Pulsar ARAD4 Operating instructions

INSTALLATION GUIDE

ENGLISH

Code: ARAD4

Name: RACK ENCLOSURE 2U

Metallic enclosure for RACK cabinets: CCTV, AC, I&HAS, RTV, LAN

IM ARAD4

Edition: 1st from 25.10.2012

Supersedes: -------------------

EN*

1. Intended use:

Due to its design, the ARAD4 enclosure is intended for mounting inside RACK 19'' cabinets. This general-purpose

enclosure may serve as an auxiliary element for integrating CCTV, AC, I&HAS, RTV, LAN systems in RACK 19'' cabinets. It

is intended for mounting alarm control panels, AC controllers, power supply units, batteries, etc.

2. Description.

The enclosure is equipped with a mounting plate intended for mounting transformers Or Power supply units. The

enclosure can accommodate a 17Ah/12V battery and it features tampering protection (against unwanted opening).

There is also a possibility to mount extra tampering protection units (but not more than three PKAZ001CZ). To enable

leading cables into the enclosure, one can buy a cable protection conduit of any length and a cable gland. The conduits

and the cable glands are available at the following codes:

1) ARAP16 – angle cable gland, inside diameter 16 mm – connection between the protection conduit and the

enclosure

2) ARAP21 – angle cable gland, inside diameter 21 mm – connection between the protection conduit and the

enclosure

3) MM019 - cable protection conduit , inside diameter 16 mm

4) MM020 - cable protection conduit, inside diameter 21 mm

The enclosure ARAD4 can be joined with max. 8 ARAP16 or 8 ARAP21 cable glands.

To mount the ARAD4 enclosures inside a RACK cabinet, ARAS rails are needed. Their length depends on the

cabinet’s depth.

Three kinds of RACK rails are produced:

1) ARAS600 – rails for 600mm deep RACK cabinets

2) ARAS800 – rails for 800mm deep RACK cabinets

3) ARAS1000 – rails for 1000mm deep RACK cabinets

Optionally, ARAW45 fans can be mounted. They trigger airflow inside the enclosure after exceeding 45

o

C. One

enclosure can accommodate max. two fan units in the rear part of the enclosure.

2

3

Dimensions of the mounting plate and the hinged plate.

3. Assembling instructions:

3.1. Mount the M6 cage nuts to the RACK cabinet, as shown in the picture below. Then, mount the ARAS rails

(accordingly to the cabinet’s depth). Take notice of the correct positioning of the horizontal rails. Adjust their length

between the front and back RACK profiles.

3.2. Place the ARAD enclosure onto the slid-out ARAS rails. Next, bolt it from the inside with 6xM4 bolts

(included). The enclosure is fixed to the front part of the RACK rails with four M6 screws.

4

4. Specifications.

SPECIFICATIONS

Fitting battery 17Ah/12V

Tampering protection 1x – against unwanted opening of the enclosure

Max. load of TAMPER output 500mA@50VDC

Enclosure: IP IP 20

Operation temperature -10ºC÷40ºC

Relative humidity RH – max. 90 [%]

Internal dimensions

(W x H x D)

390 x 162 x 395

[-/+2] [mm]

Possible extra accessories

fan with temperature sensor – MAX. 2 pcs

angle cable glands with cable protection conduit, fi16;fi21

Materials

sheet metal DC01, 1,0mm thick

rust protection

colour: RAL 9005 BLACK

Use inside

Net weight ~8,1 [kg]

Gross weight ~9,3 [kg]

5. Accessories.

5

C- enclosure of the transformer

S - power

U – supply voltage

I – current drawn with nominal network load of ~230V

U1 / U2/ U3 – secondary voltage

I1 / I2/ I3 – nominal output current

F – F fuse in the primary circuit of the transformer

t- thermal fuse 130

o

C, non-returnable

Specifications of the power supply units that can be mounted in the enclosure::

CODE Current Power of the PSU Output voltage range PSU type

PS251220

12V/2A 25W 12V÷15VDC switched mode PSU

PS401230

12V/3A 40W 12V÷15VDC switched mode PSU

PS601250

12V/5A 60W 12V÷15VDC switched mode PSU

PS1001270

12V/7A 100W 12V÷15VDC switched mode PSU

PS15012100

12V/10A 150W 12V÷15VDC switched mode PSU

PS2001214

12V/14A 200W 12V÷15VDC switched mode PSU

PS402418

24V/1,8A 40W 24V÷28VDC switched mode PSU

PS1002435

24V/3,5A 100W 24V÷28VDC switched mode PSU

Specifications of the transformers that can be mounted in the enclosure:

CODE

NAME C S U I

U1 or U2 or U3

I1 or I2 or I3

F t

AWT053 TRP 20/12/14

PC/ABS

UL94 V-0

IP20

20VA 230V/AC 0,12A

12V or 14V

1,6A or 1,4A

T 200mA/250V 130

o

C

AWT050 TRP 20/16/18

PC/ABS

UL94 V-0

IP20

20VA 230V/AC 0,12A

16V or 18V

1,2A or 1,0A

T 200mA/250V 130

o

C

AWT268 TRZ 20/16/18

PC/ABS

UL94 V-0

IP43

20VA 230V/AC 0,12A

16V or 18V

1,2A or 1,0A

T 200mA/250V 130

o

C

AWT150 TRP 40/16/18

PC/ABS

UL94 V-0

IP20

40VA 230V/AC 0,20A

16V or 18V

2,2A or 2,0A

T 315mA/250V 130

o

C

AWT468 TRZ 40/16/18

PC/ABS

UL94 V-0

IP43

40VA 230V/AC 0,20A

16V or 18V

2,2A or 2,0A

T 315mA/250V 130

o

C

AWT

5161820

TRZ 50/16/18/20

PC/ABS

UL94 V-0

IP43

50VA 230V/AC 0,25A

16V or 18V or 20V

3,0A or 2,8A or 2,5A

T 500mA/250V 130

o

C

AWT

5172430

TRZ 50/17/24/30

PC/ABS

UL94 V-0

IP43

50VA 230V/AC 0,25A

17V or 24V or 30V

2,9A or 2,1A or 1,7A

T 500mA/250V 130

o

C

AWT

8161820

TRZ 80/16/18/20

PC/ABS

UL94 V-0

IP43

80VA 230V/AC 0,4A

16V or 18V or 20V

5,0A or 4,5A or 4,0A

T 630mA/250V 130

o

C

AWT

8172430

TRZ 80/17/24/30

PC/ABS

UL94 V-0

IP43

80VA 230V/AC 0,4A

17V or 24V or 30V

4,7A or 3,3A or 2,7A

T 630mA/250V 130

o

C

AWT037

TOR 50/16/18/20 - 50VA 230V/AC 0,25A

16V or 18V or 20V

3,0A or 2,8A or 2,5A

T 500mA/250V

130

O

C

AWT049

TOR 50/17/24/30 - 50VA 230V/AC 0,25A

17V or 24V or 30V

2,9A or 2,1A or 1,7A

T 500mA/250V

130

O

C

AWT039

TOR 80/16/18/20 - 80VA 230V/AC 0,4A

16V or 18V or 20V

5,0A or 4,5A or 4,0A

T 630mA/250V

130

O

C

AWT048

TOR 80/17/24/30 - 80VA 230V/AC 0,4A

17V or 24V or 30V

4,7A or 3,3A or 2,7A

T 630mA/250V

130

O

C

6

PS2002470

24V/7A 200W 24V÷28VDC switched mode PSU

PS602425

24V/2,5A 60W 24V÷28VDC switched mode PSU

PS1502450

24V/5A 150W 24V÷28VDC switched mode PSU

PSB351225

13,8V/2,5A 35W 12V÷14VDC buffer, switched mode PSU

PSB501235

13,8V/3,5A 50W 12V÷14VDC buffer, switched mode PSU

PSB1001270

13,8V/7A 100W 12V÷14VDC buffer, switched mode PSU

PSB15512110

13,8V/11A 155W 12V÷14VDC buffer, switched mode PSU

PSB352413

27,6V/1,3A 35W 24V÷28VDC buffer, switched mode PSU

PSB502418

27,6V/1,8V 50W 24V÷28VDC buffer, switched mode PSU

PSB1002435

27,6V/3,5A 100W 24V÷28VDC buffer, switched mode PSU

PSB1552455

27,6V/5,5A 155W 24V÷28VDC buffer, switched mode PSU

Fig.1. Examples of configurations.

ARAD4 with the ARAP16 (ARAP21) cable glands

and the MM019 (MM020) cable protection conduits

ARAD4 with the ARAW45 fan

PRODUCER

Pulsar K.Bogusz Sp.j.

Siedlec 150,

32-744 Łapczyca, Poland

Tel. (00 48) 14-610-19-40, Fax. (00 48) 14-610-19-50

e-mail:

biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

WARRANTY :

24 months from the date of purchase, 36 months from the production date.

THE WARRANTY IS VALID only upon presentation of the item’s proof of purchase.

Pulsar ARAD4 Operating instructions

Pulsar ARAD4 Operating instructions

Related papers

Other documents