The bluetooth name and Bluetooth registered trademarks are owned by Bluetooth SIG, Inc., and are used by Baracoda under license. The Baracoda names and Baracoda trademarks are
own by Baracoda. All specifi cation are subject to change without notice - Non contractual pictures © Baracoda - All rights reserved
Baracoda, Inc. (US Offi ce) Baracoda SA (Europe Offi ce: France)
45 Main street - Suite 616 - Brooklyn, NY 11201 30 Avenue de l’Amiral Lemonnier - 78160 Marly-Le-Roi
Ph: 718 488 9600 - Fx: 718 488 9601 Ph: +33 1 30 08 89 00 - Fx: +33 1 30 08 89 98
BL1000
© Baracoda™ - September 2004
Important notice
Every effort is made to ensure the accuracy of
our product information; however, we accept no
responsability for errors or omissions including, but not
limited to, the implied warranties of merchantability and
fi tness for a particular purpose. We shall not be liable for
errors contained herein or for incidental consequential
damages in connection with the furnishing, performance,
or use of this material.
Specifi cations or version may be subject to change
without notice. The actual specifi cation and version are
based on the product delivered.
Introduction
Scanning a series of programming bar code labels can
confi gure the scanner.
The scanner must be properly powered before program-
ming.
During the programming mode, the scanner will ack-
nowledge a good and valid reading with a short beep. It
will give long beeps for either an invalid or bad reading.
Programming Guide
T
T
A
A
B
B
L
L
E
E
O
O
F
F
C
C
O
O
N
N
T
T
E
E
N
N
T
T
S
S
1 Configuring your scanner 3
2 Device Option Control Bar Codes 4
2.1
Return to Factory Default Settings...................................................................................................................... 4
2.2
ACK/NAK Protocol...............................................................................................................................................4
2.3
Auto Download Data Enable* Disable............................................................................................................... 4
2.4
Beep Control Enable* Disable ........................................................................................................................... 4
2.5
Delay Between Bar Codes None* 500ms........................................................................................................ 4
2.6
ETX Suffix Character Enable Disable* .............................................................................................................. 5
2.7
LED Control Enable* Disable.............................................................................................................................5
2.8
Line Feed Suffix Character Enable* Disable....................................................................................................5
2.9
STX Prefix Character Enable* Disable .............................................................................................................. 5
3 Symbology Selection Control Bar Codes 7
3.1
Enable all symbologies.........................................................................................................................................7
3.2
Code 39 Enable* Disable................................................................................................................................... 7
3.3
Code 128 Enable* Disable................................................................................................................................. 7
3.4
EAN-8 Enable* Disable....................................................................................................................................... 7
3.5
UPC-A/EAN-13 Enable* Disable ....................................................................................................................... 7
3.6
UPC-E Enable* Disable ...................................................................................................................................... 7
3.7
Supplemental Bar Codes..................................................................................................................................... 8
3.8
AIM Symbol Identifiers Enable Disable*........................................................................................................... 8
3.9
Combine Bar Codes (FWV 1.7.0) Enable Disable* ........................................................................................8
4 Symbology Options Control Bar Codes 10
4.1
Code 9 Options..................................................................................................................................................10
4.2
Code39 Stripped Checksum Enable ................................................................................................................10
4.3
UPC/EAN Options Convert UPC-A codes to EAN-13 codes (FWV 1.8.0) ....................................................... 10
5 Command Control Bar Codes 10
5.1
Clear Device Bar Code Memory........................................................................................................................10
Important notice:
Every effort is made to ensure the accuracy of our product information; however, we accept no responsibility for errors or omissions including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for
incidental consequential damages in connection with the furnishing, performance, or use of this material.
Specifications or version may be subject to change without notice. The actual specification and version are based on the product delivered.
INTRODUCTION
Scanning a series of programming bar code labels can configure the scanner.
The scanner must be properly powered before programming.
During the programming mode, the scanner will acknowledge a good and valid reading with a short beep. It will give long beeps for either an invalid or
bad reading.
BL1000 Programming guide v1.2
© Baracoda - 3 -
1 Configuring your scanner
Setting Baracoda Default Value
Acknowledgment protocol Off
AIM code Off
Automatic data download Enabled
Baud rate 4800
Beep On
Code 128 symbology Enabled
Code 39 checksum Off
Code 39 strip check character Off
Code 39 symbology Enabled
Combined bar codes Off
Convert UPC-A bar codes to EAN-13 format
(FWV 1.8.0)
Off
Delay between bar code transmissions (FWV
1.6.0)
No delay
Standard vs. aggressive scanning (FWV 1.8.0) Standard
Download format Compatible
EAN-8 symbology Enabled
ETX enable Off
Expand UPC-E codes Do not expand
LED On
Linefeed On
NCR symbol identifiers Off
STX On
Supplemental bar codes Auto-detect
Timestamp Off
UPC-A/EAN-13 symbology Enabled
UPC-E symbology Enabled
BL1000 Programming guide v1.2
To use these bar codes to configure the BL1000, print the appropriate page. Then use your scanner to read the
appropriate bar code.
2 Device Option Control Bar Codes
2.1 Return to Factory Default Settings
2.2 ACK/NAK Protocol
Enable Disable*
2.3 Auto Download Data
Enable* Disable
2.4 Beep Control
Enable* Disable
2.5 Delay Between Bar Codes
None* 500ms
1100ms 1 600ms
© Baracoda - 4 -
BL1000 Programming guide v1.2
*Factory Default Setting
2.6 ETX Suffix Character
Enable Disable*
2.7 LED Control
Enable* Disable
2.8 Line Feed Suffix Character
Enable* Disable
2.9 STX Prefix Character
Enable* Disable
© Baracoda - 5 -
BL1000 Programming guide v1.2
© Baracoda - 6 -
* Factory Default Setting
BL1000 Programming guide v1.2
3 Symbology Selection Control Bar Codes
3.1 Enable all symbologies
3.2 Code 39
Enable* Disable
3.3 Code 128
Enable* Disable
3.4 EAN-8
Enable* Disable
3.5 UPC-A/EAN-13
Enable* Disable
3.6 UPC-E
Enable* Disable
* Factory Default Setting
© Baracoda - 7 -
BL1000 Programming guide v1.2
3.7 Supplemental Bar Codes
Auto-Detect Supplemental Codes*
Require Supplemental codes Disable Supplemental Codes
3.8 AIM Symbol Identifiers
Enable Disable*
3.9 Combine Bar Codes (FWV 1.7.0)
Enable Disable*
© Baracoda - 8 -
BL1000 Programming guide v1.2
© Baracoda - 9 -
* Factory Default Setting
BL1000 Programming guide v1.2
4 Symbology Options Control Bar Codes
4.1 Code 9 Options
Code39 Checksum Enable Code39 Checksum Disable*
(Disables both Code 39 Checksum options)
4.2 Code39 Stripped Checksum Enable
4.3 UPC/EAN Options
Convert UPC-A codes to EAN-13 codes (FWV 1.8.0)
Do Not Convert UPC-A codes*
#
(FWV 1.8.0)
Expand UPC-E codes to UPC-A codes Do Not Expand UPC-E codes*
5 Command Control Bar Codes
5.1 Clear Device Bar Code Memory
© Baracoda - 10 -
BL1000 Programming guide v1.2
© Baracoda - 11 -
* Factory Default Setting
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Baracoda BRR-LA Evolution Programming Manual
-
-
-
-
-
Nextel comm BRR-L User manual
-
-
-
-
