Yamaha PDS-242 Owner's manual

PDS-242
Yamaha
Brand
Yamaha
Model
PDS-242
Type
Owner's manual

Yamaha PDS-242 is a pedestal designed for use with specific Yamaha plasma monitor models. It offers a stable and secure way to mount your plasma monitor on a tabletop or attach it to a wall or post using commercially available cords or chains. The pedestal includes all necessary hardware for both tabletop and wall mounting, ensuring a safe and easy installation.

Yamaha PDS-242 is a pedestal designed for use with specific Yamaha plasma monitor models. It offers a stable and secure way to mount your plasma monitor on a tabletop or attach it to a wall or post using commercially available cords or chains. The pedestal includes all necessary hardware for both tabletop and wall mounting, ensuring a safe and easy installation.

To ensure correct usage
Using the hooks at center of the rear of the plasma monitor, a
commercially available cord or chain, and a clamp, secure the
set to a firm wall or to a wall post.
Hook
Cord or
chain
Cord
or
chain
Clamp
Wood
screw
(Two places)
Securing to a wall or post Securing to a tabletop
Using commercially available wood screws
(two), fasten the set to the clamping screw
holes on the rear of the pedestal as shown.
■ Always use at least two people to perform installation work.
Injury could result from dropping heavy objects.
■ Use the specified bolts and screws in the specified places and tighten firmly.
Failure to do this could cause injury if the plasma monitor falls.
■ Avoid installing in locations where the temperature and humidity are excessively high,
and where contact with water is possible.
These can result in fire or electrical shock.
■ Do not block the ventilation holes. Ensure that there is sufficient clearance for ventilation.
The internal temperature of the plasma monitor could elevate possibly resulting in fire.
■ Do not alter any parts or use broken parts.
This could result in the plasma monitor falling causing injury.
■ Do not mount the plasma monitor in an unstable location.
The monitor could fall or break, resulting in physical injury.
CAUTION
WARNING
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan 3023575
IP
2003 All rights reserved.
PDS-242
Pedestal
Installation Instructions
Thank you for purchasing the Pedestal.
To ensure correct usage, please read this instruction manual thoroughly. After reading,
please store this manual in a safe place for future reference.
This pedestal is for use only with the following models:
PDM-4210, PDM-4210E
■ Request an installation specialist to install this unit.
■ YAMAHA assumes absolutely no responsibility for injuries and damages that may
occur due to improper installation and handling.
PDS-242_E 2003.12.11 11:23 1
1030 (40-9/16)
700 (27-9/16) 300 (11-13/16)
124
(4-7/8)
89
(3-1/2)
636 (25-1/16)
713 (28-1/16)
77
(3)
397 (15-5/8)
Usage cautions
Dimension diagram
■ Do not allow an adhesive material, such as an adhesive tape, into
contact with the surface of the pedestal, as they may cause the exterior
surface to peel.
■ Wipe off dirt using a dry cloth. To remove ingrained dirt, use a cloth
saturated with a diluted neutral detergent solution and squeezed until
damp. Use of organic solvents, such as benzine, thinner, and household
wax, for cleaning could result in a degenerated or discolored material.
(When using a chemical duster, observe the relevant instructions.)
Assembly Method
Prepare a phillips screwdriver before proceeding with assembly.
Assembling the pedestal Attaching the Plasma Monitor to the pedestal
Product Specifications
Parts Configuration Chart
Included in the parts package
M5
x
20 screws
x
4
M6
x
30 screws
x
4
Cable clamp
x
2
Pedestal base
x
1
Support
x
2
External
Dimensions
700 (W)
x
184 (H)
x
300 (D) mm
(27-9/16 (W) x 7-1/4 (H) x 35-7/16 (D) inches)
Weight
4.2kg
(9 lbs. 4 oz.)
Main material
/Surface
treatment
Pedestal base, Support : Aluminum alloy / Baked paint finish
1. Insert the support into the pedestal base and secure it in
position by tightening four M5
x
20 screws from the bottom.
Pedestal base
Support (2)
M5
x
20 screw
(4)
2. Insert the pedestal support into the square holes on the
bottom of the plasma monitor.
Plasma monitor
Pedestal
3. Fix the pedestal to the plasma monitor using four M6
x
30
screws.
M6
x
30 screw (4)
4. Connect the cables to the plasma monitor, attach the
cable clamps to the pedestal where necessary, and fasten
the cables to the clamps.
Cable clamp
Unit: mm (inches)
PDS-242_E 2003.12.11 11:23 2
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Yamaha PDS-242 Owner's manual

PDS-242
Yamaha
Brand
Yamaha
Model
PDS-242
Type
Owner's manual

Yamaha PDS-242 is a pedestal designed for use with specific Yamaha plasma monitor models. It offers a stable and secure way to mount your plasma monitor on a tabletop or attach it to a wall or post using commercially available cords or chains. The pedestal includes all necessary hardware for both tabletop and wall mounting, ensuring a safe and easy installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents