ICP DAS USA MDC-714 Quick Start

Brand: ICP DAS USA

Model: MDC-714

Type: Quick Start

This manual is also suitable for

MDC-711

Quick Start for MDC‐700 Series



November 2014, Version 1.00



ThisQuickStartintendstoprovideinformationneededtogetstartedwithMDC‐711andMDC‐714.

Pleasealsoconsulttheusermanualfordetailedinformationonthesetupanduseofthemodule.

What ’sIntheBox?

Inadditiontothisguide,thepackageincludesthefollowingitems:

Quick Start for MDC-700 Series



Module SoftwareUtilityCD

RS‐232Cable

(CA‐0910)

ScrewDriver

TechnicalSupport

UserManual

CD:\NAPDOS\Modbus\MDC_700\Document\

http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/mdc_700/document/

Firmware

CD:\NAPDOS\Modbus\MDC_700\Firmware\

http://ftp.icpdas.com/pub/cd/8000cd/napdos/modbus/mdc_700/firmware/

ICPDASWebsite

http://www.icpdas.com

1ConnectingtoPC,NetworkandPower

ThemoduleisequippedwithastandardEthernetport(RJ‐45)forconnectingtoanEthernet

Hub/SwitchandPC.Moreover,youcanalsoconnectthePCdirectlywithanEthernetcable.

Powersupply(+10~+30V

)

Hub/Switch

Quick Start for MDC-700 Series



2 

efore,

4byusing

b‐basedinterface,youmustknowtheIPaddresstheMDC‐711/MDC‐714isusing.The

2.168.255.1bydefault.

STEP1

STEP2

/MDC‐714isusingthedefaultIPaddressof192.168.255.1,youmustchose

IPaddressforthecomputerintherangeof192.168.255.2–192.168.255.253thatisnot

essonyourcomputerdependuponthetype

chitectureandoperatingsystemyouareusing.UsethecomputerHelpandSupport

functionalitytosearchfor“IPAddressing”.



AssigninganIPaddresstoMDC‐711/MDC‐714

TheMDC‐711/MDC‐714isanEthernetdevice,whichcomeswithadefaultIPaddress;ther

youmustfirstassignanewIPaddresstothemodule.ToaccesstheMDC‐711/MDC‐71

MDC‐711/MDC‐714usesthefactorydefaultIPaddressof19



PoweronthecomputerandtheMDC‐711/MDC‐714.

SettheIPconfigurationonyourcomputer.

IftheMDC‐711

alreadyinuse.



NOTE:DetailsonhowtochangetheIPaddr



Quick Start for MDC-700 Series

STEP3Openawebbrowserandgotothewebsiteathttp://192.168.255.1,where192.168.255.1is

thedefaultIPaddressofyourMDC‐711/MDC‐714.



STEP4OpentheIPaddressconfigurationinterfacebyclickingtheEthernetConfiguration.



SETP5ChooseanewIPaddressforyourMDC‐711/MDC‐714.Makesurethattheaddressyoupickis

notcurrentlyinusebyanotherdeviceonthenetwork.



NOTE:TheMDC‐711/MDC‐714canberesettofactorydefaultsbyshortingtheRESETpinto

GNDpinfor3seconds.TheLEDdisplaywillshow“RESET ” asbelowandremovetheIP

addresssetpreviouslyfortheMDC‐711/MDC‐714.



3EnablingAdobeFlashPlayerinYourBrowser

YourbrowsermustsupportAdobeFlashPlayerandhaveitenabledinordertousethebuilt‐inweb

server.Ifyoudonothaveitinstalled,pleasegotothefollowingwebsiteandinstallit.



TheAdobeFlashPlayerDownloadCenter：

http://get.adobe.com/flashplayer/

4GototheWebSitetoCheckoutFunctions

Quick Start for MDC-700 Series

Gotothewebinterfaceathttp://xxx.xxx.xxx.xxx,wherexxx.xxx.xxx.xxxistheIPaddressofyour

MDC‐711/MDC‐714.AnystandardbrowsercanbeusedtointerfacetheMDC‐711/MDC‐714,such

asMozillaFirefox,InternetExplorerorGoogleChrome.



NOTE:Ifyouhaven’tchangedthedefaultIPaddressofthemodule,pleasereferto“2.AssignanIP

addressonMDC‐711/MDC‐714”toconfigureit.



ICP DAS USA MDC-714 Quick Start

Brand: ICP DAS USA

Model: MDC-714

Type: Quick Start

This manual is also suitable for

MDC-711

Download PDF

report

ICP DAS USA MDC-714 Quick Start

This manual is also suitable for

ICP DAS USA MDC-714 Quick Start

Related papers

Other documents