Gianni Industries PBA-860/860DE Installation guide

Gianni Industries
Brand
Gianni Industries
Model
PBA-860/860DE
Category
Security door controllers
Type
Installation guide
Copyright Gianni Industries, Inc. All Rights Reserved.
P-MU-PBA-860DE Published: 2016.05.05
The PBA-860DE Micro Switch Bar is designed for
doors openings that require a delayed egress where
you may already have a standard magnetic lock
installed. We introduce you to our new and easy
way to make it work! Our PBA-860 DE offers easy
installation and functionality. The PC board is
completely adjustable for both delay and nuisance,
so it meets all the NFPA and IBC requirements.
For life safety and security reasons, please install
with a fail safe device. We recommend a GEM
electromagnetic lock. We also recommend you use
a UL listed power supply and battery backup in case
of power failure.
PBA-860DE Delayed Egress Micro Switch Bar
15 Sec. 30 Sec.
4
ON ECE
N.C. is triggered
N.O. is triggered
4
ON ECE
0 Second
1 Second
2 Second
3 Second
Delay Egress Setting Emergency Signal Input (N.C. / N.O.)
Dip Switch 4Setting of the Depressed Time of Micro Switch Bar
1. (1) The nuisance delay time can be set to 0 sec, 1 sec, 2 sec, or 3 sec before triggering the piezo alarm when the door remains locked. Set
up the time by moving dip switch 1 & 2. Note: The 0 second nuisance does not include the 200 millisecond de-bounce delay - it was added to
eliminate false triggering. The actual delay is 0.2 seconds.
PBA-860DE PC Board Diagram
EMERGENCY EXIT
PUSH UNTIL
ALARM SOUNDS
DOOR CAN BE OPENED IN
15 SECONDS
Door sign included
*Push to Exit on
Bar is Optional
2.42”
34.45” (875mm)
2.6”
32.81” (833.5mm)
(66mm)
(61.5mm)
Nuisance Delay Setting
12
ON ECE
12
ON ECE
12
ON ECE
12
ON ECE
3
ON ECE
3
ON ECE
Dip Switch 1 & 2
Operation Notes
2. (2) When the micro switch bar is pressed, the delay egress count-down begins and the piezo alarm will go off (based on nuisance delay
settings). Adjust dip switch #3 to set delay egress to 15 or 30 seconds for locking device to release. Verify with your AHJ (Authority Having
Jurisdiction) as to which time you must follow.
The alarm beeps every single second before the delay egress ends. After the ending of delay egress, the piezo continuously sounds until a
RESET is triggered by key switch or other mode of reset. *The reset funciton can be used during the egress delay.
3. (3) When the emergency signal input (CUT IN) is triggered under emergency circumstances, the magnetic lock on a door will be released to
exit immediately. *Verify if you need this to go into NO or NC Status for Emergency and ensure it is in correct position.
The bypass function can be used with access control system to exit the door without putting the PBA-860DE into alarm, by using the PASS
input on the PC Board.
Instruction Manual
Dip Switch #3
)3()2()1(
95 db
Piezo
Sounder
PBA-860DE Instructions
Switch signal output 2
(for external device)
RED(N.C.)
BLACK(COM.)
WHITE(N.O.)
Terminal Connection
RESET
RESET
OUT -
OUT +
V -
V +
N.C.
COM.
N.O.
CUT IN
CUT IN
Reset input (Keyswitch)
Fail-safe electrified lock contacts 1
Power input 12~24 VDC/AC
Relay contacts for external buzzer
Rating: 1A@24VDC, 0.5A/125VAC
Emergency signal input
(Door Pull /Fire panel system)
START
PASS
Switch signal output 1
(for PBA-860DE)
Connection to a keypad or reader for
authorized egress without sounder
OUT-
OUT+
Fail-safe electrified lock contacts 2
Switch Signal
Output 1
ST
A
RT
R
E
S
ET
R
ES
E
T
N.C
.
C
O
M.
N
.
O.
C
UT
I
N
PUT
C
U
T
I
NPU
T
RELAY
V -
V
+
Power
1234
ON ECE
Buzzer
PASS HALL
OUT+
OUT
-
OUT+
OUT-
Electromagnetic Lock
HALL
Door Ajar Input
When the door is left open for more
than 3 seconds, a door ajar alarm
will sound until the door is closed.
PBA-860 Micro Switch Push Bar
Electromagnetic Lock Door Loop
PBA-860
Fig.A
Directly control the fail-safe electromagnetic lock
Electromagnetic
The PBA-860 mechanical micro switch push bar is designed for use on emergency exit doors or large-scale
outswing doors. Pressing on the bar activates the interior micro switch, which will remove power to the
electromagnetic lock, in turn unlocking the door for immediate egress.
Copyright Gianni Industries, Inc. All Rights Reserved.
875(L)*66(W)*61.5mm(D)
Finish: Clear anodized
Switch rated 5 Amp/125VAC
Fig.B
P-MU-PBA860-N Published: 2019.03.28
Power
Supply
Lock
(Fail-safe)
Access Control Device
Request-to-exit contact
Relay
N.C.
Com.
N.O.
N.C.
N.O.
N.C.
Com.
N.O.
N.C.
Com.
N.O.
N.C.
Com.
N.O.
N.C.
Com.
N.O.
Power
Supply
Electromagnetic
Lock
(Fail-safe)
Connect the access control device
N.C.
.
Com.
N.O.
N.C.
Com.
N.O.
Double pole
micro sw itch output
875
835
61.5
66
  • Page 1 1
  • Page 2 2

Gianni Industries PBA-860/860DE Installation guide

Gianni Industries
Brand
Gianni Industries
Model
PBA-860/860DE
Category
Security door controllers
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents