Page is loading ...
Project __________________________________
Item ____________________________________
Quantity ________________________________
CSI Section 11400
Approved _______________________________
Date ____________________________________
980 S. Isabella Rd.
Mt. Pleasant, Michigan 48858
Phone: 800-733-8948 or 989-773-7981
Fax: 800-669-0619
www.delfield.com
Shelleymatic
®
by Deleld
Cabinet top surface shall be 22-gauge stainless steel. Insulated
folding lid shall be stainless steel with high impact plastic liner
and have chrome plated, die cast handles. Opening shall have
a throat liner constructed of high impact plastic.
The exterior sides shall be 20-gauge stainless steel. The
watertight inner liner shall be 22-gauge stainless steel. The
unit shall be insulated with foamed-in-place high density
environmentally friendly, Kyoto Protocol Compliant, Non
ODP (Ozone Depletion Potential), Non GWP (Global Warming
Potential) polyurethane.
Refrigeration system will be controlled by an electronic control
with built in defrost timer. System will also include a blower
coil and a 1.00" (2.5cm) I.P.S drain. Unit designed to maintain a
temperature setting from -5ºF to 40ºF (-21ºC to 4ºC).
The Following Applies To Models CPB-2 And CPB-4 Only:
Stainless steel perforated dispenser tubes (2 on CPB-2 and 4 on
CPB-4) for plates shall be furnished with properly calibrated,
non-fatiguing stainless steel springs. Each dispenser tube shall
have a maximum capacity of approximately 50 plates.
NOTE: The maximum dish diameter that can be dispensed by
these models is 9.62" (24.4cm).
The Following Applies To Model CMB-2 Only:
Self-leveling mechanism to be field adjustable by adding or
removing stainless steel extension springs on perimeter of
vertical side channels. A 20.00" x 20.00" (50.8cm x 50.8cm)
carrier tray shall be provided. The dispenser shall have a
capacity of three to four 20" x 20" racks (50.8cm x 50.8cm).
Racks are not supplied by Delfield; must hold 20-25 mugs.
Specifications
Standard Features
Options &
Accessories
Cabinet top to be 16-gauge stainless steel with
all corners welded, polished and reinforced
Exterior sides and watertight interior shall be
22-gauge stainless steel
(4) 4.00” diameter polyolefin swivel casters
(all locking)
Non-marring gray corner bumpers
Insulated folding lid, stainless steel and high
impact plastic
Opening throat liner to be high impact plastic
Refrigeration system controlled by an
electronic control with built-in defrost timer,
blower coil and condensate evaporator
8’ cord and plug supplied
Maintains -5°F to 40°F (-21°C to 4°C)
Environmentally friendly HFC-404A refrigerant
One year parts and 90 day labor standard
warranty
CP-2 and CP-4 SERIES ONLY
Stainless steel perforated dispenser tube
Properly calibrated, non-fatiguing stainless
•
•
•
•
•
•
•
•
•
•
•
•
•
CMB-2 Chilled mug dispenser, accommodates approximately 60 mugs
CPB-2 Chilled plate dispenser, accommodates approximately 100 plates
CPB-4 Chilled plate dispenser, accommodates approximately 200 plates
•
•
•
Models
CMB/CPB
Built in chilled mug and plate dispensers
CMB/CPB: Built in chilled mug and plate dispensers
steel springs
Maximum capacity of 50 plates,
maximum diameter is 9.62”
CM-2 SERIES ONLY
Self-leveling mechanism to be field
adjustable by adding or removing
springs
20” x 20” carrier tray shall be provided
Dispenser shall have capacity for three
to four 20” x 20” racks
Racks not supplied by Delfield
Lid-locking device (specify model
number)
Special voltages (consult factory)
•
•
•
•
•
•
•
CMB-2
980 S. Isabella Rd.
Mt. Pleasant, Michigan 48858
Phone: 800-733-8948 or 989-773-7981
Fax: 800-669-0619
www.delfield.com
Shelleymatic
®
by Deleld
CMB/CPB
Built in chilled mug and plate dispensers
Printed in the U.S.A.
DSCMB
11/09
Deleld reserves the right to make changes to the design or specications without prior notice.
Plan View
CMB-2
Elevation View
CMB-2
Plan View
CPB-2
Plan View
CPB-4
Elevation View
CPB-2
Elevation View
CPB-4
Counter Installation Detail
Right End View
CMB-2
Right End View
CPB-2 & CPB-4
Throat
Liner
Cutout
dimensions in
counter top are
shown in the
specications
table
27.75"
70cm
29.68"
75cm
47.50"
121cm
27.50"
70cm
20.62"
52cm
1.62"
4cm
32.00"
81cm
27.43"
70cm
17.25"
44cm
1.87"
5cm
13.12"
33cm
2.40"
6cm
MAX
9.62"
24cm
23.12"
59cm
27.43"
70cm
17.37"
44cm
1.62"
4cm
13.12"
33cm
2.15"
5cm
MAX
9.62"
24cm
23.12"
59cm
47.50"
121cm
Lids ad 1.75"
(4cm) to height
Lids ad 1.75"
(4cm) to height
Lids ad 1.75"
(4cm) to height
47.68"
121cm
32.18"
82cm
47.68"
121cm
NOTE: On
CPB models,
leave a 2.12"
(5.4cm) space
between the
two cutouts
Counter top
27.68"
70cm
29.69"
75cm
Specifications
Model Approximate
Capacity
Counter Top Cutout
Dimensions
Electrical
Connection
H.P. Amps Nema
Plug
Ship Weight
CMB-2 60 mugs 22.25" x 25.25"
(57cm x 64cm)
120V/60Hz/1Ph 1/3 10.0 5-15P 385lbs - 175kg
CPB-2 100 plates or
bases
(1) 13.37" x 23.25"
(34cm x 59cm)
120V/60Hz/1Ph 1/3 10.0 5-15P 360lbs - 163kg
CPB-4 200 plates or
bases
(2)13.37" x 23.25"
(34cm x 59cm)
with 2.12" (5cm) space
between cutouts
120V/60Hz/1Ph 1/3 10.0 5-15P 385lbs - 175kg
The following information is required with an order to ensure proper operation of CPB-2 and CPB-4 models:
1) Height of one plate
2) Overall diameter of the plate
3) Height of a stack of eleven plates
4) Weight of a stack of 10 plates
/
