jWIN JD-VD502 User manual

FEATURES...................................................A1-A2

IMPORTANT POINTS ..................................B1-B3

OPER

ATION INTERFACE.............................C1-C2

BASIC PLAYBACK.......................................D1-D6

SYSTEM SETUP...........................................E1-E4

TROUBLESHOOTING........................................F1

SPECIFIC

ATIONS.............................................G1

ADDITIO

NAL INFORMATION............................H1

CONTENTS

A1

FEATURES

Please read this Safety & Operation Manual before you install and use

this unit, and please follow the instructions. Please pay attention to any

Warnings or Notices in the text.

Route the power cord so that it is not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to the plugs, receptacles, and the point

where the cord exists from the appliance.

Please disconnect the unit if any of these conditions occur:

Do not overload wall outlets, extension cords or convenience receptacles beyond their

capacity, since this can result in fire or electric shock.

Do not use an unsuitable outlet, it might be dangerous.

Check the connection regularly. If any rupture or failure in insulation occurs, call for

maintenance and have them replaced.

To ensure reliable operation and to protect it from overheating, the unit must be used

in a well-ventilated area.

Do not use power-line operated sets near water – for example, near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.

Do not place the unit on an unstable object. The set may fall, causing serious injury to

a child or an adult, and serious damage to the unit.

Never let any liquid spatter on the unit. It might cause electric shock or fire hazard.

Never place the unit near or over such objects: for example, radiators, heat registers,

stoves, or other heat sources (including audio amplifiers).

Unplug the unit from the wall outlet before cleaning or polishing it. Do not use liquid

cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the

exterior of the unit.

Never place heavy object on the unit.

A2

FEATURES

Copyrights:

The copyright protected content cannot be copied, broadcast, screened, cablecast,

or played publicly and rented, unless it is authorized.

Do not use cracked or anamorphic discs in the unit, or it might damage the loader.

Do not repair the unit yourself. Opening or removing the cover may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug the unit and refer servicing to qualified service personnel under the

following conditions:

A. When the power cord or plug is damaged or frayed

B. If liquid has been spilled or objects have fallen into the unit

C. The unit has been exposed to rain or water

D. If the unit does not operate normally when following the operating instructions

E. If the unit has fallen or the cabinet has been damaged

F. When the unit exhibits a distinct change in performance – this indicates a need

for service

Tips: Upon completion of any service or repairs, ask the service technician

to perform routine safety checks to determine that the unit is safe to operate.

Remote Control Notice

--Aim the remote directly at the receiver on the unit while operating it.

--Do not let the remote fall, especially from a high place

--Do not place the remote in a hot or moist location

--Do not let any water or other liquid fall on the remote

--Do not open the remote control, except to changeits batteries

--Do not use the remote control at a distance greater than 7 meters (about 23 feet) from

the unit, nor at an angle which exceeds 30° away from the center of the TV

--Do not expose the infrared receiver on the JD-VD502 (see page B1, item 13) to a

strong light source, such as sunshine or bright lights, or the remote control may not

operate consistently

The specifications and manual are subject to change without notice.

Operation Interface

FRONT PANEL:

REAR PANEL:

4. Component Video (Y) Output

5. Component Video (Pb/Cb) output

6. Component Video (Pr/Cr) output1. Left Front Channel Output

8. Left Surround Channel

10. Center Channel Output

14. S-Video Output

7. Composite Video Output

12. Right Audio Output

11. Left Audio Output

13. Digital Coaxial Output

15. Digital Optical Audio Output

2. Right Front Channel Output

9. Right Surround Channel Output

3. Subwoofer Output

1

8 9 10 11 12 13 1514

2 3 4 5 6 7

11 12 131098

1. POWER

2. PLAY

3. PAUSE

4. STOP

5. FWD

6. REV

7. OPEN/CLOSE

8. MIC1

9. MIC2

10. MIC VOL1

11. MIC VOL2

12. VFD DISPLAY UNIT

13. RECEIVER

90

S-Video Connecting Wire

Composite V ideo

Connecting Wire

REMOTE CONTROL:

Operation Interface

Basic playback

C1

Playing a CD (e.g. music) disc

1. Place the CD in the disc compartment.

2. The unit automatically shows the disc's contents.

3. On the remote control, choose the number key(s) that corresponds to the track

to be played.

For example: --If you want to play Track 8, press the "8" number key.

--If you want to play Track 12, first press the "+10" number key,

followed by the "2" key. The combination of "+10" and "2"

corresponds to 12.

Playing a VCD (Video CD) or SVCD (Super-Video CD) disc

1.Place the VCD or SVCD in the disc compartment.

2.After reading the disc, the PBC (Playback Control) menu will display on the

TV screen if the disc has been provided with one. See the NOTICE, below.

3.Choose the chapter you want to play by pressing the corresponding number on

the remote control. Use the "+10" key, if necessary, as described above.

NOTICE: If your VCD or SVCD disc has been recorded with a PBC (Playback

Control) track, your JD-VD502 will display that information as a menu system

on the TV screen, which provides convenience when choosing which part of the

disc's contents will be played.

Bear in mind that the PBC information must be on

the disc for the menu to be displayed.

Play DVD disc

1.Place a DVD in the disc compartment.

2.The unit reads the DVD and automatically plays the disc, displaying any menu

provided.

3.Using the keys on the remnote control, choose the desired contents you want.

folder 01

00:00 00:00

001/008

folder 01

001......

00:00 00:00

001/016

folder 01

002......

003......

004......

MP3

.........

Basic playback

Playing an MP3 disc:

1.Place the MP3 in the disc compartment.

2.After the unit reads the contents of the MP3 disc, the TV screen will

display the menu in the manner shown below:

(1)

1.Choose the desired folder of file you want by moving the cursor, and

press “Enter” to confirm your selection.

2.If you chose a folder, then the files within the folder are displayed.

3.If so, choose the desired MP3 track you want by moving cursor, pressing

Enter to confirm, or you can choose it directly through the number keys.

(2)

Playing a Kodak Picture CD disc:

1.Place the Kodak Picture CD in the disc compartment.

2.After reading the contents, it will play automatically.

Playing a disc with JPEG files:

1.Place a disc with JPEG files in the disc compartment.

2.After unit reads its contents, it will show the list of .JPG files on the TV

screen.

3.Choose the JPEG file you wish to view by moving the cursor to highlight it,

and then by pressing "Enter" to view it. Alternatively, you may choose the

number keys.

C2

Basic Playback

D1

1 [POWER]

Press this key to turn the JD-VD502's power on and off.

2 [OPEN/CLOSE]

Press OPEN/CLOSE to open the tray, and then place the disc on it. Press this button again to close

the tray. When the disc has loaded, the TV screen will display the disc type, and its content will be

automatically played or displayed. Note that discs containing MP3 and JPEG files cannot be played

automatically.

3 [PLAY/ENTER]

Press to play or confirm your selections.

4 [PAUSE/STEP]

In play mode, press this key to pause; each subsequent press will move the picture one frame at a time.

Press "PLAY" again to resume normal playback.

5 [MENU]

In the DVD play mode, press MENU key once to return to the most recent submenu. Press it again to

return to the main menu. For VCD and SVCD playback, refer to the details on page C1.

Once done, press the number key selecting your desired song. If you want to cancel disc playback,

press the MENU key. The TV screen will show "PBC off". Then, press number keys to select desired song.

6 [STOP]

Press STOP one time, and the unit will memorize the stopped position. When the unit continues playing,

it will play from the previously stopped position. Pressing STOP the second time causes the unit to stop

playing and cancels the memorized position.

Basic Playback

D2

2x* 4x* 8x* 16x* 32x*

1 [PREV/NEXT]

When playing DVCDs (Dual VCDs--an extended length VCD format), SVCDs, VCDs, CDs, and MP3s,

press <Skip Backward> to go to the previous chapter. When playing DVDs, press <Skip Backward> to

go to the previous chapter or title. Press <Skip Forward> to advance to the next chapter.

2 [REW/FF]

When playing DVDs, SVCDs, VCDs, CDs, and MP3s, press this key to play forward or backward,

according to the figure below:

3 [AUDIO]

If the S-VCD, VCD, or CD disc has multi-channel capability, you can press this button to select the

sound from left channel out, right channel out, stereo out, or downmix out .

Press this button to select your desired language when playing DVD, S-VCDs which have

multi-language capability.

4 [TITLE]

Press this button to return to the title of the first chapter or playback selection.

5 [CLEAR]

Clear memory playback: Select the memory position you want to play by using the direction keys on

the remote control.

Note: If the power is off or the disc is removed, all the memorized positions will be lost.

6 [ZOOM]

By pressing this button, you can appreciate the zoom picture. Only in the zoom state can you move the

picture by the remote control's direction keys.

7 [VOL]

Volume: Press these keys to adjust the output volume.

Press the "+" key to increase the volume in up to 20 upward steps. Press the "--" key to decrease the volume in

up to 20 downward steps.

BasicPlayback

1[PROGRAM]

If the disk has more than twochapters ortitles,youcanpressthisbuttontoset upthe playback order

that you prefer.

Press the PROGRAMkeytoindicate, on the TV, the order that you want to play the contents of your disc.

PRGOTT--/CH--[TT--(TITLE)CH--(CHAPTER)]

01TT:__CH:__06TT:__CH:__

02TT:__CH:__07TT:__CH:__

03TT:__CH:__08TT:__CH:__

04TT:__CH:__09TT:__CH:__

05TT:__CH:__10TT:__CH:__

EXITSTARTBACK

PROG:MENU00-00

01__0600(MENU)

02__07__

03__08__

04__09__

05__10__

EXITSTARTBACK

D4

1 [DISPLAY]

Press DISPL

AY to display the information referring to the disc on the TV screen.

DVD playback

VCD (and VCD Ver. 2.0) playback after closing the PBC (Playback Control).

play super VCD,VCD2.0 after opening the PBC (Playback Control)

Basic Playback

D5

D6

03*18 05*28

058/158

- - - - - - -

Three modes of operation are available using the Remote Control's PROGRAM key. Press once to change:

1. Folder Play Mode

In the folder mode, press the remote control's direction keys to select the desired MP3 folder, and press the

Enter key to view the folder's contents. Then, press the remote's direction keys to select the desired MP3

file, or use the remote control's number keys (as in ###, e.g. 009) and press Enter to make the selection.

2. Normal Listing Play mode

In the Normal Listing Play mode, the unit will read all tracks of the disc, and play the contents of each folder

in turn. Press the number key to select the tracks to be played directly.

Play MP3 disc:

After the unit reads the contents of the MP3 disc, the TV screen will show the following:

Play time Track time Volume Working Dynamic

modulation state frequency

Playing track

Tracks of disc

Basic Playback

D7

00*00 00*00

058/158

- - - - - - -

JPEG

Distinguishing rate 888 X 1200

Playing track

Tracks of disc

Working state

Picture preview

Basic Playback

Instruction of Function key:

Prog key -> Selects the switch mode of picture

Stop key -> Enters picture preview mode

key -> Skips ahead to the next picture.

key -> Skips back to the last picture.

Play/Enter key -> Enters picture playing mode

*

Viewing a Kodak Picture CD:

After the unit reading the content of a Kodak picture CD, the TV screen displays:

E1

When the unit is working, press the setup key to enter setup menu.

Press the direction key " " to move cursor to the desired setup page, and press the Enter key

to confirm.

Press the direction key " " " " to move cursor to the desired setup item, and press the Enter

key to confirm.

Press the direction key " " to return to last Setup item.

Note:

1. Moving to theselected item will produce a relevant list of features at the bottom of the screen.

2. If a selection is "grayed out" it cannot be chosen in the current context.

3. The setup selections remain in effect even when the unit's power is off.

General Audio

Dolby

Video

General Setup introduction:

TV Display

A.Normal/PS: When the unit connects with TV set,

wide image is showed on the whole screen, but a

part is cut.

B.Normal/LB: When the unit connects with TV set,

playing wide image, there are black bands showed

on the up and down screen.

C.Wide: Choose this when the unit connects with

wide screen TV se

D.wide squeeze

t.

Angle Mark: Select display angle, when playing

multi-angle DVD disc.

OSD Language: Select operation language.

Captions:This function is ineffective if no caption

record in the disc. If the caption is closed, press

the caption key on the remote control to open

captions function to select captions language.

S

Hdcd

This setup can adjust to different sampling rates

used by HDCD discs by using multiples of the standard

44.1 KHz sampling rate found on common CDs.

Choose the correct sampling rate for the HDCD disc

being played.

creensaver

When the Screensaver is on, to prevent aging or damage

to the TV's CRT picture tube, if applicable, a floating

picture will be produced for several minutes after the unit

stops playing, preventing a possible "burned-in" image.

General Setup Page

TV Display PS Normal/PS

Normal/LB

Wide

Angle Mark ON ON

OFF

OSD Language English

Captions OFF ON

OFF

Screen saver ON ON

OFF

Hdcd 1x 2x

1x

OFF

SYSTEM SETUP

E

Spanish

nglish

Preference

wide squeeze

Audio Setup Page:

Speaker Setup

Spdif Setup

Speaker Setup Page

Down mix LT/RT

Stereo

5.1

Front Speaker Lrg Large

Small

Center Speaker Sml Large

Small

OFF

Rear Speaker Sml Large

Small

OFF

Subwoofer ON ON

OFF

There are several setup pages discussed in the following

material. In the Audio category, there are two main areas:

Downmix:

Dialog volume:

In LT/RT or stereo output mode, set up this item

to adjust voice, within the range from 0 to 20.

SYSTEM SETUP

SPDIF output:

When you have an external audio system (e.g. a Home Theater

System) that can accept digital audio signals via a coaxial or

optical cable, SPDIF should be turned on (see below). Doing

so enables the digital signals that leave the JD-VD502 to be

processed by Dolby and DTS Home Theater systems, among

many other devices that have internal decoders capable of

RAW decoding.

Select SPDIF/RAW when you have a receiver that can decode

the digital signal internally. SPDIF is the preferred option in

most cases. If you don't hear any output, then switch to

SPDIF/PCM.

Select SPDIF/PCM when the unit is connected to a 2-channel

digital stereo amplifier, or equivalent device, which does NOT

have the ability to decode the signal.

Select SPDIF/OFF if you do not have a receiver capable of

processing digital audio.

SPDIF Setup Page:

SPDIF output RAW SPDIF OFF

SPDIF RAW

SPDIF/PCM

SYSTEM SETUP

Dolby Digital Steup

Dual Mono

Dynamic

Mic Off Off

ON

Stereo

L-Mono

R-Mono

Mix-Mono

Dual Mono

This option allows you to set the output methods for

the left and right audio signals. There are 4 modes:

stereo,left sound channel, right sound channel, and

mixed sound channel, to be selected according to the

AC-3 KARAOKE mode.

Dynamic

You can change the zip mode to “Dual Mono” in

order to adjust linear zip ratio and obtain the zip

effects for different signals. If you choose FULL, the

peak value of audio signal is minimum, and becomes

maximum if you choose off.

Br

Component:

S-Video: Choose this setting if your DVD player

is connected to a TV with an S-Video cable or

composite video cables (Yellow/Red/White).

Tv-Mode:

Interlace-YUV: Choose this setting if your DVD

player is connected to a TV with Y, Cb, Cr video

cables.

P-SCAN: Choose this setting if your DVD player

is connected to a progressive scan TV with Y,

Cb, Cr video cables.

ightness:

Setup this item to control the brightness of

image, available range from 0 to +20.

Hue:

Setup this item to control the hue of image,

available range from 0 to +9.

Contrast:

Setup this item to control the contrast of

image, available range from 6 to +16.

V

Component

TV Mode

ideo Setup Page

Brightness 00 Brightness |||||||||......0

Contrast 00 Contrast |||||||||......0

Sharpness Low

S-video S-video

Yuv

P-Scan

Interlace

High

Medium

Low

SYSTEM SETUP

4

Preference Page:

TV Type PAUTO al

Multi

Ntsc

Audio Eng

Eng

Subtitle

Disc Menu

Default Reset

TV TYPE:

The JD-VD502 can operate with every type of TV

throughout the world. Select your TV type below:

Multi : Automatically selects the "TV Type" according

to the color system of any disc that is currently playing.

NTSC: Taiwan, Japan and USA use this type.

PAL: Hong Kong, China and Europe use this type,

When the "TV Type" is inconsistent with this setup,

the screen will be incoherent and difficult to view.

Audio: Subtitle and disc menu language setup:

If a disc is equipped with corresponding subtitles,

audio menu languagesupport is valid. However, if

the disc has only a fixed language, this setup will

be invalid.

Default:

Selecting this option returns the player's settings

to their original factory (default) settings.

English

Japanese

Fr nce h

Italian

Spanish

Russian

Ch

i

nese

Thal

Page is loading ...

jWIN JD-VD502 User manual

jWIN JD-VD502 User manual

Other documents