Microh LED Max Zoom AW User manual

Brand: Microh

Model: LED Max Zoom AW

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

LED MAX ZOOM QUAD

www.microhpro.com

USER MANUAL

Please read this user manual before using this product

Introduction

Thank you for purchasing the MICROH LED MAX ZOOM QUAD xture. For

your own safety and knowledge, please read this manual before installing or

operating this device. This manual covers the important information on installation

and applications. Please install and operate the xture according to instructions.

Meanwhile, please keep this manual for future reference.

The LED MAX ZOOM QUAD can make a very bright colourful and dynamic light

scenery effects. The operation fron has three digital displays. You can operate it

through the three buttons (Mode, Up, Down). At the same time , you can adjust

the focus through the distance of the lens. It can stock running mode when it is off.

You can nd the last running mode when it is powered on next. This product has a

temperature protected function. When it is on, it will power off automatically when

the temperature is beyond 85°C, this wont impact other combined xtures. When

you re-start it can run correctly within 85°C.

Please check whether the following items are included in the box:

Item Name Quantity

LED MAX ZOOM QUAD xture 1

Gel Plate 1

User manual 1

Features

• 3 Pin XLR In and Out

• Built in microphone

• LED digital display

• 5 channel DMX

Specications

Voltage: 120V, 60Hz , 125W

Fuse: 3A

Lamp: 24 x 5 Watt 4 in 1 LEDs

Modes: Auto, Master/Slave, Sound, DMX

Beam angel: 10°-60°

Fixtures Size: 30x27x22cm

Gross Weight: 7.3Kg

Safety Instructions

This device has left the factory in perfect condition and to ensure safe operation,

it is absolutely necessary for the user to follow the safety instructions and warning

notes written in this user manual.

IMPORTANT!

Damages caused by the disregard of this user manual are not subject to

warranty. The dealer will not accept liability for any resulting defects or problems.

If this device has been exposed to temperature changes, do not switch it on

immediately. The arising condensation could damage the device. Leave the device

switched off until it has reached room temperature, and is dry.

This device falls under protection-class I, therefore it is essential that the device be

grounded. The electrical connection must be carried out by a qualied technician.

This device should only be used with rate voltage and frequency. Make sure that

the available is not higher than 120V.

Make sure the power cord is never crimped or damaged in any way, as this could

cause shock and damage. If your power cord is damaged in any way, please

purchase a new power cord from your local MICROH dealer. Always disconnect

power, when the device is not in use or before cleaning it. Never pull out the plug

by tugging the power cord.

During initial start-up, some smoke or smell may arise. This is a normal process,

and does not necessarily mean that the device is defective. It should decrease

gradually. Please do not project the beam onto combustible substances.

Fixtures cannot be installed on or near combustible substances. Keep more than

50cm distance from wall or proper ventilation and air ow. If your xture is or has

become damaged in any way, it shall be exclusively replaced or repaired by the

manufacturer to avoid any hazard.

CAUTION!

Never touch the device during operation! The housing may heat up!

CAUTION!

Never look directly into the light source,

as sensitive persons may suffer an epileptic shock.

CAUTION!

The electric connection must only be carried out by a qualied electrician.

Operation

To select one of the run modes, press the MODE button and UP button, when it

is on. You can initialize it at extra factory setting, running on the auto-run program

mode. Under any running mode, press the MODE + UP buttons, the LED display

light will be on, When you press the mode MODE + DOWN buttons, the LED

display will turn off until you press any button. If you don’t press any button, the

LED display light will be turned off automatically after 20 seconds.

Manual Zoom Control

Press the MODE button for 4 seconds (except under slave and DMX mode), the

unit will display “O.T.r.” and after two seconds the display will show 000 or value

zoom set to (0-190), 0 is start (60°), 190 is terminal (10°). To adjust the zoom, use

the UP and DOWN buttons to set your preferred setting. Once you have reached

your desired size, press the mode button to go back to your standalone setting.

The display will go back to the previous mode you were in. The setting will remain

in memory until you change it again.

Static Colour Program Select Running Mode

Press the MODE button, select static colour, select program running mode. At this

time, the display reads “CL.x”,Press UP or DOWN to select static colour 0-7 under

this mode.

Colour Change Program Run Mode

Press the MODE button, select three colours change program running mode. At

this time the three digital tube displays “J.XX”. Press UP of DOWN button to select

the change speed grade 1-99 under this mode (from slow to fast).

Colour Mixing Program Run Mode

Press the MODE button, select three colours dreaming program running mode.

At this time, the three digital tube displays “FXX.” Press UP or DOWN buttons to

select the change speed grade 1-99 under this mode (from slow to fast).

Auto Run Program Mode

Press the MODE button, select Auto-run program mode. At this time, the three

digital tube displays “A--.” Pressing UP and DOWN is not assessable under this

mode. The colours changed program and colour mixing program run alternately.

Running speed is the current speed of colours changed program and colour mixing

program.

Sound Active Program Mode

Press the MODE button, selecting Auto-run program mode. At this time, the three

digital tube displays “S.XX.” Press UP or DOWN to select sound-active sensitivity

grade 0-31. 0 is off sound active, 1 is the lowest sensitivity, 31 is the highest sensitivity.

Slave Running Program Mode

Press the MODE button, selecting Auto-run program mode. At this time, the three

digital tube displays “S.L.A.” Pressing UP and DOWN is not accessible in this mode.

DMX Control Running Program Mode

Press MODE button, select DMX running program mode. At this time, the three digital

tube displays DMX address “XXX.” Press UP or DOWN buttons to select DMX address.

You can set 512pcs addresses. It will  icker when the controller has no signal.

Setup Menu

Mode Setup Up/Down Instruction

DMX

Mode

addresses

Set the DMX starting address

Channels

Unit occupies 5 DMX channels

Unit occupies 6 DMX channels

Unit occupies 7 DMX channels

Unit occupies 8 DMX channels

Zoom

Direction

Zoom direction up, the bigger

DMX value, the bigger beam

angle

Zoom direction down, the

bigger the the DMX value, the

smaller the beam angle

Dimmer

Mode

Red Dimmer

Red dimmer (0-100%)

Green

Dimmer

Green dimmer (0-100%)

Blue

Dimmer

Blue dimmer (0-100%)

White

Dimmer

White dimmer (0-100%)

Strobe

Strobe speed (slow to fast)

Zoom

Beam angle adjust (large to

small)

Mode Setup Up/Down Instruction

Sound

Mode

Sound Mode

Select

Select the built in sound mode

Sensitivity

Select

Sensitivity adjust (low to high)

Zoom

Beam angle adjust (large to

small)

Auto

Run

Mode

Dreaming

Mode Select

Built-in dreaming mode

Jumping

Mode Select

Built-in jumping mode

Speed Set

Adjust thr speed of dreaming/

snap program mode

Zoom

Beam angle adjust (large to

small)

Static

Color

Select

Mode

Static

Colour

Select

Select 15 static colours

Strobe

Strobe speed (slow to fast)

Zoom

Beam angle adjust (large to

small)

Setup

Mode

Display on/

off

LED digital tube display always

LED digital tube display off

Display

normal/

inversed

LED digital tube display normal

LED digital tube display

inversed

Initialization

mode

Initialize the nit at the extra

factory setting

Reset mode

Reset the position of the

electric machine

Setup Menu (cont.)

DMX -512 Control Connections

This  xture complies with international USITT DMX standards and can be used

with a 3 pin DMX connector. Plug in the provided 3 pin XLR cable to the female 3

pin XLR output of your controller and the other side to the male 3 pin XLR input or

the LED MAX ZOOM QUAD. To connect the units to DMX, you must daisy chain

the  xtures together as a referred in the diagram below. Always end your DMX-512

connection with a DMX terminator.

For installations where the DMX cable has to run for a long distance, or as an

electrically noisy environment, it is recommended to use a DMX terminator. This

helps in preventing corruption of the digital control signal by electrical noise. The

DMX terminator is simply an XLR plug with a 120 resistor connected between pins

two and three, which is then plugged into the output XLR socket of the last  xture

in the chain.

Mounting And Installing

Caution: for added protection, mount the xture in areas outside walking paths,

seating areas, or in areas were the xture might be reached by unauthorized

personnel. Before mounting the xture to any surface, make sure that the

installation area can hold a minimum point load of 10 times the devices weight.

Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable. Never stand directly below the device when

mounting, removing, or servicing the xture.

Whether installing inverted on a truss or ceiling, or set on a at level surface be

sure this xture is kept at least 0.5m (1.5ft) away from any ammable materials

(decorations, etc.). Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the clamp fails.

Mounting Points:

Overhead mounting requires extensive experience, including calculating working

load limits. A knowledge of the installation material being used, and periodic safety

inspection of all installation material and the xture are all imperative and should

only be performed by a qualied technician. Improper installation can result in

bodily injury or damage.

Regardless of the rigging option you choose for your MICROH LED MAX ZOOM QUAD

xture, always be sure to secure your xture with a safety cable. The xture

provides a built-in rigging point for a safety cable hanging bracket. Be sure to only

use the designated rigging point for the safety cable and never secure a safety

cable to a carrying handle.

DMX Channel Modes

5CH Mode

Channel Value Function

1 000-255 Red dimmer (0-100%)

2 000-255 Green dimmer (0-100%)

3 000-255 Blue dimmer (0-100%)

4 000-255 White dimmer (0-100%)

5 000-255

Zoom adjust the beam angle from smallest to biggest

when set to

Zoom adjust the beam angle from biggest to smallest

when set to

6CH Mode

Channel Value Function

1 000-255 Dimmer (0-100%)

2 000-255 Red dimmer (0-100%)

3 000-255 Green dimmer (0-100%)

4 000-255 Blue dimmer (0-100%)

5 000-255 White dimmer (0-100%)

6 000-255

Zoom adjust the beam angle from smallest to biggest

when set to

Zoom adjust the beam angle from biggest to smallest

when set to

7CH Mode

Channel Value Function

1 000-255 Dimmer (0-100%)

2 000-255 Red dimmer (0-100%)

3 000-255 Green dimmer (0-100%)

4 000-255 Blue dimmer (0-100%)

5 000-255 White dimmer (0-100%)

6 000-015 No function

016-255 Strobe (slow to fast)

7 000-255

Zoom adjust the beam angle from smallest to biggest

when set to

Zoom adjust the beam angle from biggest to smallest

when set to

8CH Mode

Channel Value Function

1 000-255 Dimmer (0-100%)

2 000-255 Red dimmer (0-100%)

3 000-255 Green dimmer (0-100%)

4 000-255 Blue dimmer (0-100%)

5 000-255 White dimmer (0-100%)

016-255 Strobe (CH 2-5) (slow to fast)

000-255 Speed (CH 7) (slow to fast) (value 160-239)

000-255 Sound sensitivity (CH 7) (low to high) (value 240-255)

000-015 Mode 01: No function

016-031 Mode 02: Red

032-047 Mode 03: Green

048-063 Mode 04: Blue

064-079 Mode 05: Purple

080-095 Mode 06: Yellow

096-111 Mode 07: Cyan

112-127 Mode 08: White

128-135 Mode 09: Red fade

136-143 Mode 10: Green fade

144-151 Mode 11: Blue fade

152-159 Mode 12: White fade

160-191 Mode 13: Colour change

192-239 Mode 14: Colour strobe

240-255 Mode 15: Sound mode

000-255 Zoom adjust the beam angle from smallest to biggest

when set to

000-255 Zoom adjust the beam angle from biggest to smallest

when set to

Maintenance and Cleaning

The following points have to be considered during the inspection:

1. All screws for installing the device, or parts of the device must be tightly

connected, and must not be corroded.

2. There must not be any deformations on the housing, colour lenses,  xations or

installation spots (ceiling, suspension, trussing).

3. Mechanically moved parts must not show any traces of wearing and must not

rotate with unbalances.

4. The electric power supply cables must not show any damage, material fatigue

or sediments.

Further instructions depending on the installation spot and usage must be handled

by a skilled installer or technician. Any safety issues must be resolved.

CAUTION!

Disconnect  xture before servicing.

In order to keep the  xture in good condition and extend the life, we suggest regular

cleaning to the  xture.

1. Clean the inside and outside lens each week to avoid the light output from

darkening due to accumulation of dust, dirt, etc.

2. Clean the fan each week.

3. A detailed electrical check by an approved technician every three months is

advised. Ensure the circuit contacts are in good condition, and prevent from

overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint-free

cloth. Never use alcohol solvents.

There are no serviceable parts inside the device. Please refer to the instructions

under “Installation Instructions.”

Should you need any spare parts, please order genuine MICROH parts from your

local dealer.

CAUTION!

Take care using this equipment! High voltage risk of electric shock!

PLEASE NOTE:

All information for this product is subject to change without notice!

For more information please contact:

www.microhpro.com

[email protected]

905.428.9062

Microh LED Max Zoom AW User manual

Brand: Microh

Model: LED Max Zoom AW

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

LED MAX ZOOM QUAD

Download PDF

report

Microh LED Max Zoom AW User manual

This manual is also suitable for

Microh LED Max Zoom AW User manual

Related papers

Other documents