Minka-Lavery 2368-77 User manual

Minka-Lavery
Brand
Minka-Lavery
Model
2368-77
Type
User manual
Fig.1
INSTALLATION INSTRUCTIONS
Item#2368-77(New.09/14/2017)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 2
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture
including the mounting hardware.
3. Position the mounting plate (B) on the ceiling and mark the
location of the two drywall anchors(C).Then insert the drywall
anchors(c) into the ceiling.
4. Attached mounting plate (B) to the outlet box using mounting
screws(E)( size:8/32*25mm) and wood screws(D) into drywall
anchors(C).The side of mounting plate marked “GND” must face
out.
5. Determine the desired handing height and thread rods (I2,I3) to
the nipple(J) of the fixture body, Then attach loop(H)by screwing
in to rod(I1).Note: remove the nipple if installing with one 6’ rod
only.
6. Attach the quick link (O) to loop (H) and loop on the canopy,
carefully feed the wire over loop (I1),quick link(O) and loop on
the canopy.
7. The support cable (M) is provided to support the weight of the
fixture while wiring. Align the fixture to mounting plate(B) and
attach hook(L) on the end of support cable(M) into a slot located
on mounting plate(B).Carefully allow the support cable(M) to
support the weight of the fixture while wiring.
CONNECTING THE WIRES (Fig. 2)
8. At this point, connect the electrical wires as shown in (Fig.2),
Make sure that all wire connections are secured. If your outlet
has a ground wire (green or bare copper), connect the fixtures
Ground Wire to it. Otherwise, connect the fixture Ground Wire
directly to the crossbar using the Green Screw.
INSTALL LIGHT BULB (Fig. 1)
9. Install light bulb (K) (not included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!!) (NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
FINISH THE INSTALLATION (Fig. 1)
10. Your installation is complete now. Return power to the junction
box and test the fixture. Note: Illustration (Fig.1) on this manual is
for installation purposes only. It may or may not be identical to
the fixture purchased.
2368-77
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
M
I1
I3
O
G
F
K
B
A
I2
H
J
E
D
C
- Set #A-022-295135
- Mounting plate
-Ground Screw
-Mounting Screw*2
Rod#W30-H-077*2 (I1)
W30-1-077*6 (I2)
22*110
3pcs
22*22
B
1pc
22*22
4pcs
22*90
1pc
  • Page 1 1

Minka-Lavery 2368-77 User manual

Minka-Lavery
Brand
Minka-Lavery
Model
2368-77
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents