York VRF Heat Pump Outdoor Units 460V Installation guide

Type
Installation guide

This manual is also suitable for

1
1. Applicable Unit
Model: PN-TP20R
This protection net is to protect the outdoor unit heat exchanger from external damages such as being hit
by a ball. Install it following the instructions below.
NOTICE:
The applicable outdoor unit may be different depending on the product series. Be sure to conrm with the
product catalog before installation.
Name Protection Net (for Side Installation)
Model PN-TP20R
Required Qty. 1 2
Applicable Outdoor Unit
(Representative Model)
(H,Y)VAHP072B32S
(H,Y)VAHP072B42S
(H,Y)VAHP096 - 192B32S
(H,Y)VAHP096 - 192B42S
2. Installation Work
(1) Be sure to securely tighten the protection net with the supplied screws (accessories).
If the screws are not securely tightened, it may cause vibration or abnormal sound.
If they are over-tightened, the screw threads may be stripped. When tightening the screws, make sure
to follow the tightening torque below.
● Tightening Torque: 1.5+0.4 ft
lbs (2.0+0.5 N
m)
(2) Secure enough service space with consideration for attaching/detaching the protection net.
● Service Space with Protection Net: Service Space for Outdoor Unit + Min. 5-7/8 inch (150mm)
(3) Do not step on the protection net or the outdoor unit to prevent falls and injury.
(4) Fallen leaves or other debris may be caught by the protection net and cause airow restrictions. Be
sure to check for accumulation and clean the protection net periodically.
(5) The protection net may accumulate ice or snow during cold weather.
NOTICE:
Do not use the snow protection hood for the side inlet if the protection net is installed.
IMPORTANT NOTICE:
Read and understand this manual before using this protection net.
Perform the test run after installation to check for abnormalities.
Forward this information to the building owner and request that they maintain all the equipment manuals.
Signal words are used to identify levels of hazard seriousness.
Denitions for identifying hazard levels are provided below with their respective signal words.
: Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
Installation Manual for Protection Net
(for Side Installation of Outdoor Unit)
2
Unit: inch (mm)
No. Accessory
Qty.
Remarks
PN-TP20R
1
Protection Net
(for Side
Installation)
46-9/1
6
(1183)
24-3/16
(614)
1
2
Screw
M5 x 1/2L (12L)
(with Washer)
1
3
Self-Tapping
Screw
M4 x 1/2L (13L)
(without Washer)
1
3. Before Installation
Check that all the following accessories are packed with the unit before installation.
3
4. Installation Procedures
Before installation, conrm the outdoor unit model. If the protection net is available for your model, follow
the installation procedures.
(1) Remove the inlet grille (for right side) from the unit. (Removed Screws: Qty. six)
Open a hole at the location shown below using the self-tapping screw
3
.
(2) Insert the screw (accessory)
2
to the opened hole in step (1) but do not tighten. Loosen but do not
remove one screw attached at the top of the outdoor unit right side. Hook the protection net (for side
installation)
1
over the top. Securely tighten the six screws removed from step (1). Finally, tighten the
top two screws completely.
NOTE:
Same procedure is applied when the protection net is used for left side installation.
(Applicable Model: (H,Y)VAHP096 - 192B32S and
(H,Y)VAHP096 - 192B42S)
Attachment Screw
Attachment Screw
2
2
1
Outdoor Unit
Outdoor Unit
Securing Screw
[For Right Side
Installation]
(for Side Installation)
Protection Net
51-5/8
(1311)
51-5/8
(1311)
7-1/2
(191)
7-1/2
(191)
Screw for Inlet GrilleScrew for Inlet Grille
Outdoor Unit
Outdoor Unit
Outdoor Unit
Bottom Base
Inlet Grille
Inlet Grille
Inlet Grille
Front Side
Front Side
Rear Side
Rear Side
Open a hole
[For Right Side Installation]
[For Left Side Installation]
(H,Y)VAHP096 - 192B32S
(H,Y)VAHP096 - 192B42S
Open a hole
Heat Exchanger
Procedure for Removing Inlet Grille
5. Installation Appearance
Outdoor Unit
[for Rear Side
Installation]
Protection Net
[for Left Side
Installation]
Protection Net
Attachment
Screws
Attachment
Screws
Securing
Screw
(Accessory)
Unit: inch (mm)
Right Side Rear Side Left Side
[for Side
Installation]
Protection Net
3-15/16
(100)
3-15/16
(100)
3-15/16
(100)
66-5/16
(1685)
30-1/8
(765)
Available Combinations
Applicable Outdoor Unit
(Representative Model)
Model
(H,Y)VAHP072B32S
(H,Y)VAHP072B42S
(H,Y)VAHP096 - 144B32S
(H,Y)VAHP096 - 144B42S
(H,Y)VAHP168, 192B32S
(H,Y)VAHP168, 192B42S
Protection Net for Rear Side PN-TP20BA PN-TP20BB PN-TP20BC
Protection Net for Left Side PN-TP20L PN-TP20R
Protection Net for Right Side PN-TP20R
NOTICE:
This manual applies only to the combination indicated with .
For other protection net options, refer to each model’s installation manual.
Install the required protection net only if all installation requirements can be met.
The following examples illustrate a small cabinet.
© 2017 Johnson Controls, Inc.
P5416969
Code No. LIT-12012434
Issued February 2017
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

York VRF Heat Pump Outdoor Units 460V Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI