Tripp Lite SREXTENDER User manual

Brand: Tripp Lite

Model: SREXTENDER

Category: Racks

Type: User manual

Tripp Lite SREXTENDER is a rack enclosure extension frame that provides additional space for mounting rack-mount equipment. It is compatible with most standard 19-inch rack enclosures and can be used to add up to 48U of rack space. The SREXTENDER features a sturdy steel construction and includes all necessary hardware for easy installation. It also includes cable management brackets and a grounding cable for added safety and organization.

Owner’s Manual

SREXTENDER

Rack Enclosure Extension Frame

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this

manual. Failure to comply may invalidate the warranty.

• Theinstructionsinthismanualareforcommonrackenclosuretypesandmaynotbeappropriateforallmountingapplications.Youmust

determine the ﬁtness of hardware and procedures before mounting. If hardware or procedures are not suitable for your application, contact the

manufacturer of your equipment for a solution.

• Rackmountequipmentmaybeextremelyheavy—becarefulwhenmovingorliftingequipment.Useoneormoreassistantsifnecessary.

Preparation

Note: Tripp Lite recommends using an assistant during installation. Descriptions of left and right are relative to the rear of your rack

enclosure. Illustrations may differ slightly from your enclosure, but procedures are similar for 48U, 42U and 25U enclosures unless

otherwise noted.

• Phillips-headScrewdriver(user-supplied;cordlessscrewdriverrecommended)

Tools Required

1111W.35thStreet,Chicago,IL60609USA

(773)869-1234•www.tripplite.com

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Español 8

Français 15

A B C D E H N

48/42U

1-1

Preparation (continued)

Note: The hinge swivels

and 12 hinge swivel screws

are pre-installed in the vertical sections

through

Parts List (If any parts are missing, contact Tripp Lite.)

LowerLeftVerticalSection(1)

LowerRightVerticalSection(1)

UpperLeftVerticalSection(1)

UpperRightVerticalSection(1)

TopSection(1)

BottomSection(1)

1UBlankingPanels(3)

HingeSwivels(6-allpre-installed)

Hinges(4)

CableManagerBrackets(2)

M6x12mmFlat-HeadScrews(8)

M6x12mmPan-HeadScrews

andWashers(14total-12pre-installed)

M5x10mmPan-HeadScrews

andWashers(40)

GroundingCable(1)

M5x20mmPan-HeadScrewsand

Washers(4)

M4x8mmPan-HeadScrews

andWashers(8)

1 – Frame Assembly

Note: For 25U enclosures, you will use only the lower vertical sections

and

. You will not use the upper vertical sections

and

For 48U and 42U enclosures, you will use all four vertical sections.

(For25Uenclosures,skipthisstep.)Slidethelowerleftvertical

section

inside the upper left vertical section

as shown.

Repeatforthelowerrightverticalsection

and the upper right

vertical section

. The vertical sections are not interchangeable,

so refer to the diagram to conﬁrm that you’re assembling the

correct sections.

1-1

48U

42U

A AB B

C CD D

1-2

1-3

1-4

1-5

1 – Frame Assembly (continued)

(For25Uenclosures,skipthisstep.)Alignthesetoffourscrew

holes in the lower left vertical section

and the upper left

vertical section

.Usethelowersetofscrewholesfor48U

enclosures(thiswillmaketheverticalsectionlonger).Usethe

uppersetofscrewholesfor42Uenclosures(thiswillmakethe

verticalsectionshorter).InsertfourM5x10mmscrewsand

washers

andtightensecurely.(Startallthescrewsbefore

tightening.)Repeatforthelowerrightverticalsection

and the

upper right vertical section

Insert the lower end of the left vertical section into the

bottom section

asshown.Alignthescrewholes,insertfour

M5x10mmscrewsandwashers

andtightensecurely.(Start

allthescrewsbeforetightening.)Repeatthisstepfortheright

vertical section.

Insert the upper end of the left and right vertical sections into the

top section

.Alignthescrewholes,inserteightM5x10mm

screws and washers

andtightensecurely.(Startallthescrews

beforetightening.)

Insertthe1Ublankingpanels

into the top section

EachblankingpanelwillsnapintoplacewiththeTrippLitelogo

facingoutward.Theblankingpanelsmayberemovedtoinstall

standard19-inchrackaccessoriesupto3U–contactTrippLite

for more information.

1-2

1-3

1-4

1-5

48/42U

25U

42U

48U

1-6

1-7

1 – Frame Assembly (continued)

(For25Uenclosures,skipthisstep.)Attachthecablemanager

brackets

totheverticalsectionswithfourM5x10mmscrews

and washers

asshown.(For48Uenclosures,usetheupper

setofholes.For42Uenclosures,usethelowersetofholes.The

bracketswillfacedownward.)

UsetwoM6x12mmat-headscrews

to attach each hinge

as shown. Orient each hinge so that the pin is closer to the

outside of the frame than the inside.

1-6

1-7

48/42U

25U

90°

2-3

2-4

2-2

2-1

Loosenthescrews

attaching the hinge swivels

to the vertical

sectionsinthefourlocationsindicated.You will retighten the

screws in the next step, after attaching the frame to the rack

enclosure.

Unscrewthegroundingcableoftherackenclosure’srightrear

doorfromtherackenclosure.(Donotunscrewthecablefromthe

door).Repeatfortheleftreardoor.Savethescrewsandwashers

for later use.

Opentherightreardooruntilitisperpendicular(90degrees)to

the rear of the enclosure, lift it from the hinges and set it aside.

Repeatfortheleftreardoor.(Iftheenclosureisjoinedtoanother

enclosure,turnthedoorbacktowardtheenclosureasyouliftit

fromthehinges.)

With the aid of an assistant, lift the frame, align the frame’s hinge

swivelswiththerackenclosure’shingesandhangtheframefrom

thehinges.Whentheframeissecurelyalignedwiththerack

enclosure, tighten the hinge swivel screws that you loosened in

the previous step.

2-1

2-2

2-4

2 – Fixation du cadre (suite)

2-3

48/42U

2-5

2-6

2-7

2-8

2 – Frame Attachment (continued)

UsetwoM6x12mmscrewsandwashers

to connect the

included grounding cable

fromtherackenclosuretothe

extensionframe.

Reversestep2-2toattachthereardoorstotheextensionframe.

Attachthegroundingcableofeachreardoortothegrounding

pointsoftheextensionframeasshown.(Usethescrewsand

washersremovedinstep2-1.)

(For25Uenclosures,skipthisstep.)UsefourM5x20mm

screws and washers

tosecuretheframetotherearoftherack

enclosure.

2-5

2-6

2-7

2-8

2-9

Removetherackenclosure’scablemanagementrailsandreinstall

theminsidetheextensionframe.(ExtraM4x8mmscrewsand

washers

areincludedforyourconvenience.)

Warranty Registration

Visitwww.tripplite.com/warrantytodaytoregisterthewarrantyforyournewTrippLiteproduct.You’llbeautomaticallyenteredintoadrawingfor

achancetowinaFREETrippLiteproduct!Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.

TrippLitehasapolicyofcontinuousimprovement.Specicationsaresubjecttochangewithoutnotice.

MadeinChina.

2 – Frame Attachment (continued)

2-9

1111W.35thStreet,Chicago,IL60609USA

(773)869-1234•www.tripplite.com

20080808193-2828

Tripp Lite SREXTENDER User manual

Brand: Tripp Lite

Model: SREXTENDER

Category: Racks

Type: User manual

Download PDF

report

Tripp Lite SREXTENDER User manual

Tripp Lite SREXTENDER User manual

Related papers

Other documents