Tripp Lite SRGASKET Airflow Kit Owner's manual

Brand: Tripp Lite

Model: SRGASKET Airflow Kit

Type: Owner's manual

Tripp Lite SRGASKET Airflow Kit is a comprehensive solution for optimizing airflow in server racks and enclosures. It prevents the recirculation of warm exhaust air within the enclosure, seals front-to-rear airflow pathways, and supports equipment requiring side-to-side airflow. The kit's compatibility with 25U, 42U, and 48U SmartRack™ enclosures and its adherence to industry standards ensure seamless integration into existing data center setups.

Key features of the SRGASKET Airflow Kit include:

• Improved airflow management, preventing hot spots and ensuring optimal equipment performance • Compatibility with various rack and enclosure types

Key features of the SRGASKET Airflow Kit include:

• Improved airflow management, preventing hot spots and ensuring optimal equipment performance • Compatibility with various rack and enclosure types

Owner’s Manual

SRGASKET

Airﬂow Optimization Kit

Introduction

SRGASKET Airﬂow Optimization Kit Beneﬁts

• Preventsrecirculationofwarmequipmentexhaustinsideenclosures

• Closessidegapsandsealsfront-to-rearairowpathway

• Alsosupportsequipmentthatrequiresside-to-sideairow

• Facilitateshot-aisle/cold-aisledatacentercongurations

• Fullycompatiblewith25U,42Uand48USmartRack™enclosures

Important Safety Instructions

SAVE THESE INSTRUCTIONS

Thismanualcontaininstructionsandwarningsthatmustbefollowedduringtheinstallationandoperationoftheproductdescribedinthismanual.

Failuretocomplymayinvalidatethewarranty.

• Theinstructionsinthismanualareforcommonrackandrackenclosuretypesandmaynotbeappropriateforallmountingapplications.Youmust

determinethetnessofhardwareandproceduresbeforemounting.Ifhardwareorproceduresarenotsuitableforyourapplication,contactthe

manufacturerofyourrackorrackenclosureforasolution.

• Rackmountequipmentmaybeextremelyheavy—becarefulwhenmovingorliftingequipment.Useoneormoreassistantsifnecessary.

• Beforeapplyingadhesivestrips,measuresidepanels,gasketsandmountingrailscarefullytoassureproperalignment.Payparticularattentionto

accommodatingthehorizontalstrutsofeachsidepanel.

• Attachgasketstomountingrails,notsidepanels.Ifgasketsareattachedtosidepanels,theywillnotbeeffectivewhenmountingraildepthisadjusted.

• Ifequipmentrequiresside-to-sideairow,modifyinstallationprocedureasspeciedinSide-to-Side Airﬂow Installation.

1111W.35thStreet,Chicago,IL60609USA

+1.773.869.1234•www.tripplite.com

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Standard Installation

Parts List

 7-1/4inch(184.5mm)gasketwithadhesivestrip(4) 

 5inch(127mm)gasketwithadhesivestrip(4)

 24-7/8inch(632mm)gasketwithadhesivestrip(4) 

 3-7/8inch(98.5mm)gasketwithoutadhesivestrip(6)

Installation Procedure

 Removeyourenclosure’ssidepanels.Leavegapsofapproximately1/8inch(3mm)asshowninthediagramtoaccommodateeachsidepanel’stop,

interiorandbottomhorizontalstruts.Useapenciltomarktheappropriateplacementofeachgasketandgapasshowninthediagram.Conrmproper

alignmentwithsidepanelsbeforeproceeding.

 Foreachadhesivegasket

,

or

showninthediagram,removethebackingfromtheadhesive

stripandattachthegaskettotheforwardmountingrailasshowninthediagram.Repeatforboth

oftheenclosure’sforwardmountingrails.Note:Ifequipmentrequiresside-to-sideairow,modify

installationprocedureasspeciedinSide-to-Side

Airﬂow Installation.

 Insertanon-adhesivegasket

insideeachhorizontal

crossbeam.Compressthegasketmaterial,pushitinto

theopeningandarrangeittosealthegap.48Uand

42Uenclosureshaveatotalof6crossbeams.25U

enclosureshaveatotalof4crossbeams.

Side-to-Side Airflow Installation

Ifyourequipmentrequiresside-to-sideairow,followtheinstructionsfor

standardinstallationwiththefollowingexception:insteadofattaching

thegasketstotheforwardmountingrails,attachthegasketstoone

forwardmountingrail

andonerearmounting

rail.Attachgasketsto

thefrontleftandrear

rightrailsifequipment

requiresright-to-left

airow;attachgasketsto

thefrontrightandrear

leftrailsifequipment

requiresleft-to-right

airow.Thediagram

showsatopviewwith

thegasketposition



foreachconguration.

Warranty Registration

Visitwww.tripplite.com/warrantytodaytoregisterthewarrantyforyour

newTrippLiteproduct.You’llbeautomaticallyenteredintoadrawingfor

achancetowinaFREETrippLiteproduct!

Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.

Seewebsitefordetails.

TrippLitehasapolicyofcontinuousimprovement.Specicationsaresubjecttochange

withoutnotice.

MadeinChina.

(inside)

GAP

FRONT REAR

GAP

(inside)

GAP

Tr im to 6 / inches

(162 mm)

FRONT REAR

25U (Side View) 42U (Side View) 48U (Side View)

Configuration For

Front-to-Rear Airflow

ment

Configuration For

Side-to-Side (Right-to-Left)

Airflow E

ment

1111W.35thStreet,Chicago,IL60609USA

+1.773.869.1234•www.tripplite.com

20080519893-2819

Tripp Lite SRGASKET Airflow Kit Owner's manual

Brand: Tripp Lite

Model: SRGASKET Airflow Kit

Type: Owner's manual

Key features of the SRGASKET Airflow Kit include:

• Improved airflow management, preventing hot spots and ensuring optimal equipment performance • Compatibility with various rack and enclosure types

Download PDF

report

Tripp Lite SRGASKET Airflow Kit Owner's manual

Tripp Lite SRGASKET Airflow Kit Owner's manual

Related papers

Other documents