Emerson 1367 High-Pressure Instrument Supply System User manual

Brand: Emerson

Model: 1367 High-Pressure Instrument Supply System

Type: User manual

Type 1367

D100343X012

Instruction Manual

Form 5220

February 2013

www.fisherregulators.com

Type 1367 High-Pressure Instrument Supply

System with Overpressure Protection

WARNING

Failure to follow these instructions or

to properly install and maintain this

equipment could result in an explosion,

 re and/or chemical contamination

causing property damage and personal

injury or death.

Fisher

regulators must be installed,

operated, and maintained in accordance

with federal, state, and local codes, rules

and regulations, and Emerson Process

Management Regulator Technologies

Inc. instructions.

Figure 1. Type 1367 High-Pressure Instrument Supply System

If the regulator vents gas or a leak

develops in the system, service to

the unit may be required. Failure

to correct trouble could result in a

hazardous condition.

Installation, operation, and maintenance

procedures performed by unquali ed

personnel may result in improper

adjustment and unsafe operation. Either

condition may result in equipment

damage or personal injury. Use quali ed

personnel when installing, operating,

and maintaining the Type 1367 regulator.

W8649

TYPE H800

RELIEF VALVE

2ND-STAGE TYPE 67CF

FILTER-STYLE REGULATOR

1ST-STAGE

TYPE 1301F REGULATOR

TYPE 252

FILTER

INLET

Type 1367

Introduction

Scope of the Manual

This manual provides installation information on the

Type 1367 high-pressure instrument supply system.

For complete adjustment, maintenance, and parts

information on the individual components of this

system, refer to separate manuals for the Types 67CF

and 1301F regulators, Type 252 lter, and Type H800

relief valve. Refer to other manuals for actuator, valve

body, and instrument information.

Note

No instruction manual exists for the

Type H120 relief valve, as this relief

valve cannot be adjusted or repaired.

Any maintenance on the Type H120

relief valve must be accomplished by

replacing it as a complete unit.

Product Description

The Type 1367 high-pressure instrument supply

system takes a pressure of up to 2000 psig / 138 bar

and reduces it to a controlled pressure to be used

for supplying a pneumatic instrument. This system

consists of the following lters, regulators, and

relief valves:

• A Type 252 extended body lter with drain valve.

• A rst-stage Type 1301F regulator with mounting

bracket for an actuator yoke or casing.

Specications

The Specications table lists general Type 1367 instrument supply system specications, while a nameplate wired

to one of the pipe nipples gives the maximum inlet pressure and date of manufacture.

1. The pressure/temperature limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.

Connection Size

Inlet and Outlet: 1/4 NPT

Type H800 Vent: 1/2 NPT with removable screen

Maximum Inlet Pressure

(1)

2000 psig / 138 bar

Fixed Relief Setting of Type H120 Relief Valve

150 psig / 10.3 bar

Outlet (Supply) Pressure Range

5 to 70 psig / 0.35 to 4.8 bar

Maximum Outlet (Supply) Pressure with Type 67CF

Regulator Failed Wide-Open with:

Type H800 Relief Valve Relieving: 50 psig / 3.4 bar

Type H120 (Second Stage) Relief Valve Relieving:

90 psig / 6.2 bar

Temperature Capabilities

(1)

-20 to 150°F / -29 to 66°C

Approximate Weight

12 pounds / 5.4 kg

• A Type H120 relief valve mounted in the side outlet

of the Type 1301F regulator.

• A second-stage Type 67CF lter-style regulator,

mounted on the Type 1301F regulator.

• A Type H800 or H120 relief valve nipple-mounted in

the outlet of the Type 67CF regulator.

Principle of Operation

The Type 252 lter helps remove dirt, rust, chips,

scale, and moisture from the incoming high-pressure

supply before it enters the Type 1301F regulator. The

Type 1301F regulator is set to reduce this incoming

high-pressure to 100 psig / 6.9 bar. The reduced

pressure from the Type 1301F regulator is then further

reduced between 20 and 70 psig / 1.4 or 4.8 bar

to supply the pneumatic instrument. Although the

Type 67CF regulator is normally set for 20 psig /

1.4 bar outlet pressure, it can be eld-adjusted up to

35 psig / 2.4 bar outlet pressure.

The rst stage Type H120 relief valve serves to protect

the Type 67CF regulator by relieving if the reduced

pressure from the Type 1301F regulator exceeds

150 psig / 10.3 bar. The Type H800 or H120 relief

valve serves to protect downstream equipment from

overpressure by relieving if the reduced pressure

from the Type 67CF regulator exceeds the relief

setpoint. Air or gas owing from one or both of the

relief valves indicates that one or both of the regulators

are worn or damaged and must be repaired or

replaced immediately.

Type 1367

Figure 2. Type 1367 Operational Schematic

HIGH INLET PRESSURE

ATMOSPHERIC PRESSURE

INITIAL STEP-DOWN PRESSURE, 100 psig / 6.9 bar

FINAL OUTLET PRESSURE, 10 to 35 psig / 0.69 to 2.4 bar

RELIEF PRESSURE

TYPE H120 RELIEF VALVE NOT SHOWN

TYPE 252

TYPE 1301F

TYPE 67CF

TYPE H800

HIGH INLET PRESSURE

ATMOSPHERIC PRESSURE

INITIAL STEP-DOWN PRESSURE, 100 psig / 6.9 bar

FINAL OUTLET PRESSURE, 10 to 35 psig / 0.69 to 2.4 bar

RELIEF PRESSURE

FIRST STAGE TYPE H120 RELIEF VALVE NOT SHOWN

TYPE 252

TYPE 1301F

TYPE 67CF

TYPE H120

Type 1367

Installation

All key numbers mentioned in this section appear

in Figure 2.

WARNING

Installing a Type 1367 instrument supply

system where its capabilities can be

exceeded or where proper operation

might be impaired may cause personal

injury, property damage, or leakage due

to bursting of pressure-containing parts

or explosion of accumulated gas. To

avoid such conditions:

• Use qualied service person to

install the Type 1367 instrument

supply system.

• Install the Type 1367 instrument

supply system where it is protected

from exposure to physical damage

and/or corrosive substances.

• Install the instrument supply system

where service conditions are within

the unit capabilities specied in

Specications. Consult your local

Sales Ofce if service conditions

exceed Specications capabilities.

Consult local Sales Ofce if

service conditions exceed

Specications capabilities.

Impairment of proper operation includes

permanently removing the Types H120

and H800 relief valves from their

respective regulators and plugging the

side outlet of the Type 1301F regulator.

Note

If the Type 1367 instrument supply

system is shipped mounted on another

unit, install that unit according to the

appropriate instruction manuals.

With an instrument supply system that is

shipped separately:

1. Make sure that there is no damage to

the components.

2. Mount the bracket of the Type 1301F regulator

(key 2) on the actuator yoke or casing.

Note

If using pipe in the following steps,

apply thread tape or pipe compound

to the pipe threads before making

the connections.

3. Install tubing or piping into the 1/4 NPT inlet

connection of the Type 252 lter (key 1) so that

ow is in the proper direction as indicated on the

lter head.

4. Install tubing or piping from the 1/4 NPT

outlet (or side) connection of the Type H800 or

tee of the Type H120 relief valve (key 5) to the

pneumatic instrument.

WARNING

An instrument supply system may

vent some gas to the atmosphere. In

hazardous or ammable gas service,

vented gas may accumulate, causing

personal injury, death, or property

damage due to re or explosion. Vent a

supply system in hazardous gas service

to a remote, safe location away from air

intakes or any hazardous location. The

vent lines in both of the following steps

must be protected against condensation

or clogging.

5. To remotely vent gas from the 1/2 NPT vent (or

bottom) connection of the Type H800 relief valve

(key 5), remove the screen from the Type H800

vent. Then install the appropriate size piping or

tubing into the Type H800 vent connection. The

piping or tubing should vent the gas to a safe

location, be as short and have as few bends as

possible to minimize backpressure during relief

valve operation, and have a screened vent on

its exhaust end. Install any remote vent piping

or tubing so that the vent is protected from

condensation, freezing, or any substance that

could clog it.

6. To remotely vent gas from the 1/4 NPT connection

of the street elbow (key 7) or the pipe tee (key 10),

remove the Type H120 relief valve (key 3 and/

or key 5) from the elbow or tee. Then install the

appropriate size piping or tubing into the elbow.

The piping or tubing should vent the gas to a safe

location, and be as short as possible and have as

Type 1367

few bends as possible to minimize backpressure

during relief valve operation. Reinstall the

Type H120 relief on the remote end of the piping

or tubing installed in the elbow.

Startup

With installation completed and downstream

equipment adjusted, slowly open the upstream and

downstream block valves while using pressure gauges

to monitor pressure.

Adjustments

Unless specied otherwise, each instrument supply

system is factory-set for a 20 psig / 1.34 bar outlet

pressure. Consult the Types 67CF and 67CFR

regulators instruction manual for the procedure to

adjust the Type 67CF regulator (key 4, Figure 2)

anywhere within its 5 to 70 psig / 0.35 to 4.8 bar outlet

pressure range.

Shutdown

First, close the upstream shutoff valve, and then,

close the downstream shutoff valve. Next, open the

vent valve between the regulator and the downstream

shutoff valve and open the vent valve between the

regulator and the upstream shutoff valve. If vent

valves are not installed, safely bleed off both inlet and

outlet pressures and check that the regulator contains

no pressure.

Maintenance

All key numbers mentioned in this section appear

in Figure 2.

Type 1367 instrument supply systems parts are

subject to normal wear and must be inspected and

replaced as necessary. The frequency of inspection

and parts replacement depends on the severity of

service conditions and the requirements of local,

state, and federal rules and regulations. The drain

valves of both the Types 252 and 67CF regulators

(keys 1 and 4) should be opened periodically to empty

accumulated moisture.

Consult the appropriate instruction manual for

maintenance procedures on each of the components

of the Type 1367 instrument supply system.

WARNING

To avoid personal injury or equipment

damage from sudden release of

pressure or explosion of accumulated

gas, do not attempt any maintenance

or disassembly without rst isolating

the instrument supply system and

associated equipment from system

pressure and relieving all internal

pressure from the instrument supply

system and associated equipment.

To avoid personal injury or equipment

damage due to impaired operation, make

sure that the relief valves (keys 3 and 5)

are directly or remotely installed into

the appropriate outlets of the regulators

(keys 2 and 4) after maintenance

is completed.

Parts Ordering

When corresponding with your local Sales Ofce

about this unit, include the date of manufacture from

the nameplate and the type numbers and all other

pertinent information from the nameplates and other

identication appearing on each of the components.

Specify the appropriate part number when ordering

any new parts from the following list.

Parts List

To Provide Sour Gas Corrosion

Resistance Capability

(1)

Key Description Part Number

1 Type 252 Filter FS252-8

(2)

2 Type 1301F Regulator

For yoke mounting FS1301F-N2/M1

(2)

For casing mounting FS1301F-N2/M3

(2)

3 Type H120 Relief Valve FSH120-N150

4 Type 67CF Regulator FS67CF-N206

(2)

5 Type H800 Relief Valve FSH800-2

(2)

6 Pipe Nipple, Plated Carbon steel (3 required) - - - - - - - - - - -

7 Street Elbow, Heat-treated steel - - - - - - - - - - -

8 Nameplate, Stainless steel (not shown) - - - - - - - - - - -

9 Wire, Monel

with Lead seal (not shown) T12315T0012

1. As detailed in NACE international standard MR0175.

2. For entire assembly. See separate manual for individual part numbers.

Monel

is a trademark of Special Metals Corporation.

Type 1367

A7036

Figure 3. Type 1367 Instrument Supply System Assembly

3 6

TYPE H120 RELIEF VALVE NOT SHOWN

FIRST STAGE TYPE H120 RELIEF VALVE NOT SHOWN

Type 1367

For Other Than Sour Gas Corrosion

Resistance Applications

With Type H800

Key Description Part Number

1 Type 252 Filter FS252-8

(2)

2 Type 1301F Regulator

For yoke mounting FS1301F-2/M1

(2)

For casing mounting FS1301F-2/M3

(2)

3 Type H120 Relief Valve FSH120-150

4 Type 67CF Regulator FS67CF-206

(2)

5 Type H800 Relief Valve FSH800-2

(2)

6 Pipe Nipple, Zinc-plated

Galvanized steel (3 required) - - - - - - - - - - -

7 Street Elbow, Galvanized plated

Malleable iron - - - - - - - - - - -

8 Nameplate, Stainless steel (not shown) - - - - - - - - - - -

9 Wire, Monel

with Lead seal (not shown) T12315T0012

With Type H120

Key Description Part Number

1 Type 252 Filter FS252-4S

2 Type 1301F Regulator

For yoke mounting FS1301F-N5/M1

(2)

For casing mounting FS1301F-N5/M1

(2)

3 Type H120 Relief Valve FSH120-SS150

4 Type 67CFS Regulator FS67CFS-226

5 Type H120 Relief Valve FSH120-40

FSH120-50

FSH120-60

FSH120-70

FSH120-75

6 Pipe nipple, Stainless steel (3 required) - - - - - - - - - - -

7 Street Elbow, Stainless steel - - - - - - - - - - -

8 Nameplate, Stainless steel (not Shown) - - - - - - - - - - -

9 Wire, Monel

with lead seal (not shown) - - - - - - - - - - -

10 Pipe tee, Stainless steel - - - - - - - - - - -

2. For entire assembly. See separate manual for individual part numbers.

Monel

is a trademark of Special Metals Corporation.

Type 1367

The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls International LLC,

a business of Emerson Process Management.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or

guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specications of such

products at any time without notice.

Emerson Process Management Regulator Technologies, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and

maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.

Industrial Regulators

Emerson Process Management

Regulator Technologies, Inc.

USA - Headquarters

McKinney, Texas 75069-1872, USA

Tel: +1 800 558 5853

Outside U.S. +1 972 548 3574

Asia-Pacic

Shanghai 201206, China

Tel: +86 21 2892 9000

Europe