2. Office
  3. Mail supplies
  4. Packaging materials
  5. Storage chests & cabinets & trunks
  6. Classic Flame
  7. 81110

Classic Flame 81110 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Classic Flame 81110 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service:
www.tsicustomerservice.com
in English Call: 866-661-1218
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU
APPELEZ LE SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle:
www.tsicustomerservice.com
pour le service en français: 866-661-1219
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS, ENVÍE UN
MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER ESTE
PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente:
www.tsicustomerservice.com
Línea para llamadas en español: 866-661-1219
1
ELECTRIC FIREPLACE MANTEL
WITH THERMOELECTRIC COOLER
26TF8299
ASSEMBLY INSTRUCTION
Español p. 9
Français p. 17
Requires-Electric Fireplace
Insert with Heater
ATTENTION
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
www.tsicustomerservice.com
English Call: 866-661-1218
Spanish /French Call: 866-661-1219
For Customer Service:
2
PACKAGE CONTENTS
G
L
M
P
N
I
K
J
H
D
B
A
O
E
C
F
Part Description Quantity
A Hearth/Base 1
B Center Left Side Panel 1
C Center Right Side Panel 1
D Center Shelf 1
E Left Side Panel 1
F Right Side Panel 1
G Media Top 1
H Wood Shelf 1
I Left Back Panel 1
J Center Back Panel 1
K Right Back Panel 1
L Left Front Door 1
M Right Front Door 1
N Positioning Panel 1
O Right Inner Panel 1
P Insert Support Bar 1
3
HARDWARE CONTENTS
Part
Description
Bolt
Washer
Screw
Screw
Screw
Door Clip
Handle (with bolt)
Tipping Restraint
Hardware
Shelf Pin
24+1 extra
24+1 extra
15
12
11
1
2
2
4
Quantity
Picture
(Shown to size)
BB
CC
DD
EE
FF
GG
HH
II
AA
SAFETY INFORMATION
WARNING
•Beforeassembly,carefullyusescissorsorutilityknifetocutandunwrapallparts.
Make sure you do not discard the hardware.
CAUTION
•Usecareinassemblingyournewfireplace.Takeyourtimeandusethehardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
•Donotsitonanypartofthemantel.
•Allpanelsarelabeledleftandrightasviewedfromthefrontofunit.
Screw
Wood Dowel
Touch-up Pen
2
20+1 extra
1
JJ
KK
ZZ
4
ASSEMBLY INSTRUCTIONS
PREPARATION
Beforebeginningassemblyofproduct,makesureallpartsarepresent.Comparepartswith
packagecontentslistanddiagramabove.Ifanypartismissingordamaged,donotattemptto
assemble,installoroperatetheproduct.Contactcustomerserviceforreplacementparts.
EstimatedAssemblyTime:60Minutes
ToolsRequiredforAssembly(notincluded):Phillipsheadscrewdriver,scissorsandutilityknife
Fig. 1
1. Locate the Center Left Side Panel (B), Center
Right Side Panel (C), Center Shelf (D), and set
out face down on a scratch-free surface.
Insert one Wood Dowel (KK) into each of the
pre-drilled holes.
Push the Center Left Side Panel and Center Right
SidePanelsnugtotheCenterShelf.UsingBolts
(AA) and Washers (BB) attach these panels through
pre-drilledholesinthemountingblocks.
HAND TIGHTEN ONLY.
F
E
BB
KK
AA
C
B
D
Fig. 2
2.LocateHearth/Base(A)andsetoutfinishedsideup
ontheoor.
Insert one Wood Dowel (KK) into each of the
pre-drilled holes.
AttachtheCompletedCenterFrontassemblyfrom
step1totheHearth/Base(A).UsingBolts(AA)and
Washers (BB) attach panels through pre-drilled
holesinthemountingblocks.
HAND TIGHTEN ONLY.
Locate Left Side Panel (E) and Right Side Panel (F),
Then use Bolts (AA) and Washers (BB) through the
pre-drilledholesinthemountingblocks.Attachthe
Side Panels to Hearth / Base (A).
HAND TIGHTEN ONLY.
Hardware Used
Hardware Used
BB
KK
KK
BB
AA
AA
Bolt
Bolt
x 4
x 10
Washer
Wood Dowel
Wood Dowel
Washer
x 4
x 4
x 8
x 10
BB
A
AA
KK
5
Fig. 4
I
J
DD
3. Insert one Wood Dowel (KK) into each of the
pre-drilledholesonthetopedgesoftheAssembly
fromstep2.ThenlocateMediaTop(G)andlay
finishedsideupontopofcompletedassemblyFrom
the inside, attach Media Top (G) using Bolts (AA)
and Washers (BB) through the pre-drilled holes in
themountingblocks.
HAND TIGHTEN ONLY.
UsingPhillipsheadscrewdrivertightenallBolts
alternatingtopandbottom,leftandright.
4. Locate Center Back Panel (J), using a Phillips Head
screw driver,tighten screws (DD) through the
pre-drilled holes in the Center Back Panel to the
completedassembly.
Locate Left Back Panel (I), using a Phillips Head
screw driver,tighten screws (DD) through the
pre-drilled holes in the Left Back Panel to the
completedassembly.
AA
KK
BB
Fig. 3
G
Hardware Used
Hardware Used
BB
AA
DD
Bolt
Screw
x 8
x 15
Washer x 8
Fig. 5
EE
M
HH
HH
Handle
(with bolt)
x 2
Hardware Used
EE
Screw x 12
5. Connect the Right Front Door (M) to the Right Side
Panel (F) with the hinge pre-installed on the door,
then use a Phillips head screwdriver to tighten the
Screws (EE) through the pre-drilled holes.
Attach the Handle (HH) to the Front Door (M), use
the bolts attached through the pre-drilled holes in
the door. Then use a Phillips Head Screwdriver to
tighten the bolts.
Repeat the other side.
Therearelevelerslocatedunderthemantelwhich
the height can be increased by twisting
counter-clockwise.
KK
Wood Dowel x 8
6
Fig. 7
7. PLEASE READ ALL “WINE COOLER” AND
“ELECTRIC FIREPLACE INSERT”
INSTRUCTIONSPRIORTOINSTALLING
INYOURCOMPLETEDFIREPLACEMANTEL.
INSTALLTHEINSERTINYOURFIREPLACE
CLOSE TO ITS FINAL POSITION.
Insert the wine cooler feet into the holes of the
Positioning Panel (N). Push the panel forward until
thecoolermakescontactwiththefrontframeofthe
mantel.
N
Fig.6
CC
H
Fig. 8
FF
K
Hardware Used
FF
Screw x 4
8. Locate Right Back Panel (K), using a Phillips Head
screw driver to tighten screws (FF) through the
pre-drilled holes.
6.ChoosedesiredheightofShelf(H)andplacethe
fourShelfPin(CC)intosameheightshelfholes
inside side panels. Insert Wood Shelf (H), allow
Wood Shelf (H) to rest on the Shelf Pin (CC)
Hardware Used
CC
Shelf Pin x 4
7
Fig. 10
10. Open the Right Front Door (M) and cooler door,
connect the Right Front Door (M) to the cooler door
with Screws (JJ) and Door Clip (GG), Usea
Phillips Head Screw Driver to tighten Screws (JJ)
through the pre-drilled holes in the Door Clip (GG).
Close door and adjust the wine cooler forwards or
backwardstoinsureasmoothoperationofthe
door with a tight seal.
Note: Installing the clip with the door open at
a 45 degree angle will help insure a smooth
operation through the full motion of the door.
JJ
Screw x 2
JJ
GG
Hardware Used
Fig. 9
Fig. 11
FF
O
FF
Hardware Used
FF
Screw x 3
11. Lacate the Positioning Panel (N), using a Phillips
Head Screw Driver to tighten Screws (FF) through
the pre-drilled holes.
Hardware Used
FF
Screw x 4
9. Locate Right Inner Panel (O), using a Phillips Head
screw driver to tighten screws (FF) through the
pre-drilled holes.
N
8
Fig. 13
II
II
13. We have included two Tipping Restraints for this
unit.Youmustinstallthishardwaretoprevent
accidents or injuries. When properly installed,
this restraint can provide protection against
unexpectedtippingoftheUnitduetosmall
tremors,bumpsorclimbing.Westrongly
recommendmountingthishardwaretoawall
studandyourUnit.
Warning:YoumustinstalltheTippingRestraint
Hardwaretohelppreventaccidentsordamage
to the unit.
Hardware Used
Tipping Restraint
Hardware
x 2
Cabinet
Wall Stud
Wall
Fig. 12
Completed
Unit
Electric
Fireplace Insert
Install
Insert
From
Back
AA
BB
P
Hardware Used
BB
AA
Bolt x 2
Washer x 2
12. Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
acrosshearth/baseasitmayscratchtheunit.
Connect the Insert Support Bar (P) to the inside left
and right panels, using the bolt (AA) and washer
(BB) through pre-drilled holes.
MOVEYOURCOMPLETEDUNITONLYSHORT
DISTANCES.MOVECOMPLETEDUNITWITH
GREAT CARE. IT TAKES TWO PEOPLE TO
MOVECOMPLETEDUNITINTOITSFINAL
POSITION.
9
CHIMENEA ELÉCTRICA CON
REFRIGERADOR TERMOELÉCTRICO
26TF8299
INSTRUCCIÓN DE MONTAJE
English p. 1
Français p. 17
Necesitará, Además, El
Hogar Eléctrico Con Calentador
ATENCIÓN
Twin-Star International, Inc.
Delray Beach, FL 33445
Fabricado en China
ImpresoenChina
www.tsicustomerservice.com
Inglés llamadas:: 866-661-1218
Español /Français llamadas: 866-661-1219
Servicio de atención al cliente:
/