Pulsar ARAD2 Operating instructions

Type
Operating instructions
INSTALLATION GUIDE
ENGLISH
Code: ARAD2
Name: RACK ENCLOSURE 2U
Metallic enclosure for RACK cabinets: CCTV, AC, I&HAS, RTV, LAN
IM ARAD2
Edition: 1st from 25.10.2012
Supersedes: -------------------
EN*
1. Intended use:
Due to its design, the ARAD2 enclosure is intended for mounting inside RACK 19'' cabinets. This general-purpose
enclosure may serve as an auxiliary element for integrating CCTV, AC, I&HAS, RTV, LAN systems in RACK 19'' cabinets. It
is intended for mounting alarm control panels, AC controllers, power supply units, batteries, etc.
2. Description.
The enclosure is equipped with a mounting plate intended for mounting transformers or power supply units. The
enclosure can accommodate a 7Ah/12V battery and it features tampering protection (against unwanted opening).
There is also a possibility to mount extra tampering protection units (but not more than three PKAZ001CZ). To enable
leading cables into the enclosure, one can buy a cable protection conduit of any length and a cable gland. The conduits
and the cable glands are available at the following codes:
1) ARAP16 – angle cable gland, inside diameter 16 mm – connection between the protection conduit and the
enclosure
2) ARAP21 – angle cable gland, inside diameter 21 mm – connection between the protection conduit and the
enclosure
3) MM019 - cable protection conduit , inside diameter 16 mm
4) MM020 - cable protection conduit, inside diameter 21 mm
The enclosure ARAD2 can be joined with max. 4 ARAP16 or 3 ARAP21 cable glands.
To mount the ARAD2 enclosures inside a RACK cabinet, ARAS rails are needed. Their length depends on the
cabinet’s depth.
Three kinds of RACK rails are produced:
1) ARAS600 – rails for 600mm deep RACK cabinets
2) ARAS800 – rails for 800mm deep RACK cabinets
3) ARAS1000 – rails for 1000mm deep RACK cabinets
Optionally, ARAW45 fans can be mounted. They trigger airflow inside the enclosure after exceeding 45
o
C. One
enclosure can accommodate max. two fan units in the rear part of the enclosure.
2
Dimensions of the mounting plate.
3
3. Assembling instructions:
3.1. Mount the M6 cage nuts to the RACK cabinet, as shown in the picture below. Then, mount the ARAS rails
(accordingly to the cabinet’s depth). Take notice of the correct positioning of the horizontal rails. Adjust their length
between the front and back RACK profiles.
3.2. Place the ARAD enclosure onto the slid-out ARAS rails. Next, bolt it from the inside with 6xM4 bolts
(included). The enclosure is fixed to the front part of the RACK rails with four M6 screws.
4. Specifications.
SPECIFICATIONS
Fitting battery 7Ah/12V
Tampering protection 1x – against unwanted opening of the enclosure
Max. load of TAMPER output 500mA@50VDC
Enclosure: IP IP 20
Operation temperature -10ºC÷40ºC
Relative humidity RH – max. 90 [%]
Internal dimensions
(W x H x D)
390 x 70 x 395
[-/+2] [mm]
Possible extra accessories
fan with temperature sensor – MAX. 2 pcs
angle cable glands with cable protection conduit, fi16;fi21
Materials
sheet metal DC01, 1,0mm thick
rust protection
colour: RAL 9005 BLACK
Use inside
Net weight ~5.6 [kg]
Gross weight ~6.4 [kg]
4
5. Accessories.
Specifications of the transformers that can be mounted in the enclosure:
CODE
NAME C S U I
U1 or U2 or U3
I1 or I2 or I3
F t
AWT053 TRP 20/12/14
PC/ABS
UL94 V-0
IP20
20VA 230V/AC 0,12A
12V or 14V
1,6A or 1,4A
T 200mA/250V 130
o
C
AWT050 TRP 20/16/18
PC/ABS
UL94 V-0
IP20
20VA 230V/AC 0,12A
16V or 18V
1,2A or 1,0A
T 200mA/250V 130
o
C
AWT268 TRZ 20/16/18
PC/ABS
UL94 V-0
IP43
20VA 230V/AC 0,12A
16V or 18V
1,2A or 1,0A
T 200mA/250V 130
o
C
AWT150 TRP 40/16/18
PC/ABS
UL94 V-0
IP20
40VA 230V/AC 0,20A
16V or 18V
2,2A or 2,0A
T 315mA/250V 130
o
C
AWT468 TRZ 40/16/18
PC/ABS
UL94 V-0
IP43
40VA 230V/AC 0,20A
16V or 18V
2,2A or 2,0A
T 315mA/250V 130
o
C
AWT037
TOR 50/16/18/20 - 50VA 230V/AC 0,25A
16V or 18V or 20V
3,0A or 2,8A or 2,5A
T 500mA/250V
130
O
C
AWT049
TOR 50/17/24/30 - 50VA 230V/AC 0,25A
17V or 24V or 30V
2,9A or 2,1A or 1,7A
T 500mA/250V
130
O
C
AWT039
TOR 80/16/18/20 - 80VA 230V/AC 0,4A
16V or 18V or 20V
5,0A or 4,5A or 4,0A
T 630mA/250V
130
O
C
AWT048
TOR 80/17/24/30 - 80VA 230V/AC 0,4A
17V or 24V or 30V
4,7A or 3,3A or 2,7A
T 630mA/250V
130
O
C
C- enclosure of the transformer
S - power
U – supply voltage
I – current drawn with nominal network load of ~230V
U1 / U2/ U3 – secondary voltage
I1 / I2/ I3 – nominal output current
F – F fuse in the primary circuit of the transformer
t- thermal fuse 130
o
C, non-returnable
Specifications of the power supply units that can be mounted in the enclosure::
CODE Current Power of the PSU Output voltage range PSU type
PS251220
12V/2A 25W 12V÷15VDC switched mode PSU
PS401230
12V/3A 40W 12V÷15VDC switched mode PSU
PS601250
12V/5A 60W 12V÷15VDC switched mode PSU
PS1001270
12V/7A 100W 12V÷15VDC switched mode PSU
PS15012100
12V/10A 150W 12V÷15VDC switched mode PSU
PS2001214
12V/14A 200W 12V÷15VDC switched mode PSU
PS402418
24V/1,8A 40W 24V÷28VDC switched mode PSU
PS1002435
24V/3,5A 100W 24V÷28VDC switched mode PSU
PS2002470
24V/7A 200W 24V÷28VDC switched mode PSU
PS602425
24V/2,5A 60W 24V÷28VDC switched mode PSU
PS1502450
24V/5A 150W 24V÷28VDC switched mode PSU
PSB351225
13,8V/2,5A 35W 12V÷14VDC buffer, switched mode PSU
PSB501235
13,8V/3,5A 50W 12V÷14VDC buffer, switched mode PSU
5
PSB1001270
13,8V/7A 100W 12V÷14VDC buffer, switched mode PSU
PSB15512110
13,8V/11A 155W 12V÷14VDC buffer, switched mode PSU
PSB352413
27,6V/1,3A 35W 24V÷28VDC buffer, switched mode PSU
PSB502418
27,6V/1,8V 50W 24V÷28VDC buffer, switched mode PSU
PSB1002435
27,6V/3,5A 100W 24V÷28VDC buffer, switched mode PSU
PSB1552455
27,6V/5,5A 155W 24V÷28VDC buffer, switched mode PSU
Fig.1. Examples of configurations.
ARAD2 with the ARAP16 (ARAP21) cable glands
and the MM019 (MM020) cable protection conduits
ARAD2 with the ARAW45 fan
PRODUCER
Pulsar K.Bogusz Sp.j.
Siedlec 150,
32-744 Łapczyca, Poland
Tel. (00 48) 14-610-19-40, Fax. (00 48) 14-610-19-50
e-mail:
biuro@pulsar.pl, sales@pulsar.pl
http:// www.pulsar.pl, www.zasilacze.pl
WARRANTY :
24 months from the date of purchase, 36 months from the production date.
THE WARRANTY IS VALID only upon presentation of the item’s proof of purchase.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Pulsar ARAD2 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI