Broan C7B(A,H)M0 Installation guide

Brand: Broan

Model: C7B(A,H)M0

Type: Installation guide

C7 Series Split System Uncased Indoor Coils

INSTALLATION INSTRUCTIONS

IMPORTANT

ATTENTION INSTALLERS:

It is your responsibility to know this product better than your customer. This includes being

able to install the product according to strict safety guidelines and instructing the customer on

how to operate and maintain the equipment for the life of the product. Safety should always be

the deciding factor when installing this product and using common sense plays an important

role as well. Pay attention to all safety warnings and any other special notes highlighted in the

manual. Improper installation of the furnace or failure to follow safety warnings could result in

serious injury, death, or property damage.

These instructions are primarily intended to assist qualiﬁed individuals experienced in the proper

installation of this appliance. Some local codes require licensed installation/service personnel

for this type of equipment. Please read all instructions carefully before starting the installation.

Return these instructions to the customer’s package for future reference.

DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are

used frequently throughout this manual to designate a

degree or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation that

if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

WARNING:

This unit must be installed in accordance

with the instructions outlined in this manual

during the installation, service, and operation

of this unit. Unqualiﬁed individuals should

not attempt to interpret these instructions or

install this equipment. If you do not posses

mechanical skills or tools, call your local dealer

for assistance. Under no circumstances should

the equipment owner attempt to install and/or

service this equipment. Failure to follow safety

recommendations could result in possible

damage to the equipment, serious personal

injury or death.

• The installer must comply with all local codes and

regulations which govern the installation of this type

of equipment. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Consult local building codes for

special installation requirements.

• Familiarizeyourselfwiththecontrolsthatshutoffthe

electrical power to the unit. If the unit needs to be shut

down for an extended period of time, turn off electrical

power at the circuit breaker. For your safety always

turn off the electrical power before performing service

or maintenance on the unit.

• Installationofequipmentmayrequirebrazingoperations.

Installer must comply with safety codes and wear

appropriate safety equipment (safety glasses, work

gloves, ﬁre extinguisher, etc.) when performing brazing

operations.

• Read the Installation Instructions supplied with the

furnace or air handler. Always observe all safety

requirements outlined in this manual and on the furnace

or air handler markings before installing the coil.

• Follow all precautions in the literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

WARNING:

C7 coils are pressurized with Nitrogen at the

factory. Avoid direct face exposure or contact

with valve when gas is escaping. Always ensure

adequate ventilation is present during the

depressurization process. Any uncertainties

should be addressed before proceeding.

NITROGEN

HEALTH

FLAMMABILITY

REACTIVITY

0 Minimal Hazard

1 Slight Hazard

WARNING:

Improper installation, service, adjustment, or

maintenance may cause explosion, ﬁre, electrical

shock or other hazardous conditions which may

result in personal injury or property damage.

Unless otherwise noted in these instructions,

only factory authorized kits or accessories may

be used with this product.

WARNING:

PROPOSITION 65 WARNING: This product

contains chemicals known to the state of

California to cause cancer, birth defects or other

reproductive harm.

GENERAL INFORMATION

C7 Series uncased indoor coils are designed for upﬂow,

downﬂow, or horizontal applications and are equipped with

braze type refrigerant connections for easy installation.

• IfaTXVisnotinstalledbutrequiredforyourapplication,

seeTable1(page7)todeterminetheproperkitbased

on tonnage and refrigerant type of the unit.

• Checkthecoilsoricesizeandconrmthatit’ssuitable

for application with the intended outdoor unit. Depending

on application, additional installer supplied oriﬁce or

TXVmayberequired.

• Optional cooling/heating equipment must be

properly sized and installed in accordance with the

furnace manufacturer’s specications and approved

recommendations.

• “HeatingOnly”furnaceaircirculatorsmayhavetobe

replacedwithmulti-speedHeating/Coolingblowers

to upgrade the air delivery (CFM) when an add-on

coilisinstalled.RefertoTables2&3(page7)forcoil

specications,recommendedCFM,andallowancesfor

pressure drop across the coil and ﬁlters.

• Verifythattheairdeliveryofthefurnace/airhandleris

adequate to handle the static pressure drop of the coil,

ﬁlter, and duct work.

• Ifpreciseformingofrefrigerantlinesisrequired,acopper

tubing bender is recommended. Avoid sharp bends and

contact of the refrigerant lines with metal surfaces.

• Refrigerant lines should be wrapped with pressure

sensitive neoprene or other suitable material where

they pass against sharply edged sheet metal.

• Horizontalinstallationsrequireahorizontaldrainpan

kittobeinstalled.SeeTables2&3foravailablepart

numbers.

• Close-off plates are available in some air lter kits.

RefertotheReplacementPartsListforavailablepart

numbers. Install the necessary close-off plates around

the refrigerant lines and drain line where required.

Reinstallallinnerandouterpanelsofthefurnace/air

handler that were previously removed when installing

the indoor coil.

COIL INSTALLATION

WARNING:

ELECTRICAL SHOCK, FIRE OR

EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

 

to the unit.

 

to disconnecting. Reconnect wires correctly.

 

CAUTION:

The coil must be level to ensure proper

condensate drainage. An unlevel installation may

result in structural damage, premature equipment

failure, or possible personal injury.

NOTE TO INSTALLER: C7 Coils are not factory charged

with refrigerant. It will be necessary to evacuate the indoor

coiland lineset prior tocharging. Refer tothe outdoor

unit installation manual for detailed charging instructions.

Upﬂow Installations

1.Disconnectallelectricalpowertothefurnace.

2. Install the coil case on the furnace air discharge opening

and level it as needed to ensure proper condensate

drainage. If needed, make a plate to adapt the coil to

theairdischargeopening.SeeFigure5(page6)for

coil dimensions.

3.Makeandinstalltheplenumoverthecoil.Insulateas

required.

4. Seal the enclosure as required to minimize air leakage.

5.Connect the refrigerant lines as outlined in the

RefrigerantLineConnectionsection.

Downﬂow Installations

C7 coils may be installed in downﬂow applications. It is

required that the furnace and coil cabinets are securely

mounted together before setting in place. Fossil fuel

applications require the coil to be placed in the supply

air stream only.

Horizontal Installations

C7 coils can be installed horizontally, but it is required that

the furnace and coil cabinets be securely mounted together

before setting in place. A horizontal drain pan kit must

alsobeinstalledunderthefurnaceorairhandler.Refer

totheReplacementPartsListforavailablepartnumbers.

Suction

Line

Liquid

Line

Cap

Schrader

Valve

Figure 1. Suction & Liquid Line Locations

Figure 2. 

Install restrictor with

rounded end down

in the distributor

Figure 4. 

Figure 3. Removal of Oriﬁce

Carefully remove the

restrictor orifice from

the distributor body

Refrigerant Line Connections

System Depressurization

1.Removethecap(Figure1)fromtheendoftheliquid

line.

2.VerifypressurizationbydepressingtheSchradervalve

on the end of the liquid line. Listen for any escaping gas.

If there is no pressure, test the coil for leakage.

• Ifleakageisfound,clearlymarkthelocationofthe

leak and return the coil to the distributor for processing.

• Ifnoleaksarefound,thecoilmaybeinstalled.

3. Depress the valve to relieve all pressure from the coil.

4.Remove and discard the valve core and valve core

holder on the liquid line.

5.Removetherubberplugfromthesuctionline.

OriceRemoval&Installation

NOTE: Before proceeding, perform steps 1 - 3 in the

System Depressurization section and conﬁrm that the

restrictor oriﬁce size meets the requirements outlined

intheoutdoorunitinstallationmanual.Factorysupplied

oricesizesarelistedinTable2(page7).Iftheorice

mustbereplaced,followsteps1-5.

CAUTION:

To prevent damage to the unit or internal

components, it is recommended that two

wrenches be used when loosening or tightening

nuts. Do not over tighten!

1.Usingtwowrenches,loosenthenutanddistributorbody

asshowninFigure2.Turntheassemblynutcounter-

clock-wise until the oriﬁce body halves are seperated.

2. Insert a light-gauge wire hook between the distributor

body and the restrictor oriﬁce while being careful not

to scratch either part. Carefully remove the restrictor

oricefromthedistributorbody.SeeFigure3.

3.Check the actual sizeof theneworice.The sizeis

stamped on its side. Do not use pin gauges to measure

the oriﬁce diameter.

4. Insert the new oriﬁce into the distributor body, rounded

enddown.SeeFigure4.

CAUTION:

To prevent damage to the unit or internal

components, it is recommended that two

wrenches be used when loosening or tightening

nuts. Do not over tighten!

5.Realigntheassemblynutonthedistributorbodyand

hand tighten both components. Mark a line on both

bodiesandthentightenanadditional1/4turnusingtwo

wrenches.Themovementofthetwolineswillshowhow

much the nut is tightened. If a torque wrench is used,

tightento10-12ft.lbs.or14-16Nm.

Connecting the Linesets

NOTE:IfinstallingaTXV,pleasefollowtheinstructions

suppliedwiththekit.SeeTable1 (page 7) for kit part

numbers.

1.Routeand cut both lineset tubestoproperlengthin

accordancewiththeoutdoorunitspecications.Verify

the ends are round, clean, and free of any burrs.

2. Connect the suction and liquid lineset tubes.

CAUTION:

It is recommended that a wet rag be wrapped

around the suction line in front of the close

off plate before applying heat. Failure to keep

components cool during brazing may result in

structural damage, premature equipment failure,

or possible personal injury.

3. Braze the individual connections with dry nitrogen ﬂowing

throughthejoints.Thiswillpreventinternaloxidation

and scaling from occurring.

IMPORTANT: To prevent internal oxidation and

scaling from occuring, braze all connections with

dry nitrogen ﬂowing through the joints.

4. Wrap the refrigerant lines with pressure sensitive

neoprene or other suitable material especially

where the lines enter the opening in the sheet metal.

NOTE:OnhorizontalmodelswithaTXVvalve,reposition

thesensingbulbtothe4or8o’clockpositiononthe

suction line.

Completing the Installation

1.Checkthesystemforleaks,includingthelinesetandthe

brazed joints. NOTE: Apply a soap and water solution on

each joint or union with a small paintbrush. If bubbling

is observed, the connection is not adequately sealed.

2. Evacuate the system of moisture and non-condensables

to prevent low efﬁciency operation or damage to the

unit.Thesuggestedrangeofevacuationis250-500

microns.

3. Charge the system with refrigerant. Please Refer to

the outdoor unit installation manual for additional

charging instructions.

4. Install the coil access door (if removed).

5.Properlydisposeofallremovedparts.

6.Applypowertotheunit.

Condensate Drain

CAUTION:

The coil must be level to ensure proper condensate

drainage. Improper condensate disposal may

result in structural damage, premature equipment

failure, or possible personal injury.

• Methodsfordisposingofcondensatevaryaccording

tolocalcodes.Refertolocalcodesorauthorityhaving

jurisidiction for restrictions and proper condensate

disposal requirements.

• Allcondensatepanshaveprimaryandsecondarydrain

connectionstomeetFHArequirements.Iftheapplication

is located in or above a living space where damage

mayresultfromcondensateoverow,aseparate3/4

inch drain must be provided from the secondary drain

connection and a secondary drain pan must be installed

undertheentireunit.Runsecondarydrainlinestoa

place where they are noticeable if used.

• Thecoilcondensatepanisdesignedwith3/4”NPSC

drainconnections.UseaPVCorsimilarmaterialtting

to attach the drain line to the pan. NOTE:Thetting

should be hand tightened only. Overtightening may

crack the drain pan and cause condensate to leak.

• The drain pan MUST be drained with eld supplied

tubing and looped to form a trap.

IMPORTANT: Failure to install a trap may result in

condensation overﬂowing the drain pan, resulting in

substantial water damage to surrounding area.

• Primethetrapwithwater.Insulatethedrainifitislocated

in an unconditioned space, and test the condensate line

for leaks. Consult local codes for additional restrictions

or precautions.

• Routethelinestoasuitabledrain,avoidingsharpbends

andpinchingofthelines.Thedrainshouldmaintaina

minimum horizontal slope in the direction of discharge

ofnolessthan1”verticalforevery10ftofhorizontal

run.

• During system checkout, inspect the drain line and

connections to verify proper condensate drainage.

Air Filter

Air ﬁlters are not supplied as an integral part of this

coil; however, an air lter kit is available. Refer to the

ReplacementPartsListforavailablepartnumbers.

The lter must be installed upstream of the coil and

inspected frequently. When the ﬁlter becomes clogged

with dust or lint, it should be replaced (disposable type)

or cleaned (washable type). It is recommended that ﬁlters

be inspected and replaced at least twice during the year.

Generally it is best to replace or clean the ﬁlters at the

start of each heating and cooling season.



WARNING:

ELECTRICAL SHOCK, FIRE OR EXPLOSION

HAZARD

Failure to follow safety warnings exactly could

result in serious injury or property damage.

Improper servicing could result in dangerous

operation, serious injury, death or property

damage.

 

to the furnace or air handler.

 

to disconnecting. Reconnect wires correctly.

 

CAUTION:

Do not operate the system without a suitable ﬁlter

in the return air duct system. Always replace the

ﬁlter with the same size and type.

Toensureoptimumperformanceandtominimizepossible

equipment failure, the following maintenance tasks should

be performed periodically on this equipment:

1.Theairlterinstalledwiththesystemshouldbechecked

and cleaned or replaced twice per year.

2. Check the coil, drain pan, and condensate drain line

for cleanliness at the start of each heating and cooling

season. Clean as needed.

Figure 5. 

2 1/2

3 1/8

19 1/2

3 1/8

2 1/2

19 1/2

TXV

Figure 6. 

01824A 03036A    030C 03648C 048C 060C 042D 048D 060D

NomiNal CapaCity, miN BtUH 18,000 30,000 18,000 30,000 36,000

30,000

36,000

48,000 60,000 42,000 48,000 60,000

NomiNal CapaCity, max BtUH 24,000 36,000 24,000 36,000 42,000 48,000

iNstalled orifiCe size (iN.) .048 .061 .055 .067 .071 .061 .067 .077 .083 .071 .077 .083

NomiNal airflow, miN (Cfm) 800 1,000 800 1,000 1,200

1,000

1,200

1,600 2,000 1,400 1,600 2,000

NomiNal airflow, max (Cfm) 800 1,000 800 1,200 1,400 1,600

w - widtH (iN.) 123/4 123/4 16 16 16 191/2 191/2 191/2 191/2 23 23 23

H - HeigHt (iN.) 181/2 181/2 18 18 25 18 241/2 281/2 281/2 233/4 273/4 273/4

Hl - HeigHt of liqUid liNe (iN.) 171/2 171/2 171/2 171/2 231/2 231/2 231/2 27 27 27 27 27

Hs - HeigHt of sUCtioN liNe (iN.) 151/2 151/2 151/2 151/2 211/2 211/2 211/2 25 25 25 25 25

CoNNeCtioN - liqUid liNe 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8

CoNNeCtioN - sUCtioN liNe 3/4 3/4 3/4 3/4 7/8 7/8 7/8 7/8 7/8 7/8 7/8 7/8

HorizoNtal draiN paN Kit 920265 920265 920265 920265 920266 920265 920266 920267 920267 920267 920267 920267

Table 1. 

 

R-22

REFRIGERANT

920662A 1.5or2

920663A 2.5

920664A 3

920665A 3.5

920666A 4

920667A 5

R-410A

REFRIGERANT

920668A 1.5or2

920669A 2.5

920670A 3

920671A 3.5

920672A 4

920673A 5

Table 2. 



   

X24C-A X30C-A X36C-A    X30C-C X36C-C X42C-C X48C-C X60C-C X48C-D X60C-D

NomiNal CapaCity, BtUH

24,000 30,000 36,000 24,000 30,000 36,000 30,000 36,000 42,000 48,000 60,000 48,000 60,000

meteriNg deviCe TXV TXV TXV TXV TXV TXV TXV TXV TXV TXV TXV TXV TXV

NomiNal airflow, (Cfm) 800 1000 1000 800 1000 1200 1000 1200 1400 1600 2000 1600 2000

w - widtH (iN.) 12.75 12.75 12.75 16 16 16 19.5 19.5 19.5 19.5 19.5 23 23

H - HeigHt (iN.) 18.5 18.5 18.5 18 18 18 18 24.5 24.5 24.5 28.5 27.75 27.75

Hl - HeigHt of liqUid liNe (iN.) 17.5 17.5 17.5 17.5 17.5 17.5 23.5 23.5 23.5 23.5 27 27 27

Hs - HeigHt of sUCtioN liNe (iN.) 15.5 15.5 15.5 15.5 15.5 15.5 21.5 21.5 21.5 21.5 25 25 25

CoNNeCtioN - liqUid liNe 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8

CoNNeCtioN - sUCtioN liNe 3/4 3/4 3/4 3/4 3/4 3/4 3/4 7/8 7/8 7/8 7/8 7/8 7/8

HorizoNtal draiN paN Kit 920265 920265 920265 920265 920265 920265 920265 920266 920266 920266 920267 920267 920267

Table 3. 

NOTES:

1. Individualrestrictorsareavailablebypartnumber-PN664***(where***representsthesize).Example:664103isarestrictor0.103indiameter.

2. RefertosalesspecicationsheetsforListed/Certiedcombinationsofequipmentandrequiredaccessories.

3. XinthemodeldescriptiondesignatesfactoryinstalledTXVforR-410arefrigerant.

4. RefertothecurrentAHRIDirectoryforcertiedratingsofsplitsystems.

5. Notrequiredfor“H”horizontalreadycoils.

INSTALLER:PLEASELEAVETHESEINSTRUCTIONSWITHTHEEQUIPMENTOWNER.

709345D (Replaces709345C)

Specications&illustrationssubjecttochangewithoutnoticeorincurringobligations(05/15).

Broan C7B(A,H)M0 Installation guide

Broan C7B(A,H)M0 Installation guide

Broan C7B(A,H)M0 Installation guide

Related papers

Other documents