Microh NEO WASH ZM60TS User manual

Brand: Microh

Model: NEO WASH ZM60TS

Category: Stroboscopes & disco lights

Type: User manual

Microh NEO WASH ZM60TS is a professional-grade wash light designed for a wide range of applications. With its powerful 4 x 15W 4-in-1 QUAD (RGBW) LEDs, the NEO WASH ZM60TS delivers a bright and even wash of color over a wide area. The fixture's 10° - 60° zoom range makes it suitable for both short-throw and long-throw applications, while its pan and tilt capabilities allow for precise positioning of the light beam.

The NEO WASH ZM60TS offers multiple control options, including DMX-512, master/slave, and sound activation. The fixture's built-in microphone allows for sound-to-light effects, while its 10-channel DMX mode provides detailed control over all of the fixture's parameters.

USER MANUAL

Please read this user manual before using this product

Introduction

Thank you for purchasing the MICROH DJ NEO WASH ZM60TS. For your own

safety and knowledge, please read this manual before installing or operating

this device. This manual covers the important information on installation and

applications. Please install and operate the xture according to instructions.

Meanwhile, please keep this manual for future reference.

Please carefully unpack the xture and check all areas to see if it was damaged

during transportation. Please check whether the following items are included in

the package:

Item Quantity

NEO WASH ZM60TS xture 1

Power cord 1

DMX Cable 1

Bracket 1

User manual 1

Notify the shipper immediately and retain packing material for inspection if any parts

appear damaged from shipping or the carton itself shows signs of mishandling.

Save the carton and all packing materials. In the event that a xture must be

returned to the factory, it is important that the xture be returned in the original

factory box and packing.

Safety Warning

• Every person involved with the installation, operation and maintenance of this

device must be qualied.

• User/installer must follow the instructions of this manual.

• Unqualied persons must not open the housing cover and operate the device,

or the dealer will not accept liability for any resulting defects or problems.

• Protect the device against rain and moisture device with other electrical equipment.

• During move and installation, make sure the device is not stored with metal

parts and other tough materials.

• Always disconnect from the main power sources. Do not install or dismantle

when the device is powered on.

• The minimum distance between light output and the Illuminated surface must

be more than 50cm.

• The device must only be installed on a non-ammable surface. In order to

safeguard sufcient ventilation, please leave 50cm of free space around the

device. Note that heat-sensitive objects may be deformed or damaged by the

emitted heat of this xture.

• During operation, the housing may become very hot! Do not operate the device

for 15 minutes after switching off.

• The maximum ambient temperature Ta = 45°( must never be exceeded). The

maximum housing temperature Tb = 80°( must never be exceeded).

• This xture is for indoor use.

• Replace any visible cracked protective shields, lters, and lenses.

• The protective shields, lters, and lenses will require weekly cleaning as

smoke “cuid” tends to build up residues, reducing the light output very quickly.

CAUTION!

Never touch the device during operation!

The housing may heat up!

CAUTION!

Never look directly into light source,

as sensitive persons may suffer from an epileptic shock.

Caution!

• Unqualied person involved with installation, operation and maintenance of

this device is prohibited.

• If any of the above mentioned problems happen, or unknown problems happen,

please contact manufacturer or distributor for assistance.

Operation

Press the function key Menu cycled out of eight different functional effects, digital

tube in which the rst two digits represent the current function (see menu). The

last two digits represent the kinds of functions which the address code, or speed

parameters. Press Down or UP key to modify its parameter values. Press the Enter

key to conrm.

Level 01 Menu Level 02 Menu

Addr (DMX Address) 001-512

Chnd (Channel Mode)

10CH

12CH

15CH

Slnd (Master/Slave Mode)

Master

Slave 01

Slave 02

Shnd (Show Mode) Show 01 - Show 04

Auto (Auto-run Mode)

Non-automatic

Automatic

Soud (Sound Control) On - Off

Soen (sound Sensitivity) 000-100

Blac (Pause Mode)

Stop

Start Up

LED (Backlit) On - Off

Disp (Display Flip) disp-dsip

Pan (X-axis Flip) Yes - No

Tilt (Y-axis Flip) Yes - No

Level 01 Menu Level 02 Menu

Menu (Menu Test)

Pan

Tilt

Zoom

Red

Green

Blue

White

Dimmer

Strobe

Test (Automatic Test) Test

Rest Reset

Features

• Built-in Microphone

• Pan/Tilt Inversion

• 10° - 60° Wash Zoom

Specications

Lamp/LED Zoom 4 x 15W 4 in QUAD (RGBW) LED WASH

LED Life: 50,000 hrs

Voltage: 95V-240VAC, 50/60Hz

Power Consumption: 70W

Power Connection: IEC In

Data Connection: 3 Pin XLR

Wash Angle: 10° - 60°

Strobe Pulse: 0-12Hz

Pan: 540°

Tilt: 270°

Modes: Auto, DMX, Master/Slave, Sound

DMX Channels: 10CH/ 12CH/ 15CH

Dimensions (mm): 470 x 310 x 305

Weight: 2.7 Kg

Operation (cont.)

Mounting And Installing

Caution: for added protection, mount the xture in areas outside walking paths,

seating areas, or in areas were the xture might be reached by unauthorized

personnel. Before mounting the xture to any surface, make sure that the

installation area can hold a minimum point load of 10 times the devices weight.

Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable. Never stand directly below the device when

mounting, removing, or servicing the xture.

Whether installing inverted on a truss or ceiling, or set on a at level surface be

sure this xture is kept at least 0.5m (1.5ft) away from any ammable materials

(decorations, etc.). Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the clamp fails.

Mounting Points: Overhead mounting requires extensive experience, including

calculating working load limits. A knowledge of the installation material being

used, and periodic safety inspection of all installation material and the xture are

all imperative and should only be performed by a qualied technician. Improper

installation can result in bodily injury or damage.

Clamp Mounting: The MICROH DJ NEO WASH ZM60TS provides a unique

mounting bracket assembly that integrates 2 brackets to be used to mount on

a truss or the oor. When mounting this xture to truss, be sure to secure an

appropriately rated clamp to the included bracket tted through the center hole.

As an added safety measure, be sure to attach at least one properly rated safety

cable to the xture.

Regardless of the rigging option you choose for your MICROH DJ NEO WASH

ZM60TS xture, always be sure to secure your xture with a safety cable. The

xture provides a built-in rigging point for a safety cable hanging bracket. Be sure

to only use the designated rigging point for the safety cable and never secure a

safety cable to a carrying handle.

DMX -512 Control Connections

This xture complies with international USITT DMX standards and can be used

with a 3 pin DMX connector. Plug in the 3 pin XLR cable to the female 3 pin XLR

output of your controller and the other side to the male 3 pin XLR input of the

xture. To connect the units to DMX, you must daisy chain the xtures together

as a referred in the diagram below. Always end your DMX-512 connection with at

DMX terminator.

For installations where the DMX cable has to run for a long distance, or as an

electrically noisy environment, it is recommended to use a DMX terminator. This

helps in preventing corruption of the digital control signal by electrical noise. The

DMX terminator is simply an XLR plug with a 120 resistor connected between pins

two and three, which is then plugged into the output XLR socket of the last xture

in the chain.

DMX Modes

CH Mode

10CH 12CH 15CH Value Function

1 1 1 000-255 Pan (0-100%)

2 2 2 000-255 Tilt (0-100%)

3 3 3 000-255 Zoom (0-100%)

4 000-255 Pan/Tilt (fast to slow)

4 4 5 000-255 Red Dimmer (0-100%)

5 5 6 000-255 Green Dimmer (0-100%)

6 6 7 000-255 Blue Dimmer (0-100%)

7 7 8 000-255 White Dimmer (0-100%)

8 8 9 000-255 Master Dimmer (0-100%)

9 9 10

000-007 Close

008-015 Open

016-131 Strobe (slow to fast)

132-139 Open

140-181 Fast close to slow open

182-189 Open

190-231 Fast open to slow close

232-239 Open

240-247 Random Strobe

248-255 Open

10 11

000-007 No Function

008-011 Colour 01

012-015 Colour 02

016-019 Colour 03

020-022 Colour 04

023-026 Colour 05

027-030 Colour 06

031-034 Colour 07

035-037 Colour 08

038-041 Colour 09

042-045 Colour 10

046-048 Colour 11

049-052 Colour 12

053-056 Colour 13

057-060 Colour 14

(cont)

061-063 Colour 15

064-067 Colour 16

068-071 Colour 17

072-075 Colour 18

076-078 Colour 19

079-082 Colour 20

083-086 Colour 21

087-089 Colour 22

090-093 Colour 23

094-097 Colour 24

098-101 Colour 25

102-104 Colour 26

105-108 Colour 27

109-112 Colour 28

113-115 Colour 29

116-119 Colour 30

120-123 Colour 31

124-127 Colour 32

128-131 Colour Macro 01

132-135 Colour Macro 02

136-139 Colour Macro 03

140-143 Colour Macro 04

144-147 Colour Macro 05

148-151 Colour Macro 06

152-155 Colour Macro 07

156-159 Colour Macro 08

160-163 Colour Macro 09

164-167 Colour Macro 10

168-171 Colour Macro 11

172-175 Colour Macro 12

176-179 Colour Macro 13

180-183 Colour Macro 14

184-187 Colour Macro 15

188-191 Colour Macro 16

192-195 Colour Fade Macro 01

196-199 Colour Fade Macro 02

200-203 Colour Fade Macro 03

(cont)

204-207 Colour Fade Macro 04

208-211 Colour Fade Macro 05

212-215 Colour Fade Macro 06

216-219 Colour Fade Macro 07

220-223 Colour Fade Macro 08

224-227 Colour Fade Macro 09

228-231 Colour Fade Macro 10

232-235 Colour Fade Macro 11

236-239 Colour Fade Macro 12

240-243 Colour Fade Macro 13

244-247 Colour Fade Macro 14

248-251 Colour Fade Macro 15

252-255 Colour Fade Macro 16

11 12 000-255 Colour Macro Speed (slow to fast)

000-015 No function

016-035 Macro 01

036-055 Macro 02

056-075 Macro 03

076-095 Macro 04

096-115 Macro 05

116-135 Macro 06

136-155 Macro 07

156-175 Macro 08

176-195 Macro 09

196-215 Macro 10

216-235 Macro 11

236-255 Macro 12

14 000-255 Pan/Tilt Speed (slow to fast)

10 12 15

000-069 No function

070-079 When Pan/Tilt axis moving, shut the lights

080-179 No function

180-189 Auto Run

190-199 No function

200-209 Reset

210-255 No function

PLEASE NOTE:

All information for this product is subject to change without notice!

Maintenance and Cleaning

The following points have to be considered during the inspection:

1. All screws for installing the device, or parts of the device must be tightly

connected, and must not be corroded.

2. There must not be any deformations on the housing, colour lenses, xations or

installation spots (ceiling, suspension, trussing).

3. Mechanically moved parts must not show any traces of wearing and must not

rotate with unbalances.

4. The electric power supply cables must not show any damage, material fatigue

or sediments.

Further instructions depending on the installation spot and usage must be handled

by a skilled installer or technician. Any safety issues must be resolved.

CAUTION!

Disconnect xture before servicing.

In order to keep the xture in good condition and extend the life, we suggest regular

cleaning to the xture.

1. Clean the inside and outside lens each week or 100 operation hours to prevent

the light output from darkening due to accumulation of dust, dirt, etc.

2. Clean the fan each week or 100 operation hours.

3. A detailed electrical check by an approved technician every three months is

advised. Ensure the circuit contacts are in good condition, and prevent from

overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint-free

cloth. Never use alcohol solvents.

There are no serviceable parts inside the device. Please refer to the instructions

under “Installation Instructions.”

Should you need any spare parts, please order genuine MICROH DJ parts from

your local dealer.

CAUTION!

Take care using this equipment! High voltage risk of electric shock!

For more information please contact:

www.microhdj.com

[email protected]

905.428.9062

Microh NEO WASH ZM60TS User manual

Brand: Microh

Model: NEO WASH ZM60TS

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

Microh NEO WASH ZM60TS User manual

Microh NEO WASH ZM60TS User manual

Related papers

Other documents