Danfoss SonoSelect and SonoSafe User guide

Brand: Danfoss

Model: SonoSelect and SonoSafe

Category: Measuring, testing & control

Type: User guide

Danfoss SonoSelect and SonoSafe are energy meters designed to measure and display energy consumption in heating and cooling systems. They feature a compact and lightweight design, making them easy to install in various applications. With their advanced technology, these meters provide accurate and reliable measurements, helping users monitor and optimize their energy usage. Additionally, they offer various communication options, enabling integration with building management systems for remote monitoring and data analysis.

103/2016 © Danfoss VUIGB402

Installation & User Guide

SonoSelect and SonoSafe

energy meters

2 | © Danfoss | Energy Meters | 2016.03 VUIGB402

Installation & User Guide SonoSelect and SonoSafe

Danfoss A/S

K-6430 Nordborg

enmark

VR nr.: 20 16 57 15

elephone: +45 7488 2222

ax: +45 7449 0949

EC/EU DECLARATION OF CONFORMITY

Danfoss A/S

Danfoss Energy Metering

declares under our sole responsibility that the

Product(s):

SonoSafe 10 and SonoSelect 10 Energy Meters

covered by this declaration is in conformity with the following directive(s), standard(s) or other

normative document(s), provided that the product is used in accordance with our instructions.

• MID Directive 2004/22/EC Measurement Instrument Directive (Until 2016.04.19)

• MID Directive 2014/32/EU Measurement Instrument Directive (From 2016.04.20)

Module B +D

o EN1434: 2007 Heat meters

o EN1434: 2015/TC176-

WG2_N480

•

EMC Directive 2004/108/EC Electromagnetic compatibility (Until 2016.04.19)

• EMC Directive 2014/30/EU Electromagnetic compatibility (From 2016.04.20)

o EN 61000-6-1 Electromagnetic compatibility (EMC) Immunity for

residential, commercial and light-industrial environme

nts

(IEC 61000-6-1)

o EN 61000-6-4 Electromagnetic compatibility (EMC) Emission standard

for industrial environments (IEC 61000-6-4)

• RoHS Directive 2011/65/EU Restriction of Hazardous substances

• WEEE Directive 2002/96/EC Waste Electrical and Electronic Equipment

e products are provided with the following marking of conformity

e rst year of production is 2016

Date Issued by Date Approved by

2016.03.09

Søren Nielsen

R&D Director, Danfoss Energy Metering

2016.03.10

Bjarne Halkjær

Strategy & portfolio Director

Danfoss only vouches for the correctness of the English version of this declaration. In the event of the declaration being translated into any other

language, the translator concerned shall be liable for the correctness of the translation

ID No: 014R2903 Revision No: 03 Page

1 of 1

VUIGB402 © Danfoss | Energy Meters | 2016.03 | 3

Installation & User Guide SonoSelect and SonoSafe

Contents

1. Inside the box ........................................................................... 4

2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Preparation........................................................................... 4

2.2 Identification of installation: Supply/Return pipe installation ........................... 5

2.3 Flow sensor installation............................................................... 5

2.4 Mounting orientation, calculator ...................................................... 5

2.5 Mounting of O-ring and temperature sensor ..........................................6

2.6 Communication (Expansion modules)................................................. 7

2.7 Installation of module/cable .......................................................... 8

2.8 Battery ...............................................................................9

3. Commissioning ......................................................................... 10

3.1 Bleeding ........................................................................... 10

3.2 Supply/return configuration .........................................................10

3.3 Meter sealing....................................................................... 10

3.4 IP class ............................................................................. 10

4. Function overview ...................................................................... 11

4.1 Menu structure ..................................................................... 11

4.2 Display explanation..................................................................12

4.3 Alarms ..............................................................................12

5. Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6. Disposal................................................................................ 13

4 | © Danfoss | Energy Meters | 2016.03 VUIGB402

Installation & User Guide SonoSelect and SonoSafe

1. Inside the box

Description of components included in the box

107/2015 © Danfoss VDIGH102

Installation Guide

SonoSelect and SonoSafe

energy meters

1 x

Energy meter

2 x

Gaskets

1 x

Temperature sensor

O-ring and mounting pin

4 x

Wired seals

1 x

Installation

& User Guide

2. Installation

2.1 Preparation

SonoSelect incorporates a tamper monitor-

ing function. If the calculator is opened the

meter will set alarm E13 in display.

Don’t open unless for adding communica-

tion module, replacing battery or installing

cables.

Reset requires Bluetooth dongle 014U1963

and SonoApp service tool.

SonoSelect is delivered with the option

of reconfiguring supply/return using the

Bluetooth dongle 014U1963 and SonoApp

service tool.

Note!

• Product is approved for ambient temperature between 5-55 °C, but to ensure optimal conditions for battery it

is recommended to install Calculator at max. 45 °C.

• Avoid installation stress from pipes and fittings.

• Flush the system.

VUIGB402 © Danfoss | Energy Meters | 2016.03 | 5

Installation & User Guide SonoSelect and SonoSafe

2.2 Identification of installation: Supply/Return pipe installation

Supply installation Return installation

2.3 Flow sensor installation

Pipe position: No limitations but avoid positions

where air can be collected.

Rotation in pipe axis: Flow sensor should be angled

in 45 to 315° to avoid air collection in flow sensor.

2.4 Mounting orientation, calculator

4 x 90°

Click!

1a.

1b.

6 | © Danfoss | Energy Meters | 2016.03 VUIGB402

Installation & User Guide SonoSelect and SonoSafe

2.5 Mounting of O-ring and temperature sensor

One temperature sensor is factory mounted in the flow sensor. The other must be mounted in the opposite

pipe relative to the flow sensor installation.

Mount O-ring

on pin.

Insert pin with

O-ring.

Position O-ring.

Remove pin.

Moist and insert sen-

sor probe.Tighten at

torque 12 ± 2 Nm.

To ensure accuracy and a tight seal the sensor installation should comply to EN1434-2 annex A:

Key

Threaded connec-

tion size A

Tapping bore

size B

G½ 18.5 mm

G¾ 24 mm

G1 30.5 mm

Note:

Tolerance on machined dimensions = ± 0.5 mm.

Pipe fittings for use with probe type DS (Direct Short).

: provision for security sealing.

VUIGB402 © Danfoss | Energy Meters | 2016.03 | 7

Installation & User Guide SonoSelect and SonoSafe

2.6 Communication (Expansion modules)

General

Baud rate supported: 300, 2400, 4800, 9600 (auto baud detect).

Primary and secondary addressing supported.

Primary address: sssssvvNNyyww Secondary address: sssssvvNNyyww

Modules and terminal overview

Wired M-BUS + 2 x pulse input Application and data link layer according to EN13757-3

Wireless OMS + 2 x pulse input Application and data link layer according to EN13757-4 and OMS

with 868.95 MHz

Wired RS-485 + 2 x pulse input RS-485 Physical layer Modbus or M-Bus protocol supported

Terminals and cables

Communication Name Terminal No.

M-Bus

Meter bus (blue or orange) 24

Meter bus (blue or orange) 25

Pulse input

Remote pulse input 1 50

GND 51

Remote pulse input 2 52

GND 53

RS-485

+12V supply (Green and white) 61

RS485 Modbus interface (Blue and white) 62

RS485 Modbus interface (Blue) 63

GND (Green) 64

Cable specification

Pulse input cables <10 m

To ensure IP protection class connecting cable outer

jackets must be

Ø4.2 ± 0.1 mm

Communication cables delivered with heat meter.

Cable ends are stripped with crimped ferule.

1.0 m

8 | © Danfoss | Energy Meters | 2016.03 VUIGB402

Installation & User Guide SonoSelect and SonoSafe

2.7 Installation of module/cable

Before handling module

PCB ensure relevant ESD

regulations are observed

(IEC 61340-5-1).

Break wired seal for

enclosure.

Cut rubber parallel to enclosure.

Insert module follow-

ing guide on PCBA

cover.

Insert cable through

hole, connect cable

and fix to screw termi-

nals matching color

and terminal numbers.

Fix cable(s) to cable

relief. Outer jacket

no longer than 9 mm

from cable relief (line).

Press down.

Close enclosure making sure that no cables inter-

fere with rubber sealing and other internal parts.

Click!

Reset tamper alarm via Sono-

App for SonoSelect 10.

For module configuration, see

SonoApp user guide.

VUIGB402 © Danfoss | Energy Meters | 2016.03 | 9

Installation & User Guide SonoSelect and SonoSafe

2.8 Battery

Before handling

module PCB ensure

relevant ESD regu-

lations are observed

(IEC 61340-5-1).

Break installation

seal and open en-

closure.

Disconnect battery

connector and

remove battery.

Short circuit battery

connectors on PCB

using a small flat

head screwdriver.

Connect new battery

to PCB.

Fit battery

in enclosure.

Close enclosure

making sure that no

cables interfere with

rubber sealing or

other internal parts.

Confirm battery

change by pressing

the button 2 times

within 120 seconds.

Reset tamper alarm

(E13) via SonoApp

for SonoSelect 10.

10 | © Danfoss | Energy Meters | 2016.03 VUIGB402

Installation & User Guide SonoSelect and SonoSafe

3. Commissioning

3.1 Bleeding

1. Bleed the system until the flow rate display is steady.

2. Make sure no error codes are displayed.

3. Check the display for a plausible indication of flow rate and temperatures.

4. For SonoSelect: Run installation check using Bluetooth dongle 014U1963 and SonoApp service tool.

3.2 Supply/return configuration

Only available for SonoSelect: Use Bluetooth dongle 014U1963 and SonoApp service tool/Configuration

3.3 Meter sealing









Tamper monitor/

access level 1



Test seal

(verification mode)



Factory seal

3.4 IP class

Calculator IP65 (SonoSelect) / IP54 (SonoSafe)

Flow sensor IP65

Temperature sensor IP65

Note: The IP class can be compromised if cables are subjected to angled tension.

Installation & User Guide SonoSelect and SonoSafe

4. Function overview

4.1 Menu structure

HoursAlarm

Energy

Volume

LOOP 1

Supply temp. Display test/All on

Power

Flow

LOOP 2

Accounting date Monthly date 1 >> Monthly date 12

LOOP 3

Accumulated

Current

History log

2 sec.

5 sec.

click

Return temp.

2 sec.

Installation & User Guide SonoSelect and SonoSafe

4.2 Display explanation

Working symbol Supply/return mounted installation

Accumulated energy Alarm

Accumulated flow Service/maintenance

Total hours Battery full or low

Instant power Wired communication

Instant flow Wireless communication

Supply temperature Pulse

Return temperature Decimal emphasizer

Temperature difference Units field

4.3 Alarms

E01 System error E09 Low transducer signal

E02 PCB error E10 Transducer error

E03 Battery empty (less than 1 month) E11 Outside measured range

E04 Battery low voltage E12 Negative flow

E05 Battery low (less than 12 months) E13 Tamper alarm

E06 Supply Temperature Error E14 High flow > qss

E07 Return Temperature Error E15 Battery consumption too high

E08

Absolute/Difference temperature outside

accumulated range

E16 Display overflow (energy/volume)

Installation & User Guide SonoSelect and SonoSafe

5. Device overview

1. Display

2. PCBA

3. Cover part (PC)

4. Battery (Lithium)

5. Enclosure connection (PC)

6. Transducer (PZT/stainless steel/

PEI)

7. Spool piece (Brass)

8. Liner fixture (PPS/PEI/stainless

steel)

9. Liner (PPS)

10. Top part (PC, TPE)

11. Module (PCB)

12. Bottom part (PC)

13. Temperature sensor

6. Disposal

Item Material Disposal

Battery

AA-cell Lithium/thionyl chloride 620

mg Lithium

Approved deposit for

lithium batteries

PCBA with display

Coppered epoxy laminate components

soldered on, PC, TPE

Electronic waste

Cables Copper with PUR or PVC jackets Cable recovery

Flow sensor

(including transducer and liner)

Brass, stainless steel, PPS Metal recovery

Transducer PZT, stainless steel, PEI

Approved deposit for

PZT

Other plastic parts PC, PPS, PEI, TPE Plastic recovery

Installation & User Guide SonoSelect and SonoSafe

Danfoss A/S

Energy Meters • Ulvehavevej 61 • DK-7100 Vejle • Denmark

Phone: +45 7488 8500 • Fax: +45 7488 8501

[email protected]om • www.heating.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter

its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential

changes being necessary in specifications already agreed.

All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S.

Danfoss SonoSelect and SonoSafe User guide

Brand: Danfoss

Model: SonoSelect and SonoSafe

Category: Measuring, testing & control

Type: User guide

Download PDF

report

Danfoss SonoSelect and SonoSafe User guide

Danfoss SonoSelect and SonoSafe User guide

Related papers

Other documents