Toro Workman MDX Utility Vehicle User manual

Form No. 08160SL Rev E

Workman

®

MD & MDX

Original Instructions (EN)

Revision History

Revision

Date

Description

--

2008

Initial Issue.

A

2011

Updated Engine chapter.

B

2014

Updated Drive Train chapter.

C

02/2018

Updated engine RPM. Updated Electrical, Chassis and Electrical

Drawing chapters. Added revision history.

D

03/2019

Updated Chassis chapter.

E

04/2020

Updated Engine, Electrical, Chassis and Electrical Drawing chapters.

This document and all information contained herein is the sole property of The Toro Company (and/or its affiliated companies). No

intellectual property rights are granted by the delivery of this document or the disclosure of its content. This document shall not be

reproduced by a third party without the express written consent of The Toro Company (and/or the appropriate affiliated company).

Reader Comments

The Toro Company Technical Assistance Center maintains a continuous effort to improve the quality

and usefulness of its publications. To do this effectively, we encourage user feedback.

Please comment on the completeness, accuracy, organization, usability, and readability of this manual

by an e-mail to [email protected]

or Mail to:

Technical Publication Manager, Commercial

The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Phone: +1 952-887-8495

NOTES _

Part No. 08160SL (Rev.E)

Service Manual

Workman

R

MD&MDX

Preface

The purpose of this publication is to provide the service

technician with information for troubleshooting, testing

and repair of major systems and components on the

Workman MD and Workman MDX.

REFER TO THE OPERATOR’S MANUAL FOR OPER-

ATING, MAINTENANCE AND ADJUSTMENT IN-

STRUCTIONS. For reference, insert a copy of the

Operator’s Manual and Parts Catalog for your machine

into Chapter 2 of this service manual. Additional copies

of the Operator’s Manual and Parts Catalog are avail-

able on the internet at www .Toro.com.

The Toro Company reserves the right to change product

specifications or this publication without notice.

This safety symbol means DANGER, W ARNING,

or CAUTION, PERSONAL SAFETY INSTRUC-

TION. When you see this symbol, carefully read

the instructions that follow. Failure to obey the

instructions may result in personal injury.

NOTE: A NOTE will give general information about the

correct operation, maintenance, service, testing or re-

pair of the machine.

IMPORTANT: The IMPORTANT notice will give im -

portant instructions which must be followed to pre-

vent damage to systems or components on the

machine.

E The Toro Company -- 2008, 2011, 2014, 2018, 2019, 2020

Workman MD/MDX

This page is intentionally blank.

Workman MD/MDX

Table Of Contents

Chapter 1 -- Safety

Safety Instructions 1 -- 2..........................

Jacking and Other Instructions 1 -- 4...............

Safety and Instruction Decals 1 -- 6................

Chapter 2 -- Product Records and Maintenance

Product Records 2 -- 1...........................

Maintenance 2 -- 1...............................

Equivalents and Conversions 2 -- 2................

Torque Specifications 2 -- 3.......................

Chap ter 3 -- Briggs & Stratton Gasoline Engine

General Information 3 -- 2........................

Specifications 3 -- 3..............................

Adjustments 3 -- 4...............................

Service and Repairs 3 -- 5........................

Briggs and Stratton Repair Manual for 4--Cycle, V--T win

Cylinder , OHV Head Engines

Chap ter 4 -- Single Cylinder Gasoline Engine

General Information 4 -- 2........................

Specifications 4 -- 3..............................

Adjustments 4 -- 4...............................

Service and Repairs 4 -- 7........................

Kohler Service Manual for COMMAND PRO CS Series

Engines

Chapter 5 -- Drive Train

General Information 5 -- 1........................

Specifications 5 -- 2..............................

Drive Train Operation 5 -- 3.......................

Special Tools 5 -- 6..............................

Adjustments 5 -- 7...............................

Service and Repairs 5 -- 10.......................

Chapter 6 -- Electrical System

General Information 6 -- 2........................

Electrical Schematics 6 -- 2.......................

Special Tools 6 -- 3..............................

T roubleshooting 6 -- 5............................

Electrical System Quick Checks 6 -- 7..............

Component Testing 6 -- 8.........................

Service and Repairs 6 -- 20.......................

ADVANCED MOTORS & DRIVES STARTER/

GENERATOR TROUBLESHOOTING GUIDE

Chapter 7 -- Chassis

General Information 7 -- 1........................

Specifications 7 -- 2..............................

Special Tools 7 -- 2..............................

T roubleshooting 7 -- 3............................

Adjustments 7 -- 6...............................

Service and Repairs 7 -- 9........................

Chapter 8 -- Electrical Drawings

Electrical Schematics 8 -- 3.......................

Circuit Diagrams 8 -- 8...........................

Electrical Harness Drawings 8 -- 10................

SafetyProduct Records

and Maintenance

Briggs & Stratton

Gasoline Engine

Drive TrainElectrical

System

Electrical

Drawings

Chassis

Single Cylinder

Gasoline Engine

Workman MD/MDX

This page is intentionally blank.

Workman MD/MDX Page 1 -- 1 Safety

Chapter 1

Safety

Table of Contents

SAFETY INSTRUCTIONS 2......................

Supervisor’s Responsibilities 2.................

Before Operating 2............................

While Operating 3.............................

Maintenance and Service 3....................

JACKING AND OTHER INSTRUCTIONS 4.........

Jack Vehicle 4................................

Transport Vehicle 4...........................

Tow Vehicle 4................................

Transaxle Neutral Position 5....................

SAFETY AND INSTRUCTION DECALS 6..........

Safety

Workman MD/MDXPage 1 -- 2Safety

Safety Instructions

The Workman MD and MDX s eries vehicles are de-

signed and tested to offer safe service when operated

and maintained properly. Although hazard control and

accident prevention partially are dependent upon the

design and configuration of the machine, these factors

are also dependent upon the awareness, concern and

proper training of the personnel involved in the opera-

tion, transport, maintenance and storage of the ma-

chine. Improper use or maintenance of the machine can

result in injury or death.

Read and understand the contents of the Operator’s

Manual before s tarting and operating the machine. Be-

come familiar with all controls and know how to stop it

quickly. Additional copies of the Operator’s Manual are

available on the internet at www.Toro.com.

The safety alert symbol means

CAUTION, WARNING or DANGER —

“personal safety instruction”. Read

and understand the instruction because it has to

do with safety. Failure to comply with the instruc-

tion may result in personal injury.

WARNING

To reduce the potential for injury or death, comply

with the following safety instructions.

WARNING

The Workman is an off--highway vehicle only. It is

not designed, equipped or manufactured for use

on public streets, roads or highways.

Supervisor’s Responsibilities

1. Make sure operators are thoroughly trained and fa-

miliar with the Operator’s Manual and all labels on the

vehicle.

2. Be sure to establish your own special procedures

and work rules for unusual operating conditions (e.g.

slopes too steep for vehicle operation).

Before Operating

1. Read and understand the contents of the Operator’s

Manual and Operator’s DVD before starting and operat-

ing the vehicle. Become familiar with the controls and

know how to stop the vehicle and engine quickly. Addi-

tional copies of the Operator’s Manual are available on

the internet at www.Toro.com.

2. Keep all shields, safety devices and decals in place.

If a shield, safety device or decal is defective, illegible or

damaged, repair or replace it before operating the ve-

hicle. Also, tighten any loose nuts, bolts or screws to en-

sure vehicle is in safe operating condition.

3. Since fuel used in Workman vehicles is highly flam-

mable, handle it carefully:

A. Store fuel in containers specifically designed for

this purpose.

B. Do not remove vehicle fuel tank cap while engine

is hot or running.

C. Do not smoke while handling fuel.

D. Fill fuel tank outdoors and only to within an inch of

the top of the tank, not the filler neck. Do not overfill

the fuel tank.

E. Clean up any spilled fuel.

Rev. B

Workman MD/MDX Page 1 -- 3 Safety

While Operating

1. Sit on the operator seat when starting and operating

the vehicle.

2. Before starting the engine:

A. Sit on operator’s seat and apply the parking

brake.

B. Turn ignition key to ON.

C. Depress accelerator pedal to start engine and en-

gage drive system.

3. Do not run engine in a confined area without ade-

quate ventilation. Exhaust fumes are hazardous and

could possibly be deadly.

4. Do not touch engine, muffler or exhaust pipe while

engine is running or soon after it is stopped. These areas

could be hot enough to cause burns.

5. Before getting off the seat:

A. Stop movement of the vehicle.

B. Turn ignition key to OFF and wait for all move-

ment to stop.

C. Remove key from ignition switch.

D. Apply parking brake.

E. Do not park on slopes unless wheels are chocked

or blocked.

Maintenance and Service

1. Before servicing or making adjustments, turn all ac-

cessories off, release pressure from accelerator pedal,

allow engine to stop, set parking brake and remove key

from the ignition switch.

2. Make sure vehicle is in safe operating condition by

keeping all nuts, bolts and screws tight.

3. Never store the vehicle or fuel container inside

where there is an open flame, such as near a water heat-

er or furnace.

4. If major repairs are ever needed or assistance is de-

sired, contact an Authorized Toro Distributor.

5. To reduce potential fire hazard, keep engine area

free of excessive grease, grass, leaves and dirt.

6. If engine must be running to perform maintenance or

an adjustment, keep clothing, hands, feet and other

parts of the body away from moving parts. Keep by-

standers away.

7. Do not overspeed the engine by changing governor

setting. To assure safety and accuracy, check maximum

engine speed.

8. Shut engine off before checking or adding oil to the

engine crankcase.

9. Disconnect battery before servicing the vehicle. Dis-

connect negative (--) battery cable first and positive (+)

cable last. If battery voltage is required for troubleshoot-

ing o r test procedures, temporarily connect the battery.

Reconnect positive (+) cable first and negative (--) cable

last.

10.Battery acid is poisonous and can cause burns.

Avoid contact with skin, eyes and clothing. Protect your

face, eyes and clothing when working with a battery.

11.Battery gases can explode. Keep cigarettes, sparks

and flames away from the battery.

12.To assure optimum performance and continued

safety of the vehicle, use genuine Toro replacement

parts and accessories. Replacement parts and acces-

sories made by other manufacturers may result in non-

conformance with safety standards, and the warranty

may be voided.

13.When r aising the vehicle to change tires or to per-

form other service, use correct blocks, hoists and jacks.

Make sure vehicle is parked on a solid level surface such

as a concrete floor. Prior to raising the vehicle, remove

any att achments that may interfere with the safe and

proper raising of the vehicle. Always chock or block

wheels. Use appropriate jack stands to support the

raised vehicle. If the vehicle is not properly supported by

jack stands, the vehicle may move or fall, which may re-

sult in personal injury (see Jacking Instructions in this

section).

14.Make sure to dispose of potentially harmful waste

(e.g. f uel, oil, engine coolant, filters, battery) in an envir-

onmentally safe manner. Follow all local codes and reg-

ulations when recycling or disposing of waste.

Safety

Workman MD/MDXPage 1 -- 4Safety

Jacking and Other Instructions

Jack Vehicle

DANGER

POTENTIAL HAZARD

• A vehicle that is not properly supported

may become unstable.

WHAT CAN HAPPEN

• The vehicle may move or fall. Personal

injury or damage to the machine may result.

HOW TO AVOID THE HAZARD

• Make sure vehicle is parked on a solid level

surface, such as a concrete floor.

• Make sure engine is off and key is removed

from the ignition switch before getting off

the vehicle.

• Before raising the vehicle, remove any

attachments that may interfere with the safe

and proper raising of the vehicle.

• Always chock or block wheels to prevent

the vehicle from rolling.

• Do not start vehicle while it is on jack

stands without placing transaxle in neutral.

• Make sure proper hoists, jacks and jack

stands are used to raise and support t he

vehicle.

Jacking Locations

1. Jack front of the vehicle on the front of the frame and

behind the towing tongue (Fig. 1).

2. Jack rear of the vehicle under each rear axle tube. Do

not jack vehicle below the transaxle case (Fig. 2).

1. Front frame 2. Towing tongue

Figure 1

1

2

1. Transaxle case 2. Axle tube

Figure 2

2

1

Transport Vehicle

When moving the vehicle long distances, use a trailer or

flatbed truck. Make sure vehicle is secured to the trailer

properly. Refer to Operator’s Manual for transport infor-

mation.

Tow Vehicle

IMPORTANT: Frequent or long distance towing of

the Workman is not recommended.

In case of emergency, the vehicle can be towed for a

short distance. Refer to Operator’s Manual for towing

information.

IMPORTANT: If vehicle is towed, make sure that

ignition switch is in the OFF position and key is re-

moved from switch.

Workman MD/MDX Page 1 -- 5 Safety

Transaxle Neutral Position

When performing routine maintenance and/or engine

testing, the transaxle must be shifted into the neutral

position.

1. Park machine on a level surface, stop engine, set

parking brake and remove key from the ignition switch.

2. Move shift lever to the neutral position (Fig. 3).

3. Make sure transaxle is in the neutral position by ro-

tating the driven clutch. The tires should not rotate. If tire

rotation does occur, see Adjust Shift Cables in the Ad-

justment section of Chapter 5 -- Drive Train.

1. Shift lever (in neutral)

2. Forward position

3. Reverse position

Figure 3

1

3

2

Safety

Workman MD/MDXPage 1 -- 6Safety

Safety and Instruction Decals

Numerous safety and instruction decals are affixed to

your Workman. If any decal becomes illegible or dam-

aged, install a new decal. Part numbers are listed in the

Parts Catalog. Order replacement decals from your Au-

thorized Toro Distributor.

Workman MD/MDX Page 2 -- 1 Product Records and Maintenance

Chapter 2

Product Records and Maintenance

Table of Contents

PRODUCT RECORDS 1.........................

MAINTENANCE 1...............................

EQUIVALENTS AND CONVERSIONS 2...........

Decimal and Millimeter Equivalents 2............

U.S. to Metric Conversions 2...................

TORQUE SPECIFICATIONS 3....................

Fastener Identification 3.......................

Standard Torque for Dry, Zinc Plated and

Steel Fasteners (Inch Series). 4...............

Standard Torque for Dry, Zinc Plated and

Steel Fasteners (Metric Fasteners). 5..........

Other Torque Specifications 6..................

Conversion Factors 6..........................

Product Records

Insert Operator’s Manual and Parts Catalog for your

Workman at the end of this chapter. Additionally, if any

optional equipment or accessories have been installed

to your machine, insert the Installation Instructions, Op-

erator’s Manuals and Parts Catalogs for those options

at the end of this chapter.

Maintenance

Maintenance procedures and recommended service in-

tervals for your Workman are covered in the Operator’s

Manual. Refer to that publication when performing regu-

lar equipment maintenance.

Product Records

and Maintenance

0.09375

Workman MD/MDXPage 2 -- 2Product Records and Maintenance

Equivalents and Conversions

Workman MD/MDX Page 2 -- 3 Product Records and Maintenance

Torque Specifications

Recommended fastener torque values are listed in the

following tables. For critical applications, as determined

by Toro, either the recommended torque or a torque that

is unique to the application is c learly identified and spe-

cified in this Service Manual.

These Torque Specifications for the installation and

tightening of fasteners shall apply to all fasteners which

do not have a specific requirement identified in this Ser-

vice Manual. The following factors shall be considered

when applying torque: cleanliness of the fastener, use

of a thread sealant (e.g. Loctite), degree of lubrication

on the fastener, presence of a prevailing torque feature,

hardness of the surface underneath the fastener’s head

or similar condition which affects the installation.

As noted in the following tables, torque values should be

reduced by 25% for lubricated fasteners to achieve

the s imilar stress as a dry fastener. Torque values may

also have to be reduced when the fastener is threaded

into aluminum or brass. The s pecific torque value

should be determined based on the aluminum or brass

material strength, fastener size, length of thread en-

gagement, etc.

The standard method of verifying torque shall be per-

formed by marking a line on the fastener (head or nut)

and mating part, then back off fastener 1/4 of a turn.

Measure the torque required to tighten the fastener until

the lines match up.

Fastener Identification

Figure 1

Grade 1 Grade 5 Grade 8

Inch Series Bolts and Screws

Figure 2

Class 8.8 Class 10.9

Metric Bolts and Screws

Product Records

and Maintenance

Workman MD/MDXPage 2 -- 4Product Records and Maintenance

Standard Torque for Dry, Zinc Plated and Steel Fasteners (Inch Series)

Thread Size

Grade 1, 5 &

8withThin

Height Nuts

SAE Grade 1 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 2 or Stronger Nuts)

SAE Grade 5 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 2 or Stronger Nuts)

SAE Grade 8 Bolts, Screws, Studs &

Sems with Regular Height Nuts

(SAE J995 Grade 5 or Stronger Nuts)

in--lb in--lb N--cm in--lb N--cm in--lb N--cm

# 6 -- 32 UNC

1

0

+

2

1

3

+

2

1

4

7

+

2

3

15 + 2 170 + 20 23 + 2 260 + 20

# 6 -- 40 UNF

10 + 2 13 + 2 147 + 23

17 + 2 190 + 20 25 + 2 280 + 20

# 8 -- 32 UNC

1

3

+

2

5

+

5

2

8

2

+

3

0

29 + 3 330 + 30 41 + 4 460 + 45

# 8 -- 36 UNF

13 + 2 25 + 5 282 + 30

31 + 3 350 + 30 43 + 4 485 + 45

#10--24UNC

1

8

+

2

3

0

+

5

3

9

+

5

6

42 + 4 475 + 45 60 + 6 675 + 70

#10--32UNF

18 + 2 30 + 5 339 + 56

48 + 4 540 + 45 68 + 6 765 + 70

1/4 -- 20 UNC 48 + 7 53 + 7 599 + 79 100 + 10 1125 + 100 140 + 15 1580 + 170

1/4 -- 28 UNF 53 + 7 65 + 10 734 + 113 115 + 10 1300 + 100 160 + 15 1800 + 170

5/16 -- 18 UNC 115 + 15 105 + 17 1186 + 169 200 + 25 2250 + 280 300 + 30 3390 + 340

5/16 -- 24 UNF 138 + 17 128 + 17 1446 + 192 225 + 25 2540 + 280 325 + 30 3670 + 340

ft--lb ft--lb N--m ft--lb N--m ft--lb N--m

3/8 -- 16 UNC 16 + 2 16 + 2 22 + 3 30 + 3 41 + 4 43 + 4 58 + 5

3/8 -- 24 UNF 17 + 2 18 + 2 24 + 3 35 + 3 47 + 4 50 + 4 68 + 5

7/16 -- 14 UNC 27 + 3 27 + 3 37 + 4 50 + 5 68 + 7 70 + 7 95 + 9

7/16 -- 20 UNF 29 + 3 29 + 3 39 + 4 55 + 5 75 + 7 77 + 7 104 + 9

1/2 -- 13 UNC 30 + 3 48 + 7 65 + 9 75 + 8 102 + 11 105 + 10 142 + 14

1/2 -- 20 UNF 32 + 3 53 + 7 72 + 9 85 + 8 115 + 11 120 + 10 163 + 14

5/8 -- 11 UNC 65 + 10 88 + 12 119 + 16 150 + 15 203 + 20 210 + 20 285 + 27

5/8 -- 18 UNF 75 + 10 95 + 15 129 + 20 170 + 15 230 + 20 240 + 20 325 + 27

3/4 -- 10 UNC 93 + 12 140 + 20 190 + 27 265 + 25 359 + 34 375 + 35 508 + 47

3/4 -- 16 UNF 115 + 15 165 + 25 224 + 34 300 + 25 407 + 34 420 + 35 569 + 47

7/8 -- 9 UNC 140 + 20 225 + 25 305 + 34 430 + 45 583 + 61 600 + 60 813 + 81

7/8 -- 14 UNF 155 + 25 260 + 30 353 + 41 475 + 45 644 + 61 660 + 60 895 + 81

NOTE: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite or thread sealant such as Loctite.

NOTE: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

NOTE: The nominal torque values listed above for

Grade 5 and 8 fasteners are based on 75% of the mini-

mum proof load specified in SAE J429. The tolerance is

approximately +

10% of the nominal torque value. Thin

height nuts include jam nuts.

Workman MD/MDX Page 2 -- 5 Product Records and Maintenance

Standard Torque for Dry, Zinc Plated and Steel Fasteners (Metric Fasteners)

T

h

r

e

a

d

S

i

z

e

Class 8.8 Bolts, Screws and Studs with

R

e

g

u

l

a

r

H

e

i

g

h

t

N

u

t

s

Class 10.9 Bolts, Screws and Studs with

R

e

g

u

l

a

r

H

e

i

g

h

t

N

u

t

s

Thread Size Regular Height Nuts

(Class 8 or Stronger Nuts)

Regular Height Nuts

(Class 10 or Stronger Nuts)

M5 X 0.8 57 + 5in--lb 640 + 60 N--cm 78 + 7in--lb 885 + 80 N--cm

M6 X 1.0 96 + 9in--lb 1018 + 100 N--cm 133 + 13 in--lb 1500 + 150 N--cm

M8 X 1.25 19 + 2ft--lb 26 + 3N--m 27 + 2ft--lb 36 + 3N--m

M10 X 1.5 38 + 4ft--lb 52 + 5N--m 53 + 5ft--lb 72 + 7N--m

M12 X 1.75 66 + 7ft--lb 90 + 10 N--m 92 + 9ft--lb 125 + 12 N--m

M16 X 2.0 166 + 15 ft--lb 225 + 20 N--m 229 + 22 ft--lb 310 + 30 N--m

M20 X 2.5 325 + 33 ft--lb 440 + 45 N--m 450 + 37 ft--lb 610 + 50 N--m

NOTE: Reduce torque values listed in the table above

by 25% for lubricated fasteners. Lubricated fasteners

are defined as threads coated with a lubricant such as

oil, graphite or thread sealant such as Loctite.

NOTE: Torque values may have to be reduced when

installing fasteners into threaded aluminum or brass.

The specific torque value should be determined based

on the fastener size, the aluminum or base material

strength, length of thread engagement, etc.

NOTE: The nominal torque values listed above are

based on 75% of the minimum proof load specified in

SAE J1199. The tolerance is approximately +

10% of the

nominal torque value.

Product Records

and Maintenance

Workman MD/MDXPage 2 -- 6Product Records and Maintenance

Other Torque Specifications

SAE Grade 8 Steel Set Screws

T

h

r

e

a

d

S

i

z

e

Recommended Torque

Thread Size

Square Head Hex Socket

1/4 -- 20 UNC 140 + 20 in--lb 73 + 12 in--lb

5/16 -- 18 UNC 215 + 35 in--lb 145 + 20 in--lb

3/8 -- 16 UNC 35 + 10 ft--lb 18 + 3ft--lb

1/2 -- 13 UNC 75 + 15 ft--lb 50 + 10 ft--lb

Thread Cutting Screws

(Zinc Plated Steel)

Type 1, Type 23 or Type F

Thread Size Baseline Torque*

No. 6 -- 32 UNC 20 + 5in--lb

No. 8 -- 32 UNC 30 + 5in--lb

No. 10 -- 24 UNC 38 + 7in--lb

1/4 -- 20 UNC 85 + 15 in--lb

5/16 -- 18 UNC 110 + 20 in--lb

3/8 -- 16 UNC 200 + 100 in--lb

Wheel Bolts and Lug Nuts

Thread Size

Recommended Torque**

7/16 -- 20 UNF

Grade 5

65 + 10 ft--lb 88 + 14 N--m

1/2 -- 20 UNF

Grade 5

80 + 10 ft--lb 108 + 14 N--m

M12 X 1.25

Class 8.8

80 + 10 ft--lb 108 + 14 N--m

M12 X 1.5

Class 8.8

80 + 10 ft--lb 108 + 14 N--m

** For steel wheels and non--lubricated fasteners.

Thread Cutting Screws

(Zinc Plated Steel)

Thread

S

i

z

e

Threads per Inch

B

a

s

e

l

i

n

e

T

o

r

q

u

e

*

Size

Type A Type B

Baseline Torque

*

No. 6 18 20 20 + 5in--lb

No. 8 15 18 30 + 5in--lb

No. 10 12 16 38 + 7in--lb

No. 12 11 14 85 + 15 in--lb

* Hole size, material strength, material thickness and fin-

ish must be considered when determining specific

torque values. All torque values are based on non--lubri-

cated fasteners.

Conversion Factors

in--lb X 11.2985 = N--cm N--cm X 0.08851 = in--lb

ft--lb X 1.3558 = N--m N--m X 0.7376 = ft--lb

Page is loading ...

Toro Workman MDX Utility Vehicle User manual

Toro Workman MDX Utility Vehicle User manual

Related papers

Other documents