Kathrein UFG 300 Technical data

Page is loading ...

UFG 300

20610082

Q

LCD display with 4 lines and 20 characters per line for

display of the settings and operating parameters

Q

12 ergonomically arranged function buttons with rub-proof

labelling for entering the channel unit parameters

Q

Numeric characters can be input directly

Q

Spiral cable, 1.4 m long, non-kinking, 6-pin mini DIN plug

for connection to modules

Q

USB interface for software-update via PC

Q

Power supply (5 V/100 mA) to controller via modules

Q

Complies with: EN 50083-2 and RoHS conformity

Q

Dimensions without cable (mm): 220 x 75 x 25

Q

Packing unit/weight (pc./kg): 1/0.6

UFO

®

compact signal processing system

Controller

UFG 300 20610082

Intelligent manual control unit for programming the standard

setting parameters of the UFO

®

compact modules.

Controller

Keypad

USB port

DisplayMini DIN plug

Type

Order no.

Power consumption

(mA)

Power supply

(V)

Housing protection

class

Permissible ambient temperature

range (°C)

UFG 300

20610082

100 5 IP 50 to EN 60529 +5 to +50

1 Explanation of the keypad

Increase value

Decrease value

Next parameter

Previous parameter

Next channel unit

Previous channel unit

Sub-menu

Save all parameter

values

Help text for the currently selected parameter

Display the software versions of the controller

and channel unit, or move the cursor to the left in

numeric input mode

Changing the edit mode:

1. Press - Change into numeric input mode

2. Press - Load the input and exit numeric

input mode

System menu:

- Language setting

- Special functions (cable NIT)

The numbers, letters and special characters

assigned to a button are printed on the

button or below the button on the housing.

2 Commissioning

Q

Set the coding nib of the mini-DIN plug to the left

Q

Plug the mini-DIN connector into the UFO

®

compact channel

unit socket marked “PRG”

Q

The controller’s power supply comes via the module or from

a UFX 312 or UFX 314 data bus demultiplexer if one is used.

936.3627/-/1109/1.7e

Note:

The most up-to-date version of these user instructions

can be found on the Kathrein homepage under

“www.kathrein.de → Service → Operating manuals”

3 Operating notes

The parameter currently selected with the buttons and ﬂ ashes on the display.

The setting of the desired value is performed stepwise via the buttons and or by inputting numeric characters using the

button (see section 4).

Select or exit a sub-menu using the button.

On the display, the symbol ﬂ ashes if there is a sub-menu available for the selected parameter.

If the controller is disconnected from the UFO

®

compact module without saving the settings by pressing the button, the

settings originally stored in the module are restored.

Note:

The module-speciﬁ c setting instructions are included with the instructions for the respective UFO

®

compact module.

Remark:

The instructions include stickers with button explanations in English, French and Spanish.

These can be applied over the German stickers on the back of the device.

4 Direct input of numeric parameter values

Q

Pressing the button takes you into direct input mode

a) decimal parameter values

Q

The numeric keypad can be used to input the numbers 0... 9 at the currently selected position. Every time a number

is input, the input position shifts one place to the right

Q

Pressing the button shifts the input position one place to the left

b) hexadecimal parameter values (identiﬁ ed with the letter “h”)

Q

The and buttons can be used to input the hexadecimal numbers 0... 9, A-F at the currently selected position

Q

Pressing the and buttons shifts the input position one place to the left or right

Q

Pressing the button again exits direct input mode and the input value is loaded

936.3627/-/1109/2.7e

The following instructions apply to numeric input ﬁ elds. Direct input can be used to input numeric values place by place.

During this, the current input position for inputting a numeric value ﬂ ashes.

5 Inputting alphanumeric parameter values

Alphanumeric parameter values are input using a virtual keyboard, which appears on the display when the menu button is

pressed:

Q

The and buttons allow the cursor position to be changed

Q

The character is chosen using the button

Q

A character already inserted is deleted using the button

Q

Pressing the again exits input mode

6 Interrogating the version numbers

Q

Press the button

Q

The button allows you to page through the overview of the version numbers

936.3627/-/1109/3.7e

7 Settings at system level

7.2 Settings for compiling the cable NIT

A UFX 312 or UFX 314 (BN 20610071) data bus de-multiplexer is required for compiling the cable NIT.

The “Cable NIT” entry in the system menu can be selected only if the central controller is connected to a demultiplexer

(control port).

Pressing the “ ” button brings you to the system menu, where the cable NIT settings can be made. Press the “ ” and “ ”

“Cable NIT” buttons in the system menu.

Pressing the “Sub-menu” button activates the sub-menu; pressing the “Sub-menu” button again deactivates it.

**** System ****

Cable NIT

Selection with +/-

System menu “Cable NIT” sub-menu

**** Cable NIT ****

NIT: Off Compile

Network:

Name ID

Press the “ ” and “ ” buttons to select the desired parameter “Off/On”, “Compile”, “Name” or “ID”.

Press the “Sub-menu” button to activate the selected parameter and open the respective sub-menu.

**** System ****

Set language

Selection with +/-

System menu “Set language” sub-menu

**** Language settings ****

English

The central controller is selected by pressing the double arrow buttons “ ” and “ ”. The procedure is exactly the same as for

the channel units; when selected the controller has the same priority as a channel unit.

7.1 Setting the language

Pressing the “ ” button brings you to the system menu, where the language can be set and the version numbers interrogated,

the system password set and the cable NIT settings made.

The instructions for this can be found at the start of the setup instructions, since these menus are accessible at the

channel unit level and relevant to it.

936.3627/-/1109/4.7e

“Cable NIT” sub-menu

**** Cable NIT ****

NIT: Off

Compile

Network: Name ID

“Cable NIT” sub-menu (display during NIT compilation)

Cable NIT

being compiled

Please wait

□ □ □ □ ...

A B C E D E F G H I J K L M N O P Q R

S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9 _

KATHREIN WERKE KG _

“Name” sub-menu “ID” sub-menu

Network ID

FF 01

7.2.1 Setting the name and the network ID for the cable NIT

Press the “ ” and “ ” buttons to select the desired parameter “on”, “Compile”, “Name” or “ID”.

Press the “Sub-menu” button to activate the selected parameter and open the respective sub-menu.

The network name is set by adding “ ” or removing “ ” characters at the ﬂ ashing cursor in the third (name) line.

The character to be added is selected by using the “ ” and “ ” buttons to move the cursor within the ﬁ rst two lines.

The maximum number of characters is 40.

Exit the menu by pressing the “Sub-menu” button ; this saves the set value.

The network ID should only be set if the operator applied for and was granted the ID by the ETSI.

The preset value (FF01) is intended for networks without a speciﬁ c network ID.

The network ID is selected digit by digit using the “ ” and “ ” buttons and is changed using the “ ” and “ ” buttons.

Exit the menu by pressing the “Sub-menu” button ; this saves the set value.

7.2.2 Compiling the cable NIT, switching the cable NIT on and off

The controller carries the NIT compilation process through to completion after it has been started manually with the “ ” or

“ ” button. The new cable NIT is created and then sent to the channel units. The procedure can be aborted by pressing the

“ ” button (leading to the error message shown below). A progress bar is displayed in the bottom line of the display during the

compilation process.

When the cable NIT is complete it is saved and can now be switched on and off as required. To do this, use the “ ” and “ ”

buttons to select the “Cable NIT” “on/off” sub-menu and use the “ ” and “ ” to make the change-over.

“Cable NIT” sub-menu

**** Cable NIT ****

NIT:

On

Compile

Network: Surname ID

“Cable NIT” sub-menu (display if aborted)

NIT error:

User abort

<Continue: key >

The following error messages may appear during cable NIT compilation:

“Cable NIT” sub-menu

NIT error

Not all channel

units registered

< Continue: key >

“Cable NIT” sub-menu

NIT error:

Insert position speciﬁ -

cation non-compliance

< Continue: key >

936.3627/-/1109/5.7e

a) Compilation with an input distributor row

b) Two polarisations

z.B. UFO390

z.B. Astra H

z.B. UFO 370

z.B. UFO390

A

z.B. Astra H

z.B. UFO390

z.B. Astra V

z.B. UFO 370

z.B. UFO390

AB

The following conditions must be fulﬁ lled to compile the NIT successfully:

● The system must be fully set up

● All digital channel units must be in operation with their front ends clicked into place

7.2.3 Planning a system with cable NIT

When planning a system with cable NIT, the following should be noted regarding the position of the modules:

Case 1: All modules in use control the functioning of the cable NIT.

In this case the position of the individual modules in the system is immaterial and irrelevant.

Case 2: UFO

®

compact system made up of different module types

If not all the modules in use are capable of compiling a cable NIT, the insert position speciﬁ cation described

below must be complied with.

Insert position speciﬁ cation:

For NIT compilation to function properly, each SAT level must be reached by at least one channel unit that is capable of

compiling an NIT.

c) Two input distributor rows, several polarisations (with option UFS 340)

A

z.B. Astra H

zu Ein

g

än

g

en A

z.B. UFO390

z.B. UFO 370

z.B. UFO390

z.B. UFO 370

z.B. UFO390

B

zu Ein

g

än

g

en A zu Ein

g

än

g

en A

z.B. Eutels. H

B

z.B. Astra

zu Ein

g

än

g

en B

B

zu Ein

g

än

g

en B

B

z.B. Eutels. V

zu Ein

g

än

g

en B

Note:

The cable NIT can be used only on

transponders that are ﬁ tted with an

NIT-compilation-capable channel unit.

Note: The NIT compilation cannot be performed if the HF output signal is switched on at an unused channel unit.

e.g. UFO 371/TP

e.g. UFO 390

e.g. Astra H

e.g. Astra V

e.g. UFO 371/TP

e.g. UFO 390

e.g. Astra H

e.g. Astra

e.g. Eutels. H

e.g. Eutels. V

to inputs A

to inputs A to inputs A

to inputs B to inputs B to inputs B

8.2 Programming the ﬁ rmware (software update)

• Preconditions:

a) PC/laptop with the following system requirements:

• USB port

• Operating system Windows 2000 or Windows XP

• Installed USB driver for UFG 300 (see section 7.3)

• Administrator rights for installation of the USB driver for UFG 300

b) USB cable

c)

PC software “Bootload.exe” with version 2.10 or higher

• Update procedure:

a) Use the USB cable to connect the free USB interface on the PC to the USB interface on the UFO

®

compact controller

b) Install the USB driver for UFG 300 on the PC, if this has not previously been done (see section 7.3)

The following steps refer to the Windows update software “bootload.exe”:

c) Start “bootload.exe”

d) Press “setup”

e) Select the COM port chosen in step j) in section 7.3

f) Press “Select ﬁ le”

g) Select ﬁ rmware “setup.bin”

h) Press “Open”

i) Press “Download”. This starts the software update

j)

The update procedure is completed when the progress display disappears and the message “Start application” appears.

8 Software Update

8.1 General Information

The software for the UFO

®

compact controller consists of two components:

a) Bootloader: software for exchanging the ﬁ rmware

b) Firmware: software for conﬁ guration of UFO

®

compact channel units

The ﬁ rmware can be exchanged using a PC programme (“bootload.exe”).

Important note:

No connection to the UFO

®

compact system is necessary to perform a software update.

Power is provided by the USB interface.

936.3627/-/1109/6.7e

8.3 Installation of the USB driver for the UFG 300

Installation under Windows XP is shown as an example. Installation under Windows 2000 is similar.

a) Log in as a Windows user with administrator rights

b) Unzip the file with the USB driver (e.g. “CDM 2.00.00.zip”) into a suitable directory

c) Use the USB cable to connect the free USB interface on the PC to the USB interface on the UFO

®

compact controller

d) Wait until the Windows wizard for installation of new hardware appears

e) Open the dialogue “Create connection with Windows Update”

- Select the following choices:

“Should a connection with Windows Update be created to search for software?”

“No, no this time”

- Press “Continue”

Electronic equipment is not household waste - it must be disposed of properly in accordance with Directive 2002/96/EC OF

THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27

th

January 2003 on waste electrical and electronic equipment

(WEEE). At the end of its service life, take this device for disposal at a designated public collection point.

Internet: www.kathrein.de

KATHREIN-Werke KG • phone +49 8031 184-0 • Fax +49 8031 184-306 • Anton-Kathrein-Straße 1 - 3 • P.O. Box 100 144 • 83004 Rosenheim GERMANY

936.3627/-/1109/7.7e/ZWT Technical data subject to change.

9 Warning and safety notes

• The LCD display is fragile and can be damaged if the unit is dropped.

• Do not kink the cable!

• Plug the mini DIN-plug only into UFO

®

compact channel units

• Do not open the unit!

f) Dialogue “Selection of the Installation Source”

- Select the following choices:

“How do you wish to proceed?”

“Install software from a list or from a specific source”

- Press “Continue”

g) Dialogue “Search and Installation Options”

- Select “Search these sources for the most appropriate driver”

- Deactivate “Search interchangeable media”

- Activate “Search the following source also”

- Press “Search”

- Select the directory holding the USB driver from step a)

- Press “OK”

- Press “Continue”

h) Dialogue “Finish the Wizard”

- Press “Finish”

i) If steps e) to h) have already been run through twice, continue with step j).

Otherwise repeat steps e) to h) once again

Note: The required “USB Serial Port” driver will not be installed until the second pass

j) Check that the USB driver for the UFG 300 has been correctly installed.

This is done by starting the Windows Device Manager as follows:

- Call up the Control Panel by “Start → Settings → Control Panel”

- Start the “System” applet

- Select the “Hardware” tab

- Press “Device Manager”

An entry “USB Serial Port” must appear under both “COM” and “LPT” connections, followed by the name of a COM Port.

Make a note of the COM Port, since you will need to enter it later in step e) when programming the ﬁ rmware.

If no entries are shown:

- Close the Device Manager again

- Break the USB connection between the controller and the PC

- Wait a few seconds and then re-establish the USB connection between the controller and the PC

- Start the Device Manager and, as described above, once again search for the “USB Serial Port” entry

Page is loading ...

Kathrein UFG 300 Technical data

Kathrein UFG 300 Technical data

in other languages

Related papers

Other documents