Reese 118368 Installation guide

Reese
Brand
Reese
Model
118368
Type
Installation guide

This manual is also suitable for

Reese 118368† is a trailer wiring harness adapter that allows you to connect your trailer's electrical system to your vehicle's electrical system. It is designed to provide power and lighting to your trailer, and it is rated for 7.5 amps per circuit. This adapter is easy to install, and it comes with a protective cap to keep the connector clean when not in use. With this adapter, you can easily tow your trailer and enjoy the convenience of having all of your trailer's electrical systems functioning properly.

Reese 118368† is a trailer wiring harness adapter that allows you to connect your trailer's electrical system to your vehicle's electrical system. It is designed to provide power and lighting to your trailer, and it is rated for 7.5 amps per circuit. This adapter is easy to install, and it comes with a protective cap to keep the connector clean when not in use. With this adapter, you can easily tow your trailer and enjoy the convenience of having all of your trailer's electrical systems functioning properly.

ENGLISH
1. Locate the tow vehicle’s trailer harness
connector. This harness is located under the
vehicle, behind the bumper, on the driver’s
side of the vehicle.
2. Remove protective cap B (and save) from
connector A; check to see that the mating
surfaces of the connectors are free of dirt.
Clean if necessary.
3. Connect the T-connector adapter end C to
the vehicle’s connector A. Be sure that the
T-connector is fully inserted with locking
tabs in place.
4. Test the installation with a test light or
trailer.
This unit is rated for 7.5 amps per circuit.
ESPAÑOL
1. Localice el cableado para conexión de
remolque que se encuentra en el vehículo
remolcador. Este cableado se encuentra
debajo del vehículo, detrás de la defensa
trasera, en el lado del conductor del vehícu-
lo.
2. Quite la tapa de protección B (guárdela)
del conector A; revised las superficies de
unión de dichos conectores y asegúrese de
que estén libres de polvo o barro. Límpielos
si es necesario.
3. Conecte el terminal adaptador C del
conector en T al conector A del vehículo.
Asegúrese de que el conector en T esté
insertado totalmente y de que las orejetas
de seguridad estén en su lugar.
4. Pruebe la instalación usando una luz de
prueba o remolque.
Esta unidad es clasificada para 7.5 ampe-
rios por el circuito.
FRANÇAIS
1. Localisez le connecteur du faisceau à
remorquage du véhicule remorqueur. Ce
faisceau se trouve en dessous du véhicule,
derrière le pare-chocs arrière, du
côté
conducteur.
2. Retirez le capuchon protecteur B
(gardez-le) du connecteur A. Vérifiez que
les surfaces homologues des connecteurs
ne sont pas sales; nettoyez-les si néces-
saire.
3. Branchez l’extrémité C du connecteur en
T au connecteur A du véhicule. Assurez-
vous que le connecteur en T soit bien inséré
et que les languettes de retenue soient en
place.
4. Testez l’installation en utilisant une lampe
d’essai ou une remorque.
Celle inité est évaluéé pour 7.5 ampères par
circuit.
Installation instructions
Instructions d’installation
Instrucciones de instalación
18368-037 1/17/01
  • Page 1 1

Reese 118368 Installation guide

Reese
Brand
Reese
Model
118368
Type
Installation guide
This manual is also suitable for

Reese 118368† is a trailer wiring harness adapter that allows you to connect your trailer's electrical system to your vehicle's electrical system. It is designed to provide power and lighting to your trailer, and it is rated for 7.5 amps per circuit. This adapter is easy to install, and it comes with a protective cap to keep the connector clean when not in use. With this adapter, you can easily tow your trailer and enjoy the convenience of having all of your trailer's electrical systems functioning properly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents