Pioneer DEQ-P7000 User manual

English

Español

Deutsch

Français

Italiano

Nederlands

Multi-channel AV processor

Processeur AV multi-canaux

Operation Manual

DEQ-P7000

Mode d’emploi

Before You Start
About this unit 3
• Dolby Digital/DTS compatibility (when
combining this unit with a Pioneer DVD
player such as DVH-P7000R) 3
About this manual 3
Precautions 3
In case of trouble 3
Resetting the microprocessor 4
Output setting of the DVD player 4
What’s what 5
• Head Unit 5
Audio Adjustments
Introduction of audio adjustments 6
• Operating the audio menu 6
• Operating the audio details menu 6
Using the sound field control 7
Using the position selector 7
Using balance adjustment 8
Adjusting source levels 8
Using the dynamic range control 9
Using the dual mono mode 9
Using the direct control 9
Using the Dolby Pro Logic 9
Setting the speaker setting 10
• Correcting the subwoofer’s phase 10
Selecting a cut-off frequency 11
Adjusting the speaker output levels 11
Adjusting the speaker output levels using a
test tone 12
Adjusting the time alignment 13
Using the equalizer 13
• Recalling equalizer curves 13
• Adjusting 3-band parametric equalizer
14
Initial Settings
Correcting distorted sound 15
Additional Information
Troubleshooting 16
• Common 16
• Audio/DSP 17
• DVD player setting 17
Terms 18
Specifications 19
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to oper-
ate your model properly. After you have finished reading the instructions, put them
away in a safe place for future reference.
Contents
En
2
00
Section

Before You Start

En

3

About this unit

Dolby* Digital/DTS** compatibility (when

combining this unit with a Pioneer DVD

player such as DVH-P7000R)

When using this unit with a Pioneer DVD player,

you can enjoy the atmosphere and excitement

provided by DVD movie and music software

featuring 5.1 channel recordings.

* Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the dou-

ble-D symbol are trademarks of Dolby

Laboratories.

** “DTS” and “DTS Digital Surround” are regis-

tered trademarks of Digital Theater Systems,

Inc.

About this manual

This unit features a number of sophisticated

functions ensuring superior reception and oper-

ation. All the functions have been designed for

the easiest possible use, but many are not self-

explanatory. This operation manual will help you

benefit fully from this unit's potential and to

maximize your listening enjoyment.

We recommend that you familiarize yourself

with the functions and their operation by read-

ing through the manual before you begin using

this unit. It is especially important that you read

and observe the precautions listed on this page

and in other sections.

Precautions

• Keep this manual handy as a reference for

operating procedures and precautions.

• Always keep the volume low enough so you

can hear sounds outside of the car.

• Protect this unit from moisture.

• If the battery is disconnected or discharged,

the preset memory will be erased and must be

reprogrammed.

In case of trouble

Should this unit fail to operate properly, contact

your dealer or nearest authorized Pioneer

Service Station.

This product complies with the EMC

Directives (89/336/EEC, 92/31/EEC) and

CE Marking Directive (93/68/EEC).

English

Español

Deutsch

Français

Italiano

Nederlands

01

Section

Before You Start

En

4

01

Section

Resetting the microprocessor

The microprocessor must be reset under the

following conditions:

• Prior to using this unit for the first time after

installation.

• If the unit fails to operate properly.

• When strange or incorrect messages appear

on the display.

• To reset the microprocessor, press the

RESET button on the unit with a pen tip or

other pointed instrument.

Output setting of the DVD player

When connecting Pioneer DVD player such as

DVH-P7000R, make DIGITAL OUTPUT

(Setting for digital output) and OUTPUT

SELECTION (Setting digital and analog audio

output) as follows:

Function Setting

DIGITAL OUTPUT Dolby D/LPCM

OUTPUT SELECTION 48KHz

Refer to the DVD player manual for details on

how to make those settings.

Important

• Be sure to set the correct position. If not, no

audio can be outputted.

Before You Start

En

5

English

Español

Deutsch

Français

Italiano

Nederlands

01

Section

What’s what

Operate this unit with the connected head unit.

Instructions in this operation manual use DVH-

P7000R as an example head unit.

Head Unit

1 VOLUME

Turn to adjust the volume.

When you press the VOLUME, it extends

outward so that it becomes easier to turn.

To retract the VOLUME, press it again.

2 FUNCTION button

Press to select functions.

3 AUDIO button

Press to select an audio function.

4 5/∞/2/3 buttons

Press to adjust the selected audio function

and turn it on or off.

5 SFEQ/SFC button

Press to select a sound field control.

6 BAND/ESC button

Press to return to the display of each source.

7 SOURCE button

This unit is switched on by selecting a

source. Press to cycle through all of the

available sources. Press and hold to turn off

the unit.

8 EQ button

Press to select an equalizer curve.

1

3

4

5678

2

Audio Adjustments

Introduction of audio adjustments

By carrying out the following settings/adjust-

ments in order, you can create a finely-tuned

sound field effortlessly.

1 Setting the speaker setting

2 Using the position selector

3 Adjusting the time alignment

4 Adjusting the speaker output levels using a

test tone

5 Selecting a cut-off frequency

6 Adjusting the speaker output levels

7 Adjusting 3-band parametric equalizer

Operating the audio menu

1 AUDIO display

Shows the audio adjustments status.

2 Subwoofer indicator

Appears in the display when the subwoofer

output is turned on.

Press AUDIO to display the audio function

names.

Press AUDIO repeatedly to switch between the

following audio functions:

Posi (position selector)—Fad (balance adjust-

ment)—SLA (source level adjustment)—DRC

(dynamic range control)—D.MONO (dual

monaural)—DIRECT (direct)—DolbyPL

(Dolby Pro Logic)

• When selecting the FM tuner as the source,

you cannot switch to SLA.

• When playing other than the DVD disc, you

cannot switch to DRC or D.MONO.

• To return to the playback display, press

BAND/ESC.

Note

• If you do not operate the audio function within

about 30 seconds, the display is automatically

returned to the source display.

Operating the audio details menu

1 Front left speaker

2 Center speaker

3 Front right speaker

4 Rear left speaker

5 Subwoofer

6 Rear right speaker

Press AUDIO and hold until SP Set appears

in the display, then press AUDIO to display

the audio function names.

After SP Set is displayed, press AUDIO repeat-

edly to switch between the following audio func-

tions:

123

456

12

En

6

02

Section

Audio Adjustments

En

7

SP Set (speaker setting)—CutOff (cut-off fre-

quency)—SP Lev (speaker output

level)—T Tone (test tone)—Time A (time align-

ment)—PEQ (3-band parametric equalizer)

• When neither F/L nor F/R is selected in Posi,

you cannot switch to Time A.

• When neither CUSTOM1 nor CUSTOM2 is

selected as equalizer curve, you cannot switch

to PEQ.

• To return to the playback display, press

BAND/ESC.

Using the sound field control

The SFC function creates the sensation of a live

performance.

• The acoustics of different performance envi-

ronments are not the same and depend on the

extent and contour of space through which

sound waves move and on how sounds bounce

off the stage, walls, floors and ceilings. At a live

performance you hear music in three stages:

direct sound, early reflections, and late reflec-

tions, or reverberations.

Those factors are programed into the SFC cir-

cuitry to recreate the acoustics of various per-

formance settings.

Press SFEQ/SFC to select the desired SFC

mode.

Press SFEQ/SFC repeatedly to switch between

the following mode:

Musical (musical)—Drama (drama)—Action

(action)—Jazz (jazz)—Hall (hall)—Club

(club)—OFF (off)

Note

• If the source is a 2-channel LPCM audio or a

2-channel Dolby Digital audio and you select

SFC effects that are most applicable for 5.1-

channel audio (i.e., Musical, Drama or

Action), we recommend switching Dolby Pro

Logic on. On the other hand, when selecting

SFC effects that are intended for use with 2-

channel audio (i.e., Jazz, Hall or Club), we

recommend switching Dolby Pro Logic off.

Using the position selector

One way to assure a more natural sound is to

clearly position the stereo image, putting you

right in the center of the sound field. The posi-

tion selector function lets you automatically

adjust the speaker output levels and inserts a

delay time to match the number and position of

occupied seats. When used in conjunction with

the SFC, the feature will make the sound image

more natural and offer a panoramic sound that

envelops you.

1 Press AUDIO to select Posi.

Press AUDIO until Posi appears in the display.

2 Press 5/∞/2/3 to select a listening posi-

tion.

Press one of these, 2/3 /5/∞, to select a listen-

ing position as listed in the table.

Button Display Position

2 F/L Front seat left

3 F/R Front seat right

5 FRONT Front seats

∞ ALL All seats

• To cancel the selected listening position,

press the same button again.

English

Español

Deutsch

Français

Italiano

Nederlands

02

Section

Audio Adjustments

Note

• When you make adjustments for listening

position, the speakers are automatically set

for appropriate output levels. You can tailor

them if you want as discussed under the

heading of Adjusting the speaker output levels

using a test tone or Adjusting the speaker

output levels.

Using balance adjustment

You can select a fader/balance setting that pro-

vides an ideal listening environment in all occu-

pied seats.

1 Press AUDIO to select Fad.

Press AUDIO until Fad appears in the display.

• If the balance setting has been previously

adjusted, Bal will be displayed.

2 Press 5 or ∞ to adjust front/rear speaker

balance.

Each press of 5 or ∞ moves the front/rear

speaker balance to the front or the rear.

• Fad F25 – Fad R25 is displayed as the

front/rear speaker balance moves from front to

rear.

• Fad F/R 0 is the proper setting when only two

speakers are used.

3 Press 2 or 3 to adjust left/right speaker

balance.

When you press 2 or 3, Bal L/R 0 is displayed.

Each press of 2 or 3 moves the left/right

speaker balance to the left or the right.

• Bal L25 – Bal R25 is displayed as the

left/right speaker balance moves from left to

right.

Adjusting source levels

SLA (source level adjustment) lets you adjust

the volume level of each source to prevent radi-

cal changes in volume when switching between

sources.

• Settings are based on the FM tuner volume

level, which remains unchanged.

1 Compare the FM tuner volume level with

the level of the source you want to adjust.

2 Press AUDIO to select SLA.

Press AUDIO until SLA appears in the display.

3 Press 5 or ∞ to adjust the source volume.

Each press of 5 or ∞ increases or decreases

the source volume.

• SLA +4 – SLA –4 is displayed as the source

volume is increased or decreased.

Notes

• Since the FM tuner volume is the control, it is

not possible to apply source level adjustments

to the FM tuner.

• The MW/LW tuner volume level can also be

adjusted with source level adjustments.

• Video CD and CD are set to the same volume

adjustment setting automatically.

• External unit 1 and external unit 2 are set to

the same volume adjustment setting automat-

ically.

En

8

02

Section

Audio Adjustments

En

9

Using the dynamic range control

The dynamic range refers to the difference

between the largest and softest sounds. The

dynamic range control compresses this differ-

ence so that you can clearly hear sounds even

at low volume levels.

1 Press AUDIO to select DRC.

Press AUDIO until DRC appears in the display.

2 Press 5 to turn the dynamic range control

on.

DRC ON appears in the display. Dynamic range

control is now on.

• You can turn off dynamic range control by

pressing ∞.

Notes

• The dynamic range control is effective only on

Dolby Digital sounds.

• When playing other than the DVD disc, you

cannot switch this mode.

Using the dual mono mode

When playing a disc recorded on a dual mono

mode, you can select the channel to output.

1 Press AUDIO to select D.MONO.

Press AUDIO until D.MONO appears in the

display.

2 Press 2 or 3 to select the desired output

setting.

Press 2 or 3 until the desired output setting

appears in the display.

L&R (left and right channels)—Lch(left chan-

nel)—R ch (right channel)

Notes

• This function is effective only on dual mono

mode sound.

• When playing other than the DVD disc, you

cannot switch this mode.

Using the direct control

You can override audio settings to check for

effectiveness of your audio settings.

1 Press AUDIO to select DIRECT.

Press AUDIO until DIRECT appears in the

display.

2 Press 5 to turn the direct control on.

DIRECT ON appears in the display. Direct

control is now on.

• You can turn off direct control by pressing ∞.

Note

• All audio functions are locked out during

DIRECT ON except VOLUME.

Using the Dolby Pro Logic

Dolby Pro Logic gives enhanced spatial and

directional effects, creating theater-like sense of

presence and ambience.

• If the source is a 2-channel LPCM audio or a

2-channel Dolby Digital audio and you select

SFC effects that are most applicable for 5.1-

channel audio (i.e., Musical, Drama or

Action), we recommend switching Dolby Pro

Logic on. On the other hand, when selecting

SFC effects that are intended for use with 2-

channel audio (i.e., Jazz, Hall or Club), we

recommend switching Dolby Pro Logic off.

English

Español

Deutsch

Français

Italiano

Nederlands

02

Section

Audio Adjustments

1 Press AUDIO to select DolbyPL.

Press AUDIO until DolbyPL appears in the

display.

2 Press 5 to turn the Dolby Pro Logic on.

DolbyPL ON appears in the display. Dolby Pro

Logic is now on.

• You can turn off Dolby Pro Logic by pressing

∞.

Note

• When playing a 2-channel mono source with

Pro Logic switched on, there may be occa-

sions when the following will occur:

No audio is outputted if the center speaker

setting is SMALL or LARGE while no center

speaker is installed.

Audio is heard only over the center speaker if

installed and the center speaker setting is

SMALL or LARGE.

Setting the speaker setting

You need to make with/without (or yes/no) and

size (bass reproducing capacity)

selection/adjustments depending on the

installed speakers. The size needs to be set to

LARGE (large) if the speaker is capable of

reproducing sounds of about 100 Hz or below.

Otherwise select SMALL (small).

1 Press AUDIO and hold until SP Set

appears in the display.

2 Press 2 or 3 to select the speaker to be

adjusted.

Each press of 2 or 3 selects the speaker in the

following order:

Front speakers—Center speaker—Rear speak-

ers—Subwoofer—S.W (subwoofer setting)

• You can switch to the S.W, only when the

subwoofer has been set to ON.

3 Press 5 or ∞ to select the correct size for

the selected speaker.

Press 5 or ∞ until the desired size appears in

the display.

LARGE (large)—SMALL (small)—OFF (off)

• You cannot select OFF, when the front speak-

ers have been selected.

• You can switch ON or OFF, when the sub-

woofer has been selected.

• You can switch Rev. (reverse phase) or

Normal (normal phase), when S.W (subwoofer

setting) has been selected.

4 Press BAND/ESC to return to the playback

display.

Correcting the subwoofer’s phase

If trying to boost the bass output of the sub-

woofer doesn’t do much or rather makes you

feel that the bass gets more murky, this may

indicate that the subwoofer’s output and bass

content you hear over other speakers cancel

each other out. To remove this problem, try

changing the phase setting for the subwoofer.

1 Press AUDIO and hold until SP Set

appears in the display.

2 Press 2 or 3 to select the subwoofer.

Press 2 or 3 selects the speaker in the follow-

ing order:

Front speakers—Center speaker—Rear speak-

ers—Subwoofer—S.W (subwoofer setting)

En

10

02

Section

Audio Adjustments

En

11

3 Press 5 to turn the subwoofer output on.

4 Press 3 to select S.W (subwoofer setting).

5 Press 5 or ∞ to select the subwoofer out-

put phase.

Press 5 to select Normal (normal phase).

Press ∞ to select Rev. (reverse phase).

6 Press BAND/ESC to return to the playback

display.

Important

• Low frequency range is not outputted if the

subwoofer is set to OFF and the front and rear

speakers set to SMALL or OFF.

Notes

• It is imperative that non-installed speakers be

set to OFF.

• Set the front or rear speaker to LARGE if the

speaker is capable of reproducing bass con-

tent, or if no subwoofer is installed.

• When playing a 2-channel mono source with

Pro Logic switched on, there may be occa-

sions when the following will occur:

No audio is outputted if the center speaker

setting is SMALL or LARGE while no center

speaker is installed.

Audio is heard only over the center speaker if

installed and the center speaker setting is

SMALL or LARGE.

Selecting a cut-off frequency

You can select a frequency, under which sounds

are reproduced through the subwoofer.

If the installed speakers include one whose size

has been set to SMALL, you can select a fre-

quency, under which sounds are reproduced

through a LARGE speaker or subwoofer.

1 Press AUDIO and hold until SP Set

appears in the display, then press AUDIO to

select CutOff.

After SP Set is displayed, press AUDIO until

CutOff appears in the display.

2 Press 2 or 3 to select the cut-off

frequency.

Each press of 2 or 3 selects the cut-off fre-

quency in the following order:

63—80—100—125—160—200 (Hz)

• Press 2 or 3 until the desired frequency

appears in the display.

3 Press BAND/ESC to return to the playback

display.

Note

• Selecting a cut-off frequency is to set a cut-off

frequency of the subwoofer’s L.P.F. (low-pass

filter) and that of the SMALL speaker H.P.F.

(high-pass filter). Cut-off frequency setting

has no effect if the subwoofer is set to OFF

and any other speaker is set to LARGE or

OFF.

Adjusting the speaker output

levels

You can readjust the speaker output levels once

adjusted using a test tone while listening to

music at the time.

1 Press AUDIO and hold until SP Set

appears in the display, then press AUDIO to

select SP Lev.

After SP Set is displayed, press AUDIO until

SP Lev appears in the display.

English

Español

Deutsch

Français

Italiano

Nederlands

02

Section

Audio Adjustments

2 Press 2 or 3 to select the speaker to be

adjusted.

Each press of 2 or 3 selects the speaker in the

following order:

Front speaker left—Center speaker—Front

speaker right—Rear speaker right—Rear

speaker left—Subwoofer

• You cannot select speakers whose size is set

OFF.

3 Press 5 or ∞ to adjust the speaker output

level.

Each press of 5 or ∞ increases or decreases

the speaker output level.

• +10 — –10 is displayed as the level is

increased or decreased.

4 Press BAND/ESC to return to the playback

display.

Note

• To adjust the speaker output levels at this

mode is the same as making the speaker

output levels at T Tone. Both provide the

same results.

Adjusting the speaker output

levels using a test tone

A convenient test tone allows you to easily get

the overall balance right among the speakers.

1 Press AUDIO and hold until SP Set

appears in the display, then press AUDIO to

select T Tone.

After SP Set is displayed, press AUDIO until T

Tone appears in the display.

2 Press 3 to start the test tone output.

The test tone is outputted. It rotates from

speaker to speaker in the following sequence at

intervals of about 2 seconds. The current set-

tings for the speaker over which you hear the

test tone are shown in the display.

Front speaker left—Center speaker—Front

speaker right—Rear speaker right—Rear

speaker left—Subwoofer

Check each speaker output level. If no adjust-

ments are needed, perform step 4 to stop the

test tone.

• The settings do not appear for speakers

whose size is set OFF.

3 Press 5 or ∞ to adjust the speaker output

level.

Each press of 5 or ∞ increases or decreases

the speaker output level.

• +10 — –10 is displayed as the level is

increased or decreased.

• The test tone rotates to the next speaker after

about 2 seconds from the last operation.

4 Press 2 to stop the test tone output.

5 Press BAND/ESC to return to the playback

display.

Notes

• If needed, select speakers and adjust their

‘absolute’ output levels, see Adjusting the

speaker output levels on page 11.

• To adjust the speaker output levels at this

mode is the same as making the speaker

output levels at SP Lev. Both provide the

same results.

En

12

02

Section

Audio Adjustments

En

13

Adjusting the time alignment

By adjusting the distance between each

speaker and a selected listening position, you

can insert delay times into the speaker output to

obtain a correct sound image and overall level

balance. Although this is automatically

achieved when you set the listening position,

the time alignment feature provides a fine

adjustment.

1 Press AUDIO and hold until SP Set

appears in the display, then press AUDIO to

select Time A.

After SP Set is displayed, press AUDIO until

Time A appears in the display.

• You cannot select Time A when neither F/L

nor F/R is selected in Posi.

2 Press 2 or 3 to select the speaker to be

adjusted.

Each press of 2 or 3 selects the speaker in the

following order:

Front speaker left—Center speaker—Front

speaker right—Rear speaker right—Rear

speaker left—Subwoofer

• You cannot select speakers whose size is set

OFF.

3 Press 5 or ∞ to adjust the distance

between the selected speaker and the listen-

ing position.

Each press of 5 or ∞ increases or decreases

the distance.

• 500.0cm — 0.0cm is displayed as the dis-

tance is increased or decreased.

4 Press BAND/ESC to return to the playback

display.

Using the equalizer

The parametric equalizer lets you adjust the

equalization to match car interior acoustic char-

acteristics as desired.

Recalling equalizer curves

There are seven stored equalizer curves which

you can easily recall at any time. Here is a list of

the equalizer curves:

Display Equalizer curve

SUPER BASS Super bass

POWERFUL Powerful

NATURAL Natural

VOCAL Vocal

FLAT Flat

CUSTOM1, 2 Custom1, 2

• CUSTOM1 and CUSTOM2 are adjusted

equalizer curves that you can create for your-

self.

• When FLAT is selected no supplement or

correction is made to the sound. This is useful

to check the effect of the equalizer curves by

switching alternatively between FLAT and a set

equalizer curve.

Press EQ to select the equalizer.

Press EQ repeatedly to switch between the

following equalizer.

POWERFUL—NATURAL—VOCAL—

FLAT—CUSTOM1—CUSTOM2—SUPER

BASS

English

Español

Deutsch

Français

Italiano

Nederlands

02

Section

Audio Adjustments

Adjusting 3-band parametric equalizer

For CUSTOM1 and CUSTOM2 equalizer

curves, you can adjust the front, rear and center

equalizer curves separately by selecting a cen-

ter frequency, an equalizer level and a Q factor

for each band.

• A separate CUSTOM1 curve can be created

for each source.

•A CUSTOM2 curve can be created common

to all sources.

• The center speaker largely determines the

sound image and getting the balance right isn’t

easy. We recommend reproducing a 2-ch. audio

(a CD for example) and getting the balance right

among the speakers except for the center, and

then reproducing a 5.1-ch. audio (Dolby Digital

or DTS) and adjusting the center speaker output

to the balance you have already got among the

other speakers.

1 Press AUDIO and hold until SP Set

appears in the display, then press AUDIO to

select PEQ.

After SP Set is displayed, press AUDIO until

PEQ appears in the display.

• You cannot select PEQ when neither CUS-

TOM1 nor CUSTOM2 equalizer curve is

selected.

2 Press 2 or 3 to select the speaker selec-

tion mode.

Each press of 2 or 3 selects the item in the

following order:

FRONT (speakers)—Low (bands)—Low (cen-

ter frequency)—L (equalizer level)—Q.WIDE (Q

factor)

3 Press 5 or ∞ to select the speaker to be

adjusted.

Each press of 5 or ∞ selects the speaker in the

following order:

FRONT (front speakers)—CENTER (center

speaker)—REAR (rear speakers)

• You cannot select speakers whose size is set

OFF.

4 Press 3 and then press 5 or ∞ to select the

equalizer band to be adjusted.

Each press of 5 or ∞ selects the equalizer band

in the following order:

Low (low)—Mid (mid)—High (high)

5 Press 3 and then press 5 or ∞ to select the

center frequency of selected band.

Each press of 5 or ∞ selects the frequency in

the following order:

100—125—160—200—250—315—400—500—

630—800—1k—1.25k—1.6k—2k—2.5k—

3.15k—4k—5k—6.3k—8k (Hz)

6 Press 3 and then press 5 or ∞ to adjust

the equalizer level.

Each press of 5 or ∞ increases or decreases

the equalizer level.

• +6 — –6 is displayed as the level is increased

or decreased.

7 Press 3 and then press 5 or ∞ to select the

desired Q factor.

Each press 5 or ∞ switches between the follow-

ing Q factor:

Q.WIDE (wide)—Q.NAR. (narrow)

• You can adjust parameters for each band of

the other speakers in the same way.

8 Press BAND/ESC to return to the playback

display.

Note

• You can select a center frequency from

among 20 frequencies for each band. You can

change the center frequency in 1/3-octave

steps, but you cannot select frequencies so

that there are intervals shorter than 1 octave

among the three bands’ center frequencies.

En

14

02

Section

Initial Settings

En

15

Correcting distorted sound

You can minimize distortion likely caused by the

equalizer curve settings.

• Setting an equalizer level high can cause

distortion. If high sound crippled or distorted,

try switching to Low. Normally, leave the setting

at High to ensure quality sound.

1 Press SOURCE and hold until this unit

turns off.

2 Press FUNCTION and hold until a function

name appears in the display.

3 Press FUNCTION to select D.ATT.

Press FUNCTION until D.ATT appears in the

display.

4 Press 2 or 3 to select Low or High.

Pressing 2 or 3 switches between Low (low)

and High (high) and that status is displayed.

• To cancel initial settings, press BAND/ESC.

• You can also cancel initial settings by holding

down FUNCTION until the unit turns off.

English

Español

Deutsch

Français

Italiano

Nederlands

03

Section

Additional Information

En

16

04

Section

Troubleshooting

Common

Symptom Cause Remedy

The power switch does not work.

No functions come on.

No sounds are heard.

The volume level will not rise.

Sound is not heard over a specific

speaker.

Cables or connectors are not

correctly connected.

The fuse is blown.

Cables are not connected

correctly.

The front, rear, left and right

speakers are not properly

adjusted in level balance.

The speaker size is set to OFF.

The speaker level is set to too

low.

The center speaker size is set

to SMALL or LARGE whereas

no center speaker is installed.

Check whether the cables are plugged in

correctly and firmly.

Remove the cause of the blowing of the

fuse, then replace the fuse. Be very sure

the same rated proper fuse is installed.

Connect the cables correctly.

Adjust the relative levels between the

speakers correctly. (See page 8.)

Make the correct size setting for the

speaker. (See page 10.)

Increase the speaker level setting to get

the balance right with the other speak-

ers. (See page 11.)

Set the center speaker size to OFF. (See

page 10.)

Additional Information

En

17

English

Español

Deutsch

Français

Italiano

Nederlands

04

Section

Audio/DSP

Symptom Cause Remedy

Speakers are not available to be

adjusted.

Time alignment is not available.

The subwoofer is not available to

switch its phase.

Bass content is not heard.

Occasionally no sounds are outputted

when Dolby Pro Logic is switched on.

Occasionally no sounds are heard over

speakers other than the center one.

Switching dynamic range control on

has no effects.

Their size settings is at OFF.

Listening position is not set

correctly.

Their size settings is at OFF.

The subwoofer is set to OFF.

The subwoofer is set to OFF

and yet other speakers are set

to OFF or SMALL in size.

The center speaker setting is at

SMALL or LARGE whereas

no center speaker is installed.

Dolby Pro Logic is switched on.

The currently reproduced

sound is not Dolby Digital

coded.

Make the correct size settings. (See page

10.)

Set listening position correctly. (See

page 7.)

Make the correct size settings. (See page

10.)

Set the subwoofer to ON. (See page 10.)

Make the correct settings. (If no sub-

woofer is installed, the front or rear

speaker needs to be set to LARGE.) (See

page 10.)

Change the center speaker size setting to

OFF. (If the audio source is mono and

Dolby Pro Logic is switched on, sound is

heard over the center speaker only.) (See

page 10.)

Set Dolby Pro Logic to OFF. (If the audio

source is mono and Dolby Pro Logic is

switched on, sound is heard over the

center speaker only.) (See page 9.)

The feature is only effective on Dolby

Digital sounds. (See page 9.)

DVD player setting

Symptom Cause Remedy

No sounds come from the DVD player

only.

The optical cable has become

detached.

The DVD player is not properly

set for output.

Connect the cable correctly.

Make the correct output setting. (See the

manual for the DVD player.)

Additional Information

Te r m s

Dolby Digital

Dolby Digital provides discrete multichannel

(up to a maximum of 5.1) audio. This is the same

audio system as is installed in movie theaters.

To enjoy Dolby Digital sound you need to con-

nect this unit's optical digital input to the digital

output on a DVD player with Dolby Digital

decoding capability.

1

Dolby Surround Pro Logic

When you play a 2-channel audio disc marked

Dolby Surround Pro Logic using an AV amplifier

equipped for Dolby Pro Logic, the audio is con-

verted into 4-channel audio.

Dolby Pro Logic gives enhanced spatial and

directional effects, creating theater-like sense of

presence and ambience.

5

DTS for Digital Theater Surround

DTS is a surround system delivering multi-chan-

nel audio from up to 6 independent sources. To

hear DTS discs, you need to connect the digital

output on DTS-capable DVD players and other

units to this unit's digital input.

Dynamic Range Control

Dolby Digital has a function for compressing

the difference between the loudest and softest

sounds: Dynamic Range Control. This control

ensures sounds with an increased dynamic

range are heard clearly even at low volume lev-

els.

Linear PCM (LPCM) /Pulse Code

Modulation

This is a recording technology used on music

CDs. Some DVD-Video discs also contain PCM

sound tracks. While music CDs are recorded at

44.1 kHz/16 bits, DVD-Video discs’ sound tracks

are recorded at 48 kHz/16 bits to 96 kHz/24 bits,

thereby offering better quality audio than music

CDs.

Optical Digital Input

By receiving optical digital input audio signals

in a digital signal format, the chance is mini-

mized that the sonic quality deteriorates in the

course of transmission. An optical digital input

is an input designed to receive digital signals

optically. (To take advantage of the digital input,

output units such as DVD players must have

optical outputs.)

En

18

04

Section

Additional Information

En

19

Specifications

General

Power source ...................... 14.4 V DC

(10.8 – 15.1 V allowable)

Grounding system .............. Negative type

Max. current consumption:

Backup current ........... 10 A

Dimensions (W × H × D) .... 237 × 29 × 171 mm

Weight ................................. 1.05 kg

Amplifier

Maximum power output ..... 50 W × 5

Continuous power output

............................................. 27 W × 5

(DIN45324, +B=14.4 V)

Load impedance ................. 4 Ω

Preout maximum output level

............................................. 5.0 V

Decoder ............................... Linear PCM/Dolby

Digital/Dolby Pro

Logic/DTS

Subwoofer output:

Crossover frequency

..................................... 63/80/100/125/160/200 Hz

Level ............................ ±10 dB

Speaker setting:

Time alignment ........... 0 – 500 cm (2.5 cm)

Level ............................ ±10 dB

Equalizer:

Band .................... 3 band

Frequency ............ 100/125/160/200/250/315/

400/500/630/800/1k/1.25k/

1.6k/2k/2.5k/3.15k/4k/5k/

6.3k/8k Hz

Gain ..................... ±12 dB

Crossover frequency

............................. 63/80/100/125/160/200 Hz

Note

• Specifications and the design are subject to

possible modification without notice due to

improvements.

English

Español

Deutsch

Français

Italiano

Nederlands

04

Section

Page is loading ...

Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to oper-
ate your model properly. After you have finished reading the instructions, put them
away in a safe place for future reference.
Contents
It
2
Prima di iniziare
Informazioni su questo apparecchio 3
• Compatibilità Dolby Digital/DTS
(unendo questo apparecchio ad un
lettore DVD Pioneer come il DVH-
P7000R) 3
Informazioni su questo manuale 3
Precauzioni 3
In caso di problemi 3
Ripristinare il microprocessore 4
Impostazioni di uscita del lettore DVD 4
Elenco dei comandi 5
• Frontalino 5
Regolazioni audio
Introduzione alle regolazioni audio 6
• Uso del menu audio 6
• Uso del menu dettagli audio 6
Uso del controllo di campo sonoro 7
Uso del selettore di posizione 7
Uso della regolazione del bilanciamento 8
Regolazione dei livelli fonte 8
Uso del controllo di gamma dinamica 9
Uso del modo mono doppio 9
Uso del controllo diretto 9
Uso del Dolby Pro Logic 9
Impostazione dei diffusori 10
• Correzione della fase del subwoofer 10
Selezione di una frequenza di taglio 11
Regolazione del livello di uscita dei diffusori
11
Regolazione dei livelli di uscita del diffusore
mediante un tono di prova 12
Regolazione dell’allineamento temporale
13
Uso dell’equalizzatore 13
• Richiamo delle curve dell’equalizzatore
13
• Regolazione dell’equalizzatore para-
metrico a 3 bande 14
Impostazioni iniziali
Correzione del suono distorto 15
Informazioni supplementari
Ricerca guasti 16
• Communs 16
• Audio/DSP 17
• Impostazione del lettore DVD 17
Termini 18
Dati tecnici 19
Grazie di aver acquistato questo prodotto Pioneer.
Leggere attentamente queste istruzioni operative, in modo da imparare come
azionare correttamente il modello. Dopo aver terminato la lettura delle istruzioni,
metterle da parte in un posto sicuro, per consultazione futura.
Sommario
00
Sezione

Page is loading ...

Pioneer DEQ-P7000 User manual

Pioneer DEQ-P7000 User manual

in other languages

Related papers

Other documents