Mustek A3F2400N User guide

A3F1200N/A3F2400N

High Speed Document Scanner

[For Windows & Mac]

USER GUIDE

English

V1.8

All trademarks

are the property

of their respective

owners and all rights

are acknowledged.

Images and screenshots

shown inside this User

Guide are example only,

which may vary according

to the devices used and its

operating system.

All contents and specifications of

this User Guide are subject to change

without notice.

2

SAFETY AND PRECAUTIONS

General Precautions

•

Keep away from water or moisture and dusty areas.

•

Never store in hot and very cold areas.

•

Only use attachments/accessories specified by the manufacturer.

•

No objects filled with liquids, such as vases, shall be placed on the Scanner.

•

Avoid dust contamination when the Scanner is not in use.

•

When left unused for a long period of time, unplug the Scanner from the computer.

•

Avoid environments where the Scanner would be exposed to direct sunlight (or any other source of excessive heat) for long periods of time.

•

Protect the Scanner from potential liquid spills such as soda, coffee, tea, and etc.

•

Be carefully to keep it without dropping it or strong impact.

•

Operate the Scanner on a level, well-grounded work surface, free of excessive vibration.

•

Do not open the Scanner case alone without technical support because there is danger of electrical shock.

•

Position the Scanner near the computer where it can be easily accessed when plugged in.

Environmental Information

Discarded electrical and electronic appliances are recyclable and should separate from the household waste. Please actively support in

conserving resources and protecting the environment by returning this appliance to the collection centers (if available).

3

CONTENTS

SAFETY AND PRECAUTIONS ..................................................................2

CONTENTS ..............................................................................................3

UNPACKING THE SCANNER ...................................................................4

BUNDLED DRIVERS AND SOFTWARE ....................................................5

SYSTEM REQUIREMENTS ......................................................................6

SCANNER PARTS ....................................................................................7

INSTALLING DRIVERS AND SOFTWARE ................................................8

How to Uninstall the Drivers and Software ..............................................9

Showing/Hiding Tooltips .........................................................................9

Turning Power Off .................................................................................10

CONNECTING THE SCANNER ...............................................................10

How to Remove the Scanner Lid ....................................................11

PLACING THE ORIGINALS ....................................................................11

Setting iDocScan Touch and Buttons ....................................................12

SCANNING PROCEDURES IN WINDOWS ............................................12

Scanning Using iDocScan Touch and Buttons ......................................18

Setting iDocScan Touch (Advanced Scan) ............................................19

Destination Tab ...............................................................................19

Scan Settings Tab ...........................................................................22

Scanning in Advanced Scan Mode ........................................................28

Preview Window Controls .....................................................................30

Continue to Scan More Pages ...............................................................31

Delete the Backup Files .........................................................................31

Cancel a Scan ........................................................................................31

SCANNING PROCEDURES IN MAC .......................................................32

Setting ScanMust and Buttons ..............................................................32

Scanning Using ScanMust and Buttons ................................................36

Continue to Scan More Pages ...............................................................37

Cancel a Scan ........................................................................................38

Delete the Backup Files .........................................................................38

SCANNING USING TWAIN INTERFACE IN WINDOWS ..........................39

Acquire the Scanner TWAIN Interface ..................................................39

The TWAIN Interface .............................................................................40

The Main Tab.........................................................................................41

The Enhance Tab ...................................................................................42

The Filters Tab .......................................................................................44

The Preview Window and Controls .......................................................44

Prescan the Image ................................................................................45

Set Up the Scan Parameters .................................................................45

Execute the Scan Command .................................................................46

Using Batch Scan .................................................................................46

The Batch Scan Dialog Box ...................................................................46

SCANNING USING TWAIN INTERFACE IN MAC ....................................48

Acquire the Scanner TWAIN Interface ...................................................48

The TWAIN Interface .............................................................................49

The Main Tab.........................................................................................49

The Enhance Tab ...................................................................................50

The Filters Tab .......................................................................................50

The Preview Window ............................................................................51

Prescan the Image ................................................................................51

Set Up the Scan Parameters .................................................................51

Execute the Scan Command .................................................................52

Using Batch Scan .................................................................................52

The Batch Scan Dialog Box ...................................................................53

CLEANING THE SCANNER ....................................................................54

TROUBLESHOOTING ............................................................................55

SPECIFICATIONS ..................................................................................56

4

UNPACKING THE SCANNER

Make sure following items are included in this package.

Scanner

AC Adapter

(see Connecting the Scanner)

Power Adapter

(see Connecting the Scanner)

Installation DVD

(see Installing Drivers and

Software)

Quick Start Guide

5

BUNDLED DRIVERS AND SOFTWARE

YOU MUST FIRST INSTALL SCANNER DRIVER IN ORDER TO USE THE

SCANNER ON YOUR COMPUTER.

[Windows]

1.

Scanner Driver - Scanner Driver includes following:

a. TWAIN and WIA driver: it comes with TWAIN interface to use the

Scanner from within any WIA or TWAIN-compliant host software

applications such as Presto! PageManager, Photoshop.

b. iDocScan Touch: it is consisted of 5 Scan-to functions, including

Scan to Folder, Scan to PDF, Scan to Application (Default: E-Mail),

Scan to Cloud, and Scan to Print destinations, and Advanced

Scan with a Preview Window for displaying the prescanned

image.

c. Help files: this includes detailed instructions of iDocScan Touch

and of the TWAIN interface.

d. Clean Calibration: Run this tool to clear the calibration data left

from the previous scanner, when you use another same model

scanner on the same computer with a previous driver.

2.

Presto! PageManager - this application is a document management

application designed to assist in scanning, sharing and organizing

documents and files. For the detailed information of this

application, see the “help” file integrated within this application.

3.

ABBYY FineReader - this application converts scanned text

into searchable text when using the PDF function. For detailed

information of this application, see the “Help” file integrated within

this application.

4.

Adobe Acrobat Reader - this application opens the scanned image

that is converted into a PDF format using the PDF function.

[Mac]

1.

ImageAcquire - this TWAIN-compliant application serves as a host

application that enables image scanning via the TWAIN interface.

For detailed instructions of ImageAcquire, see the PDF file inside

the ImageAcquire folder.

2.

Scanner Driver - it comes with TWAIN interface to use the

Scanner from within any TWAIN-compliant host application such

as ImageAcquire, Photoshop. Refer to the PDF file inside the

Scanner Driver folder for detailed instructions of TWAIN interface.

3.

ScanMust - this application allows you to easily scan from

the Scanner buttons or within this software. For the detailed

instructions of ScanMust, see the “Help” file integrated within this

software.

6

SYSTEM REQUIREMENTS

Following minimum system requirements are recommended to achieve the best performance from the Scanner.

Windows Mac

Processor Intel Core Duo or faster Intel Core Duo or faster

Support OS Windows XP (Service Pack 3) / Vista / 7 / 8 / 8.1 /10 Mac OS X 10.7 to 10.11 and above

Color Display 1024 x 768 resolution or above 1024 x 768 resolution or above

RAM 4GB RAM or greater 4GB RAM or greater

Free Hard Drive Space 2GB 1GB

Drive DVD-ROM Drive for software installation DVD-ROM Drive for software installation

Interface Available USB port Available USB port

NOTE

The scanning speed and performance are determined by the specifications of your computer. The higher specification of your computer, the better

the Scanner will be performed.

7

SCANNER PARTS

Rear Side

1

2

3

4

5

6

7

8 9

1

Scanner Lid Opens to reveal the Flatbed Glass.

2

Flatbed Glass Used to scan single pages or book pages.

3

Power LED

(Blue)

Indicates the scanner is on and ready for use.

4

Power Button Turns the power on or off.

5

Scan Scan directly to the selected folder.

6

PDF Scan directly to the PDF file format.

7

PANEL

Scan directly to an application you specified.

for Windows, you can select either email or

application (default: ms paint) as the destination

of your scan.

8

DC IN Port Connect the Power Adapter.

9

USB Port Connect the USB cable to a computer.

8

INSTALLING DRIVERS AND SOFTWARE

PLEASE COMPLETE THE DRIVERS AND SOFTWARE INSTALLATION

BEFORE CONNECTING THE SCANNER. DO NOT CONNECT THE USB

CABLE TO THE SCANNER OR COMPUTER AT THIS MOMENT.

[Windows]

1.

Insert the Installation DVD into the DVD-ROM drive of the

computer. The DVD will run automatically, and then the installation

window appears on the screen as following:

NOTE

If the DVD does not run automatically, locate the drive on the

computer and double click on "AUTORUN.exe" file.

2.

Click “Scanner Driver” from the installation window.

3.

Select a preferred language from the “Choose Setup Language”

list.

4.

Click “Next” when the Welcome screen appears, and then follow

on-screen instructions to complete installation.

5.

Return to the installation window to install other software to your

computer to enable certain functions.

[Mac]

1.

Insert the Installation DVD into the DVD-ROM drive of the Mac.

The Autorun disc icon appears on your desktop.

2.

Double click on the Autorun disc icon.

The content of the disc is displayed in the Autorun folder as

following:

3.

Double click the “Scanner Driver” folder, then “A3FxxxxN.pkg” to

start the installation process.

Follow on screen instructions to complete the installation

procedures.

4.

Return to the Autorun folder. Double click the “ScanMust” folder,

and then “ScanMust Installer.pkg” to start the installation process.

Follow on screen instructions to complete the installation

procedures.

5.

Return to the Autorun folder. Double click the “ImageAcquire”

folder, and then “ImageAcquire.pkg” icon to start the installation

process.

Follow on screen instructions to complete the installation

procedures.

9

INSTALLING DRIVERS AND SOFTWARE (CONTINUED)

How to Uninstall the Drivers and Software

When you need to remove the scanner drivers and software from your

computer, uninstall as following:

[Windows]

1.

Unplug the USB Cable connecting from the computer.

2.

Exit all running applications.

3.

Go to the “Start” menu, select “(All) Programs”,

“A3FxxxxN”, and then click “Uninstall”.

4.

Follow the on-screen instructions to remove the Scanner Driver.

[Mac]

1.

Unplug the USB Cable connecting from the computer.

2.

Exit all running applications.

3.

Insert the Installation DVD.

4.

Double click on the UninstallDriver icon in the Scanner Driver

folder to remove it.

Uninstall Driver

5.

Drag ImageAcquire icon and ScanMust icon from the “Application”

folder to Trash.

Showing/Hiding Tooltips

You can show (default) or hide the tooltips for the iDocScan Touch panel

and the settings page when you are familiar with the instructions.

Tooltips

Right-click on the Scanner icon [ ] from the system tray to bring up

the following menu, then click on Show Tooltips.

The check mark disappears, indicating that the tooltips is hidden.

To show the tooltips again, click on Show Tooltips to check mark it.

10

CONNECTING THE SCANNER

1.

With the

computer

on, connect supplied USB Cable to the

Scanner’s USB Port and the other end to the computer. Then

connect the supplied Power Adapter to the Scanner’s DC IN port,

and plug the other end to a power outlet.

2.

Press and hold <POWER> to turn on the Scanner.

The Power LED lights up in blue.

3.

After a few moments, your computer will automatically detect your

scanner:

(a) Windows computer will detect the Scanner as a Removable Disk

and automatically loads iDocScan Touch [

] in the system tray.

iDocScan Touch icon might be hidden, and require that you click

the arrow in the system tray to reveal it.

(b) Mac computers will automatically launch the ScanMust software

in the menu bar.

NOTE

•

If your Windows computer does not appear the Scanner icon [

]

in the system tray, from the “Start” menu, click “(All) Programs” >

“A3FxxxxN” > “iDocScan Touch(A3FxxxxN)”.

•

If your Mac computer does not appear the Scanner icon [

] in the

menu bar, open “Finder”and then click “Applications”. Find ScanMust

in the Application folder, and then double click on it to open it in the

menu bar.

Turning Power Off

To turn off the power, press and hold <POWER> for a while until the

Power LED turns off.

11

PLACING THE ORIGINALS

1.

Open the Scanner Lid.

2.

Place the original facing down on the Flatbed Glass, and then align

the original at the top right corner.

Position Arrow

Mark

3.

Close the Scanner Lid.

NOTE

•

Do not place heavy items on the Scanner Glass or press on the

Scanner Glass with too much force as this will cause damage to the

glass surface.

•

Do not place any objects which may scratch the glass on the scanner.

How to Remove the Scanner Lid

If you are scanning books or other thick documents, you can remove

the Scanner Lid as following steps:

1.

Lift the Scanner Lid straight up.

2.

Pull the Scanner Lid away from the Scanner.

3.

Place the bound original on the Flatbed Glass.

Gently press the bound original from above to make it flat, but do

not press it too hard.

Mounting Posts

12

SCANNING PROCEDURES IN WINDOWS

Setting iDocScan Touch and Buttons

You can setup the scanner buttons to perform certain actions within the

iDocScan Touch software.

1.

Click the Scanner icon [

] from the system tray to bring up the

iDocScan Touch panel.

2.

Click [ ] (Settings) by the following 5 scan to functions to open

the Settings dialog box.

Scan to Folder Settings

Scan to PDF Settings

Scan to Application Settings

Scan to Cloud Settings

Scan to Print Settings

3.

The Settings window appears. You can change the settings as

following:

Scan to Folder Settings

Scan to PDF Settings

A

B

C

D

Scan to Application Settings

Scan to Cloud Settings

A

E

F

B

C

D

13

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

Scan to Print Settings

A

G

B

C

D

A. Scan Settings

Scan Mode

Select a mode to scan your originals with following

choices: “Color”, “Gray”, “B/W” .

•

Color: Select it to scan the color photographs,

documents, and items containing colors in full color.

•

Gray: Select it to scan the image in grayscale using

varying shades of gray.

•

B/W:

Select it to scan text-only originals or line drawings.

Scan

Resolution

Select the resolution of the image to be scanned with

following choices: “100dpi”, “200dpi”, “300dpi”,

“600dpi”, “1200dpi”.

•

The higher the resolution, the bigger the file size.

•

“100dpi” is disabled when “OCR (Text Searchable)”

is checked.

Scan Size

Select the output size of the image to be scanned with

following choices: “Auto”, “A3”, “A4”, “B5”, “Letter”

•

Select “Auto” to automatically detect the paper size

and crop scanned image. When scanning darker

originals (i.e. night scenery photos), over-cropping

may occur.

Original Type

Select an option according to the type of original to

auto-adjust overall brightness and contrast for the

scanned image.

•

Document: Originals with mainly text.

•

Photo: Originals with mainly color pictures.

•

Magazine: Originals with both text and color pictures.

B. Improvements and Adjustments

Deskew

Correct the skew image approximately +/-15 degrees.

(The results of Deskew do not appear in the preview

image, only in the scanned image.)

Original

Deskew applied

•

Deskew is enabled when the Scan Size set to “Auto”.

•

Originals with darker backgrounds and dark text are

difficult to deskew. Deskew may not work properly

when deskewing dark images.

•

Deskew can only correct one skew image at a time.

•

This function cannot work with a large skew angle.

14

Descreen

Descreening helps to reduce moire patterns in

magazines or other printed materials. After descreening,

the image may appear blurry.

Example:

Descreen appliedOriginal

NOTE

•

If the “Unsharp Mask” function is enabled, some

moire pattern may not reduce even when the

Descreen is enabled. In such cases, disable the

“Unsharp Mask”.

•

Scanning takes longer than usual when you enable

the Descreen function.

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

Invert

This function reverses the colors of the scanned image

to the opposite colors.

Example of black text with white background to be

inverted:

Original Invert applied

Example of grayscale picture to be inverted:

Original Invert applied

Example of colored picture to be inverted:

Original Invert applied

15

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

Unsharp

Mask

This function helps to emphasize edges in the image

more clearly for an overall sharper image.

Example:

Unsharp Mask appliedOriginal

NOTE

•

The Unsharp Mask may not work properly for poorly

focused or out of focus images.

•

You are recommended to disable the Unsharp Mask

when the moire is not being reduced even with the

“Descreen” function enabled.

Brightness

Use the slider to increase or decrease the value (-127

~ +127) and to adjust the image brighter or darker. You

can view the sample image to the right side of the slider

for the result of the value.

NOTE

Brightness is enabled in “Color” and “Gray” mode, but

not in the B/W mode.

Contrast

Use the slider to increase or decrease the value (-127

~ +127) and to adjust the contrast higher or lower.

The bigger the value is to set towards +127, the more

contrast is between lighter and darker areas. You can

view the sample image to the right side of the slider

for the result of the value.

NOTE

Contrast is enabled in “Color” and “Gray” mode, but not

in the B/W mode.

C. Destination

Save Path

Indicate the folder where image files are saved. Click

Browse to specify a file folder to save the scanned

image.

NOTE

•

You cannot specify folders where root privileges are

required.

File Name

Setting

The filename can be created with a prefix in the Prex

field up to 20 characters, i.e. Scanned000001.jpg

16

File Type

Select a file format to save scanned image with

following choices: “JPEG”, “BMP”,“TIFF (Single-page)”,

“TIFF (Multi-page)”, “PDF (Single-page)”, “PDF (Multi-

page)”.

NOTE

•

PDF (Single-page) and TIFF (Single-page) are used

for splitting the multi-page originals into single files.

•

PDF (Multi-page) and TIFF (Multi-page) are used

for combining multiple scans into one file. The

“Continuous Scanning” dialog will be triggered

automatically for scanning more page.

Compression

When TIFF file is selected in the File Type, the

Compression format is enabled with following

choices:

•

None: No compression is used.

•

LZW: LZW is a compression method that results in

no loss of data. The file size is closer to the actual

size of the color data.

•

JPEG: JPEG is a lossy compression method that

results in some data is lost. This method is best used

to reduce the large file size.

NOTE

•

The Compression is only available in the Color and

Gray mode.

•

TIFF (JPEG compression) is enabled up to 600 dpi.

This option to compress 1200 dpi is not available.

Compression

Quality slider

When JPEG, PDF or TIFF (Compression: JPEG) file

is selected in the File Type, the Compression Quality

slider is enabled. Use the slider to compress a file to

reduce the total size in High, Medium, or Low. The

higher the compression level, the lower the file size,

and vice versa.

NOTE

The Compression Quality is only available in the Color

and Gray mode, but not in the B/W mode.

OCR (Text

Searchable)

This function is checked by default when selecting PDF

(Multi-page) and PDF (Single-page) file in the File

Type. It can recognize and convert your scanned image

into a text based file that can be searched and edited.

OCR

Language

This function is enabled when OCR (Text Searchable) is

selected.

Ensure to select the correct language of the original text

from the drop-down menu to perform text recognition.

Continuous

Scanning

Check this option to trigger the continuous scanning

dialog box after the current page is scanned, allowing

you to continue scanning for more pages. (See

Continue to Scan More pages).

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

17

Delete

Backup File

of Scanned

Image

This function is enabled when Scan to Application

(Email) or Scan to Print is selected.

Check this option to trigger the delete backup file

dialog box after the scanning process completes,

allowing you to delete the backup file (See Delete the

Backup Files).

D. Buttons

Default

Reset the Settings to the default for respective scan-to

function.

Cancel Cancel the changes, and close the Settings window.

OK

Apply the scan-to function with the settings you

changed, and close the Settings window.

E. Application Settings (Available in Scan to Application)

Attach to

E-Mail

Select "Attach to E-Mail" as the destination of your scan.

The system detects and displays the default email client

(e.g. Outlook) on your computer.

NOTE

Make sure an email account has been configured.

Open with

Application

Select "Open with Application" (default: MS Paint) as

the destination of your scan.

To add a new application, click Add and navigate to the

.exe files in the Program folder, then select it to add in

the application list.

To delete the application, select it from the dropdown

menu, then click Delete to remove the application.

NOTE

•

Please make sure the application supports the File

Type selected.

•

The default application (MS Paint) cannot be deleted.

F. Cloud Storage (Available in Scan to Cloud)

Cloud

Storage

Select either "Dropbox" or "Google Drive" from the

dropdown menu as the destination of your scan.

NOTE

•

To use this function, you must have a Dropbox and

a Google Drive account. Dropbox and Google Drive

must be installed on your computer and has been

logged in.

•

If Dropbox or Google Drive shared folder is not

detected, a warning message will appear.

G. Printer (Available in Scan to Print)

Printer

Select an available printer as the destination of your

scan. The system can detect and display the default

printer which is connected to your computer.

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

18

Scanning Using iDocScan Touch and Buttons

1.

Place the original on the Flatbed Glass (see Placing the Originals).

2.

Click a scan-to function from the iDocScan Touch panel to start

scanning to the destination with the Settings you previously

configured (see Setting iDocScan Touch and Buttons).

Scan to PDF

Scan to Application

Scan to Cloud

Scan to Print

Scan to Folder

Alternatively, you can press a button on the Scanner to start

scanning to the destination.

Scan to Folder

Scan to PDF

Scan to Application

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

The “Processing...” bar appears showing the current scan status.

3.

After scanning completes, the scanned image is saved and opened

according to the scan-to function you select as below:

Scan to Folder

The specified folder opens automatically with the scanned image

selected in it.

Scan to PDF

The scanned image is saved in the PDF format and opened

automatically in the Acrobat Reader.

Scan to Application

The scanned image opens automatically in the specified application

(default: Email). The default email application opens up with the

scanned image attached in a blank email.

If you set the Application Settings to “Open with Application”, the

scanned image opens automatically in the specified application

(default: MS Paint).

NOTE

•

Maximum of 20 files can be attached within an email.

•

If the total file size is exceeded the attachment size limit set at

the mail server, the file cannot be sent.

19

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

•

Applications that do not support multi-page scanning will open

and display only the first page of the originals.

•

If the application cannot support the File Type selected, an error

message will appear. Refer to the instructions of the application

for the formats supported.

Scan to Cloud

The scanned image opens automatically in the specified cloud folder

(default: Dropbox). You can specify either Google Drive or Dropbox

in the Settings.

NOTE: To use this function, you must have a Dropbox and a Google

Drive account. Dropbox and Google Drive must be installed on your

computer and has been logged in prior to scanning.

Scan to Print

The computer’s print dialog box opens up with the image in it. Use

the print dialog box to set the available settings of the printer driver

to print the scanned image.

Setting iDocScan Touch (Advanced Scan)

The Advanced Scan is only available by using the iDocScan Touch panel.

It includes a Preview Window with controls and tools. You can preview

the image after you make any changes in the Settings window.

Click Advanced Scan to open the Settings dialog box.

Advanced Scan

The Settings window appears. You can change the settings as following

in the Destination and Scan Settings tabs:

Destination Tab

1

2

3

4

5

6

7

8

9

10

11

12

13

15

14

17

16

20

1

Destination Tab

Click the Destination tab to display the

settings options.

2

Save Path

Indicates the folder where image files are

saved. Click Browse to specify a file folder to

save the scanned image.

NOTE

•

You cannot specify folders where root

privileges are required.

3

File Name Setting

The filename can be created with a prefix

in the Prex field up to 20 characters, i.e.

Scanned000001.jpg.

4

File Type

Select a file format to save scanned image

with following choices: “JPEG”, “BMP”,“TIFF

(Single-page)”, “TIFF (Multi-page)”, “PDF

(Single-page)”, “PDF (Multi-page)”

NOTE

•

PDF (Single-page) and TIFF (Single-

page) are used for splitting the multi-page

originals into single files.

•

PDF (Multi-page) and TIFF (Multi-page) are

used for combining multiple originals into

one file.

SCANNING PROCEDURES IN WINDOWS (CONTINUED)

5

Compression

When TIFF file is selected in the File Type, the

Compression format is enabled with following

choices:

•

None: No compression is used.

•

LZW: LZW is a compression method that

results in no loss of data. The file size is

closer to the actual size of the color data.

•

JPEG: JPEG is a lossy compression

method that results in some data is lost.

This method is best used to reduce the

large file size.

NOTE

•

The Compression is only available in the

Color and Gray mode.

•

TIFF (JPEG compression) is enabled up to

600 dpi. This option to compress 1200 dpi

is not available.

6

Compression

Quality slider

When JPEG, PDF or TIFF (Compression:

JPEG) file is selected in the File Type, the

Compression Quality slider is enabled. Use

the slider to compress a file to reduce the total

size in High, Medium, or Low. The higher the

compression level, the lower the file size, and

vice versa.

NOTE

The Compression Quality is only available in the

Color and Gray mode.

Page is loading ...

Mustek A3F2400N User guide

This manual is also suitable for

Mustek A3F2400N User guide

Related papers

Other documents