Owens Corning RLP Installation guide

RLP
Owens Corning
Brand
Owens Corning
Model
RLP
Type
Installation guide

Owens Corning RLP is a pre-assembled, easy-to-install, fire-rated recessed light cover designed to provide code-compliant clearance between thermal insulation and non-IC rated recessed light fixtures in attics. It features Owens Corning Advantex Fiber Technology for added strength, fire resistance, mold resistance, and reduced air pollution. The RLP also has ventilation holes to allow heat build-up from lights to escape and can support attic R-Values R 60+ with a maximum insulation height of 24 inches.

Owens Corning RLP is a pre-assembled, easy-to-install, fire-rated recessed light cover designed to provide code-compliant clearance between thermal insulation and non-IC rated recessed light fixtures in attics. It features Owens Corning Advantex Fiber Technology for added strength, fire resistance, mold resistance, and reduced air pollution. The RLP also has ventilation holes to allow heat build-up from lights to escape and can support attic R-Values R 60+ with a maximum insulation height of 24 inches.

SmartCap
™
Attic Recessed Light Cover
CHOOSE THE SMART CHOICE FOR ATTIC NON-IC RATED LIGHT FIXTURES
Introduction
Make your next attic insulation project that much easier by adding a SmartCap
™
Attic Recessed
Light Cover to your list of hard working insulation accessories. SmartCap
™
Attic Recessed Light
Cover is a pre-assembled, easy to install,  re rated recessed light cover that simply unfolds into a
perfect cap over non-IC rated light  xtures in the attic.
Unlike site fabricated light covers that require excessive time, labor, and cost to build, SmartCap
™
Attic Recessed Light Cover is an easy solution to a complex problem. And, it offers you these
strong performance, building and safety code standards:
• Owens Corning Advantex
®
Fiber Technology is at the heart of SmartCap
™
Attic Recessed
Light Cover, providing:
- Added strength
- Fire resistance
- Mold resistance
- E-Glass and boron free minimizing air pollution
• Provides code speci ed clearance between thermal insulation and non-IC rated recessed light
xtures in attics.
• Code Compliant
• Class A Fire Retardant
• Mold Resistant
• Ventilation air holes to allow heat build up from lights to escape
• Easy to cut for custom  t
• Supports Attic R-Values R 60+
• Foil Facing
Practical Applications
• Folds-out into position between attic joists running parallel to joists to easily cover both the
light  xture and its accompanying electrical box.
• Designed for non-IC recessed light  xtures with a nominal diameter of 7" (178 mm) or less. It
should not be used for recessed light  xtures with nominal diameters greater than 7" (178 mm).
• Allows attic insulations to achieve R values in excess of R-60 with maximum insulation heights
as high as 24".
Applicable Standards
The surface burning characteristics of SmartCap
™
Attic Recessed Light Cover were tested in
accordance with ASTM E 84.
Both the SmartCap
™
Attic Recessed Light Cover facing and  berglass interior veil were tested for
resistance to fungi (mold and mildew) per ASTM C1338 and ASTM D 3273.
10011610-A.indd 110011610-A.indd 1 3/16/2010 5:19:59 PM3/16/2010 5:19:59 PM
SmartCap
™
Attic Recessed Light Cover
Easy Installation
Step 1: Center SmartCap
™
Attic Recessed Light Cover over
the recessed light  xture.
Step 2: Cutting may not be required when lights are centered
between joists. If required, SmartCap
™
Attic Recessed
Light Cover cuts easily using scissors or a utility knife to
t evenly over any obstructions such as light bracing,
electrical wiring, or joists.
Step 3: Secure the base of the SmartCap
™
Attic Recessed Light
Cover to the drywall ceiling with foil or duct tape.
Step 4: Install insulation.
Technical Dat a
Open Width Open Length Open Height
14" 351 mm 23" 508 mm 26" 660 mm
Performance
Attribute Test Method Nominal Value/Results
Fungi Resistance ASTM C 1338
ASTM D 3273
Pass – No mold growth
Not Susceptible to Mold
Growth
Flame Spread/
Smoke Developed
ASTM E 84 15 Flame Spread
30 Smoke Development
Heat Dissipation
From Luminaries
UL 1598 Stabilized temperature
within SmartCap
™
enclosure less than
maximum value of 194°F.
1
2
3
4
OWENS CORNING INSULATING SYSTEMS, LLC
ONE OWENS CORNING PARKWAY
TOLEDO, OHIO, USA 43659
1-800-GET-PINK
®
ww w.owenscorning.com
Pub. No. 10011610-A. Printed in U.S.A. March 2010. THE PINK PANTHER
™
& ©1964–2010 Metro-Goldwyn-Mayer Studios Inc. All Rights
Reserved. The color PINK is a registered trademark of Owens Corning.
©2010 Owens Corning.
10011610-A.indd 210011610-A.indd 2 3/16/2010 5:20:00 PM3/16/2010 5:20:00 PM
  • Page 1 1
  • Page 2 2

Owens Corning RLP Installation guide

RLP
Owens Corning
Brand
Owens Corning
Model
RLP
Type
Installation guide

Owens Corning RLP is a pre-assembled, easy-to-install, fire-rated recessed light cover designed to provide code-compliant clearance between thermal insulation and non-IC rated recessed light fixtures in attics. It features Owens Corning Advantex Fiber Technology for added strength, fire resistance, mold resistance, and reduced air pollution. The RLP also has ventilation holes to allow heat build-up from lights to escape and can support attic R-Values R 60+ with a maximum insulation height of 24 inches.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents