential re
risk.
• The appliance must have a minimum 50 cm clearance around all sides of the
appliance.
• Ensure that the unit is used on a stable and level surface. If the oor surface is
uneven there is a risk that the appliance could tip over. Also, excessive vibration
and noise may occur. If the appliance should be accidentally tipped over, please
immediately disconnect from the power supply.
• Do not use the appliance in wardrobes or near fabrics or clothing. Do not stand the
appliance on deep pile carpets.
• Do not use the appliance in areas where petrol, paints or other ammable
substances are used or stored.
• Do not use in very dusty areas as dust may accumulate on the heating elements
and cause overheating.
• Do not use if there are any visible signs of damage to the appliance.
• Do not operate the appliance in direct sunlight, near heat sources, humid
environments or in places near water or other liquids such as bathrooms, showers
or swimming pools.
• Do not operate with wet hands or spill water or other liquids on to the appliance,
the mains cable or plug.
• Always unplug the appliance when not in use.
• Never leave the appliance unattended when in use.
• Some parts can become very hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
• The heater must not be located immediately below a mains socket.
• Do not allow children to play with the appliance or sit, stand, or climb on it.
• Do not leave children alone or unattended in the area where the appliance is in
use.
• For safety reasons a broken or damaged mains cable may only be replaced by the
manufacturer or a similarly qualied person.
• Children of less than 3 years old should be kept away unless continuously
supervised.
• Children aged from 3 years and less than 8 years shall only switch on/o the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• Do not block or restrict the airow around the appliance. Position the unit so that
the air inlet and exhaust grilles are not blocked or restricted in anyway.
• Do not push any objects in the air inlet and exhaust grilles.
WARNING
In order to avoid overheating, do not cover the appliance.
• Do not use the appliance with a programmer, timer or any other device that
switches the appliance on automatically. A re risk exists if the appliance is covered
or positioned incorrectly.
IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE
PERSONNEL TO CARRY OUT SERVICING OF REPAIRS WHICH INVOLVE THE
REMOVAL OF COVERS.
TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS
YOURSELF.
Notes for battery disposal
The batteries used with this product contain chemicals that are harmful to the environment. To preserve
our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of
batteries with normal household waste.
For more information, please contact the local authority or your retailer where you purchased the product.
DSG Retail Ltd. (co. no. 504877)
1 Portal Way, London, W3 6RS, UK
The symbol on the product or its packaging indicates that this product must not be disposed
of with your other household waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point for the recycling of waste
electrical and electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment.
For more information about where you can drop o your waste for recycling, please contact
your local authority, or where you purchased your product.
All trademarks are the property of their respective owners and all rights are acknowledged.
IB-L20CTH11-151201V4
Visit Partmaster.co.uk today for the easiest way to buy electrical spares and
accessories. With over 1 million spares and accessories available we can deliver
direct to your door the very next day. Visit www.partmaster.co.uk or call 0344 800
3456 (UK customers only). Calls charged at National Rate.
For general information about this appliance
and handy hints and tips, please visit
www.knowhow.com/knowledgebank or call 0344 5611234.
Instruction Manual
Ceramic Tower Heater
L20CTH11
Thank you for purchasing your new Logik Heater.
We recommend that you spend some time reading this instruction manual in
order that you fully understand all the operational features it oers. You will also
nd some hints and tips to help you resolve any issues.
Read all the safety instructions carefully before use and keep this instruction
manual for future reference.
L20CTH11_IB_RC_151201_grace.indd 1-3 1/12/15 2:36 pm
Product Overview
Unpacking
Remove all items from the packaging. Retain the packaging. If you dispose of it please do so
according to local regulations.
The following items are included:
Control Panel
Operation
Position the heater upright on the oor away from curtains, furniture or wall coverings before
plugging your heater into the mains socket.
• Connect the heater to the mains socket. Be sure the mains plug ts tightly in mains socket. A
loose t will cause overheating and damage the mains plug.
• Switch the heater on by turning the Power Switch, the power indicator will illuminate red.
• Adjust the Power Switch to set the function,
O mode: The heater is o.
Fan mode: The heating element is o, only the fan is operating.
The heater will blow cool air out from the air outlet.
Low Temp. mode: The heater is in economy mode.
High Temp. mode: The heater is in maximum power.
• To switch the heater o, turn the Power Switch to “O” position. The power indicator will
turn o. Remove the mains plug from mains socket.
Cleaning
Your heater should be cleaned regularly to prevent dirt and dust from building up which will
aect its performance. Ensure the air inlet and the air outlet are not blocked. This can be done
with a vacuum cleaner, using the brush attachment.
Hints & Tips
My heater does not work when I turn it on
• Check that your heater is plugged in and the power is turned on at the mains socket.
• The heater may be overheating. Switch it o and allow it to completely cool down for at
least 30 mins, then switch it on again.
• Turn the Power Switch to the “High Temp” position.
• Try replacing the BSI or ASTS approved 13 Amp BS1362 fuse in the plug.
• If the heater still doesn’t work, do not try to repair the heater yourself.
If your heater’s power is automatically cut o follow the steps
below:
1. Unplug your heater and allow it to cool down for at least 30 mins.
2. Inspect your heater.
3. Plug-in the heater and switch it on again. If it cuts o again, move the heater to a better
ventilated location.
4. If there is any sign of physical damage (e.g. melting, or burning of the case), do not attempt
to use your heater. Please leave all maintenance work to qualied personnel.
Installation
1. Guide the mains cable through the centre of the front base and connect the front base to
the main unit.
2. Fit the rear base onto the front base and the main unit.
3. Screw the four screws through base parts and into the main unit.
4. Attach the power cord guard over the power cord and to the rear
base.
• If items are missing or damaged, please contact Partmaster (UK only).
• Tel: 0344 800 3456 for assistance.
It is normal for the heater to emit some smell and fumes when it is turned on for the
rst time or when turned on after not being used for a long period of time. This smell
will disappear when the heater has been turned on for a short while.
Ensure you unplug your heater from the mains socket and wait for the heater to
cool down completely before cleaning.
The heater cannot be switched on when it is overheating. Allow it to cool down for
at least 30 mins and then switch it on again.
Safety Protective Devices
Overheat Protection System
The power to the heater will automatically cut o if the temperature of the heater exceeds a
certain limit. In the event of overheating, the heater will stop operating. Switch the heater o
and allow it to completely cool for at least 30 mins. The heater will then resume operating as
normal.
Oscillation Function
The heater is equipped with an oscillation feature. If you want to obtain a wider area of heat
circulation, turn the Oscillating Switch to the “On” position. To stop the oscillation, turn the
Oscillating Switch to the “O” position.
Screw x 4
Rear Base x 1
Front Base x 1
The Main Unit
Power Switch Oscillating Switch
Front Rear
Handle
Mains Cable
Rear Base
Front Base
Mains Cable
Slot
Mains Cable
Guard
Specications
Model L20CTH11
Mains supply 220-240V ~50Hz Class II
Power consumption 1900W (High), 1000W (Low), 30W (Fan)
Features and specications are subject to change without prior notice.
Air Inlet
Power Switch
Oscillating Switch
Power
Indicator
Air Outlet
Base
L20CTH11_IB_RC_151201_grace.indd 4-6 1/12/15 2:36 pm
/
