Wren Kitchens Drawer Removal/Insertion Guide Assembly Guide

Brand: Wren Kitchens

Model: Drawer Removal/Insertion Guide

Type: Assembly Guide

For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

REMOVAL/

INSERTION

Guide

Page 1 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

Step 2.

In one smooth motion, lift the front of the

drawer, this will disconnect the runner from the

connectors on the base of the drawer.

Once properly separated a click will be heard

and the drawer will be separate from the

runner.

If this motion is not done with enough force

then the drawer may need to be lifted again.

Be careful not to lift the runners whilst

lifting the drawer.

Step 3.

The drawer is free to remove from the unit

Simply remove the loose drawer from the unit,

making sure not to damage the unit in the

process.

Step 1.

Open the drawer that is required to be

removed.

Pull out the drawer until the runners are at full

maximum extension.

DRAWER REMOVAL

CLICK

REMOVAL

Page 2For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

Step 1.

Fully extend the drawer runners out

of the unit. (for the drawer you are

inserting)

Step 3.

Once the drawer is placed onto the runners,

pull forward the protruding lips on the ends

of the runners until a click is heard. Once the

click is heard the drawer is properly located and

secured to the runner.

Push the drawer back into the Unit.

Step 2.

Place the drawer onto the runners, making sure

that the groove of the drawer sides and the

runner mechanism are aligned.

DRAWER INSERTION

CLICK

INSERTION

Page 3 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

SINGLE

Adjustment

Drawer side

xing clip

Drawer

frontal

Drawer

side

DRAWER FRONTAL

ADJUSTMENT

Screw point 1 as shown

to adjust drawer frontal

right & left.

Releasing xing clip. Screw

point 3 whilst applying

downward pressure as

shown to release.

Screw point 2a as

shown to adjust

drawer frontal

up & down.

Tighten 2b

once in position.

View on side of drawer side

Drawer Cover Cap

Fixing clip

Step 2.

Push t drawer side xing clips onto

drawer side.

Step 3.

Fit drawer cover caps over drawer side

adjustment.

Step 1.

Secure drawer side xing clips using

2 x 21mm screws per clip using the

predrilled holes.

99mm

67mm

99mm

67mm

Standard

Drawer

37mm37mm

SINGLE

DRAWER

Page 4For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

DEEP

Adjustment

Drawer

front

Drawer

side

Gallery head

xing clip

Drawer side

xing clip

Drawer Cover Cap

Step 4.

Fit drawer cover caps over drawer side

adjustment.

Fixing clip

Deep Drawer

231mm

99mm

67mm

37mm

67mm

99mm

Step 1.

Secure gallery head xing clips using 1 x 15mm

screw and secure drawer side xing clips using 2 x

21mm screws located with the predrilled holes.

Step 3.

A. Clip gallery rail into the top

corners of the metal back panel.

B. Locate front end of the gallery

rail into the opening of the gallery

head xing clip, which is secured to

the frontal as shown.

Step 2.

Push t drawer xing clips onto drawer sides.

DEEP

DRAWER

View on side of drawer side

DRAWER FRONTAL

ADJUSTMENT

Screw point 1 as shown

to adjust drawer frontal

right & left.

Screw point 2a

as shown to adjust

drawer frontal up &

down.

Tighten

2b once in

position.

Releasing

xing clip.

Screw point

3 whilst

applying

downward

pressure as

shown to

release.

Page 5 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

GLASS DEEP

Deep

drawer

195mm

131mm

99mm

67mm

Fixing

clip

Glass Side

Fixing Clip

Fixing

clip

Glass Side

Fixing Clip

195mm

131mm

99mm

67mm

Step 1.

Secure glass side xing clips

using 2 x 15mm screws.

Secure drawer side xing clips

using 2 x 21mm screws in

pilot holes provided as shown

below.

Step 3.

Fit glass sides with end caps attached.

Use the groove on the front end cap

as a guide to slide into place onto

frontal glass xing clip, and into

metal back as shown.

Fixing

clip

Glass

Clip

Drawer

frontal

Step 2.

Push t drawer side xing

clips onto drawer side.

Fixing

clip

Step 4.

Fit drawer cover caps

over drawer side adjustment.

Drawer

Cover Cap

Screw point 1 as shown to

adjust drawer frontal

right & left.

Drawer Frontal Adjustment

Screw point 2a

as shown to adjust

drawer frontal up & down.

Tighten 2b

once in position.

Releasing xing clip.

Screw point 3 whilst applying

downward pressure as shown

to release.

View on side of drawer side

Drawer

frontal

Drawer

Side

37mm37mm

Rear end clip

release catch,

depress & lift to

remove side.

Page 6For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

GLASS MID

For use with 2 + 1 Internal Unit

Releasing xing clip.

Screw point 3 whilst applying

downward pressure as shown

to release.

Step 1.

Secure gallery head xing clips

using 1 x 15mm screw. Secure

drawer side xing clips using

2 x 21mm screws in pilot holes

provided as shown below.

Step 3.

1. Clip gallery rail into the top corners of metal back

panel.

2. Locate front end of the gallery rail into the

opening of the gallery head xing clip, which is

secured to the frontal as shown.

Step 2.

Push t drawer xing clips

onto drawer side.

Fixing

clip

Drawer

side

Drawer

frontal

Step 4.

Fit Drawer Cover Caps

over drawer side adjustment.

Drawer

Cover Cap

View on side of drawer side

Drawer Frontal Adjustment

Screw point 1 as shown to

adjust drawer frontal

right & left.

Screw point 2a

as shown to adjust

drawer frontal up & down.

Tighten 2b

once in position.

Releasing xing clip.

Screw point 3 whilst

applying downward

pressure as shown to

release.

Drawer

frontal

Gallery head

xing clip

Fixing

clip

Gallery Head

Fixing Clip

Gallery Head

Fixing Clip

Mid

drawer

191mm

99mm

67mm

Fixing

clip

Fixing

clip

191mm

99mm

67mm

37mm37mm

Page 7 For Internal Use: WKIN00312_DRAWER_ADJUSTMENT_REPLACEMENT_Guide_Rev3.indd

DRAWER

Guide

GLASS MID

For use with 2 + 1 Internal

Unit

Step 1.

Secure glass side xing clips

using 2 x 15mm screws, secure

drawer side xing clips using

2 x 21mm screws in pilot holes

provided as shown below.

Step 3.

Fit Glass Sides with End Caps attached.

Use the groove on the front End Cap

as guide to slide into place onto

Frontal Glass Fixing Clip, and into

Metal Back as shown.

Step 2.

Push t drawer xing clips

onto drawer side

Fixing

clip

Glass

Clip

Drawer

frontal

Step 4.

Fit Drawer Cover Caps

over drawer side adjustment.

Drawer

Cover Cap

Rear End Clip

release catch,

depress & lift to

remove side.

Drawer Frontal Adjustment

Screw point 1 as shown to

adjust drawer frontal

right & left.

Screw point 2a

as shown to adjust

drawer frontal up & down.

Tighten 2b

once in position.

Releasing xing clip.

Screw point 3 whilst applying

downward pressure as shown

to release.

View on side of drawer side

3 2a

Drawer

Side

Drawer

frontal

Fixing

clip

Mid

drawer

Middle Drawer

Fixing Clip

Middle Drawer

Fixing Clip

Top Drawer

Fixing Clip

Top Drawer

Fixing Clip

176mm

131mm

99mm

67mm

176mm

131mm

99mm

67mm

37mm

Wren Kitchens Drawer Removal/Insertion Guide Assembly Guide

Wren Kitchens Drawer Removal/Insertion Guide Assembly Guide

Wren Kitchens Drawer Removal/Insertion Guide Assembly Guide

Related papers

Other documents