Classic Flame 75577 Operating instructions

Brand: Classic Flame

Model: 75577

Category: AV equipment stands

Type: Operating instructions

Classic Flame 75577 is an electric fireplace mantel with a realistic flame effect that can be used to add warmth and ambiance to any room. It features a sturdy construction with a weight capacity of up to 135 pounds, making it suitable for supporting TVs up to 62 inches. The mantel also comes with a convenient glass shelf for displaying décor or other items. Additionally, it has a built-in insert support bar for easy installation of an electric fireplace insert, allowing you to enjoy the warmth and ambiance of a real fire without the hassle of wood or gas.

Français p. 15

ELECTRIC FIREPLACE MANTEL

26MM9405

INSTRUCTION MANUAL

Requires-Electric Fireplace Requires-Electric Fireplace

Insert with HeaterInsert with Heater

www.twinstarhome.com

In English call: 866-661-1218

In French call: 866-374-9203

In Spanish call: 866-661-1218

ATTENTION

For Customer Service:

Twin-Star International, Inc.

Delray Beach, FL 33445

Made in China

Printed in China

Español p. 8

MAXIMUM LOAD 30 lb. (13.6kg)

CAUTION: This unit is intended for use only with the products and maximum weights

indicated. Use with other products or products heavier than the maximum weights

indicated may result in instability causing possible injury

Note: Flat Panel TVs with base support should be placed squarely in the center of the

stand with no overhang on any side.

FIT UP TO 62” PLASMA/LCD TELEVISIONS

MAXIMUM LOAD 135 lb. (61.22 kg)

PACKAGE CONTENTS

Part Description Quantity

A Hearth/Base 1

B Center Left Side Panel 1

C Center Right Side Panel 1

D Center Front Panel 1

E Left Side Panel 1

F Right Side Panel 1

G Glass Top 1

H Glass Shelf 2

I Side Back Panel 1

J Insert Support Bar 1

K Mantel/Top 1

L Glass Door 2

HARDWARE CONTENTS

Part

Description

Bolt

Washer

20+1 extra

Quantity

Picture

(Shown to size)

Wood Dowel

Suction Cup

Door Touch Clip

Pivot Hinge

Magnetic Spring Catch

Shelf Pin

Metal Support Post

Screw

Tipping Restraint

Hardware

Touch-up Pen

SAFETY INFORMATION

WARNING

• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.

Make sure you do not discard the hardware.

CAUTION

• Use care in assembling your new ﬁreplace. Take your time and use the hardware

provided and a quality Phillips head screwdriver. Never overtighten bolts.

• Do not sit on any part of the mantel.

• All panels are labeled left and right as viewed from the front of unit.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and diagram above. If any part is missing or damaged, do not attempt to

assemble, install or operate the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 Minutes

Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife

ASSEMBLY INSTRUCTIONS

Fig. 1

Hardware Used

Screw x 2

Wood Dowel

x 4

1. Locate the Center Left Side Panel (B), Center Right

Side Panel (C), Center Front Panel (D), and set out

face down on a scratch-free surface.

Insert one Wood Dowel (CC) into each of the

pre-drilled holes.

Push the Center Left Side Panel and Center Right

Side Panel snug to the Center Front Panel. Make

sure the Wood Dowels are seated in the pre-drilled

holes.

Connect the Center Left Side Panel (B), Center

Right Side Panel (C) and Center Front Panel (D)

with Connection Plate, tighten Screws (JJ) through

the pre-drilled holes.

Fig. 2

2. Locate Hearth/Base (A) and set out ﬁ nished side up

on the ﬂ oor.

Insert one Wood Dowel (CC) into each of the

pre-drilled holes.

Attach the Completed assembly from step 1 to the

Hearth/Base (A). Make sure that dowels are seated

into the pre-drilled holes in the Hearth/Base. Using

Bolts (AA) and Washers (BB) attach panels through

pre-drilled holes in the mounting blocks.

HAND TIGHTEN ONLY.

Insert one Wood Dowel (CC) into each of pre-drilled

holes. Push the Right Side Panel (F) and Left Side

Panel (E) snug to completed assembly. Using Bolts

(AA) and Washers (BB) through the pre-drilled holes

in the mounting blocks.

HAND TIGHTEN ONLY.

3. Insert one Wood Dowel (CC) into each of the

pre-drilled holes on the top edges of the Assembly

from step 2. Then locate Mantel/Top (K) and lay

ﬁ nished side up on top of completed assembly. From

the inside, attach Mantel/Top (K) using Bolts (AA)

and Washers (BB) through the pre-drilled holes in

the mounting blocks.

HAND TIGHTEN ONLY.

Hardware Used

Bolt

x 8

x 10

Washer

x 8

x 10

Wood Dowel

x 8

Fig. 3

Fig. 4

Hardware Used

Screw x 20

4. Attach Side Back Panels (I) to the back of the

completed assembly from step 3. Use a Phillips

Head Screw Driver, tighten Wood Screws (JJ)

through the pre-drilled holes in the Side Back Panels

(I).

Fig. 5

Fig. 6

Fig. 7

5. Attach the Magnetic Spring Catch (GG) on the

bottom of Top Panel, tighten screws (KK) through

holes to the block as shown in diagram.

Place the Door Touch Clip (DD) to the glass door.

Insert the Pivot Hinge (FF) into the plastic mat as

shown in diagram. Then push the Glass Doors (L)

snug to the Pivot Hinges (FF), use a Phillips Head

Screwdriver to tighten the pivot hinge against the

glass.

WARNING

Do not over tighten catch screws.

Damage to the Glass could occur!

Hardware Used

Shelf Pin

Door Touch Clip

Suction Cup

Pivot Hinge

Metal Support

Post

Magnetic Spring

Catch

screw

x 8

x 2

x 6

x 4

x 6

x 2

x 8

6. Choose desired height of Glass Shelf (H) and place

the four Shelf Pin (HH) into same height shelf holes

inside side panels. Insert Glass Shelf (H), allow

Glass Shelf (H) to rest on the Shelf Pin (HH).

7. Attach the Metal Support Post (II) and screw

clockwise into inset threads on the top of the mantel.

Insert the Suction Cups (EE) into the Support Posts,

with the help of another adult carefully lower the

Glass Top (G) onto the Support Posts.

Fig. 8

8. PLEASE READ ALL “ELECTRIC FIREPLACE

INSERT” INSTRUCTIONS PRIOR TO

INSTALLING ELECTRIC INSERT IN YOUR

COMPLETED FIREPLACE MANTEL. INSTALL

THE INSERT IN YOUR FIREPLACE CLOSE TO

ITS FINAL POSITION.

Lift insert carefully into the back of the unit and

center in the insert opening. Do not drag insert

across hearth/base as it may scratch the unit.

Connect the Insert Support Bar (J) to the inside left

and right panels, using the bolt (AA) and washer

(BB) through pre-drilled holes.

MOVE YOUR COMPLETED UNIT ONLY SHORT

DISTANCES. MOVE COMPLETED UNIT WITH

GREAT CARE. IT TAKES TWO PEOPLE TO

MOVE COMPLETED UNIT INTO ITS FINAL

POSITION.

Hardware Used

Bolt x 2

Washer x 2

Completed

Unit

Electric

Fireplace Insert

Install

Insert

From

Back

AA BB

Fig. 9

9. We have included two Tipping Restraints for this

unit. You must install this hardware to prevent

accidents or injuries. When properly installed, this

restraint can provide protection against unexpected

tipping of the Unit due to small tremors, bumps or

climbing. We strongly recommend mounting this

hardware to a wall stud and your Unit.

Warning: You must install the Tipping Restraint

Hardware to help prevent accidents or damage to

the unit.

Hardware Used

Tipping Restraint

Hardware

x 2

Cabinet

Wall Stud

Wall

Classic Flame 75577 Operating instructions

Brand: Classic Flame

Model: 75577

Category: AV equipment stands

Type: Operating instructions

Download PDF

report

Classic Flame 75577 Operating instructions

Classic Flame 75577 Operating instructions

Related papers

Other documents