AEC ACM Series Installation guide

Operation and Installation Manual

ACM Series

Dehumidifying Dryers

Important! Read Carefully Before Attempting to Install or Operate Equipment

Part No. A0570044 Revision NEW Bulletin No. WH1-620

$3000

Page 2 ACM Series Dehumidifying Dryers

Write down your dehumidifying ________________ ________________

dryer serial numbers ________________ ________________

here for future reference ________________ ________________

________________ ________________

Performance figures stated in this manual are based on a standard atmosphere of 59°F

(15°C) at 29.92” Hg (1,014 millibars) at sea level, using 60 hz power. Altitude is an

important consideration when specifying dehumidifying dryers. AEC can advise you on

proper selection and sizing of systems for your operating environment.

AEC is committed to a continuing program of product improvement.

Specifications, appearance, and dimensions described in this manual

are subject to change without notice.

Part No. A0570044 Revision NEW Bulletin No. WH1-620

ACM Series Dehumidifying Dryers Page 3

Table of Contents

1 General Information ............................................................9

1-1 Models Covered .......................................................................................................... 9

1-2 Equipment Function .................................................................................................... 9

1-3 Necessary Documents ................................................................................................ 9

1-4 Standard Features..................................................................................................... 10

1-5 Options......................................................................................................................10

1-6 The Drying System.................................................................................................... 12

1-7 Specifying a Drying System ...................................................................................... 14

2 Safety..................................................................................15

2-1 Work Rules................................................................................................................15

2-2 Tools and Equipment Needed................................................................................... 15

2-3 Mechanical Installation .............................................................................................. 15

2-4 Safety Considerations ............................................................................................... 16

2-5 General Responsibility .............................................................................................. 17

2-6 Operator Responsibility ............................................................................................. 17

2-7 Maintenance Responsibility....................................................................................... 19

2-8 Safety ........................................................................................................................ 20

3 Shipping Information ........................................................23

3-1 Unpacking and Inspection ......................................................................................... 23

3-2 In the Event of Shipping Damages............................................................................ 23

3-3 If the Shipment is Not Complete................................................................................ 24

3-4 If the Shipment is Not Correct ................................................................................... 24

3-5 Returns......................................................................................................................24

4 Installation .........................................................................25

4-1 Work Rules................................................................................................................ 25

4-2 Rigging and Placing the Dryer................................................................................... 25

4-3 Making Electrical Connections .................................................................................. 28

4-4 Making Dryer/Drying Hopper Process Air Connections............................................. 28

4-5 Drying Hopper Air Trap Considerations .................................................................... 29

5 Controls..............................................................................31

5-1 Identifying Control Panel Indicator Lights and Switches for Standard Controller ...... 31

5-2 Process Air Temperature Controller.......................................................................... 33

5-3 Identifying Process Air Temperature Controller LED Indicators ................................ 34

5-4 Identifying Temperature Controller Keys................................................................... 35

5-5 Setting the Process Air Temperature ........................................................................ 35

5-6 Restoring the E5CN Temperature Controller to Factory Setup ................................. 36

5-7 Process Air Dew Point Display.................................................................................. 38

5-8 Setting the High Dew Point Alarm ............................................................................. 39

5-9 Restoring the E5CK Dew Point Meter to Factory Setup............................................ 39

5-10 Redundant Safety Controller Display ........................................................................ 40

5-11 Setting the Redundant Safety Controller................................................................... 40

5-12 Restoring the WATLOW Redundant Safety Controller to Factory Setup .................. 40

Page 4 ACM Series Dehumidifying Dryers

Table of Contents

6 Control Operation..............................................................43

6-1 Controller Operation .................................................................................................. 43

(Without Optional Alarm Horn & Reset Button) ......................................................... 43

6-2 Controller Operation .................................................................................................. 44

(With Optional Alarm Horn & Reset Button) .............................................................. 44

6-3 Alarm Display Messages........................................................................................... 46

7 Startup, Shutdown, and Operation .................................. 47

7-1 Pre-Startup Checks ................................................................................................... 47

7-2 Starting Up the Dryer................................................................................................. 47

7-3 Shutting Down the Dryer ........................................................................................... 48

8 Maintenance.......................................................................49

8-1 Work Rules................................................................................................................ 49

8-2 Servicing Process Air Filters ..................................................................................... 49

8-3 Servicing the Dew Point Monitor ............................................................................... 52

8-4 Replacing the Process Heater................................................................................... 52

9 Troubleshooting ................................................................55

10 Dryer Options ....................................................................58

11 Spare Parts ........................................................................59

11-1 Spare Parts List ............................................................................................................. 59

12 Technical Assistance........................................................61

12-1 Contact Information for Technical Assistance............................................................... 61

12-2 Returned Material Policy............................................................................................... 62

12-3 Warranty ....................................................................................................................... 63

13 Safety Tag Information .....................................................65

13-1 ACM Dryer Safety Tags ................................................................................................ 65

13-2 Dryer Identification (Serial Number) Tag...................................................................... 66

ACM Series Dehumidifying Dryers Page 5

Safety Considerations

AEC ACM Series membrane dryers are designed to provide safe

and reliable operation when installed and operated within design

specifications, following national and local safety codes.

To avoid possible personnel injury or equipment damage when

installing, operating, or maintaining this equipment, use good

judgment and follow these safe practices:

; Follow all SAFETY CODES.

; Wear SAFETY GLASSES and WORK GLOVES.

; Disconnect and/or lock out power before servicing or

maintaining the dryer.

; Use care when LOADING, UNLOADING, RIGGING, or

MOVING this equipment.

; Operate this equipment within design specifications.

; OPEN, TAG, and LOCK ALL DISCONNECTS before

working on this equipment. It is a good idea to remove the

fuses and carry them with you

; Make sure the dryer and components are properly

GROUNDED before switching on power.

; Do not jump or bypass any electrical safety control.

; Do not restore power until all tools, test equipment, etc. have

been removed and the dryer and allied equipment are fully

reassembled.

; Only PROPERLY TRAINED personnel familiar with the

information within this manual should work on this equipment.

Page 6 ACM Series Dehumidifying Dryers

AEC

“ACM” Series

Membrane Dryers

This dryer is manufactured by ACS, Inc. at the ACS-Wood Dale facility:

ACS, Inc.

801 AEC Drive

Wood Dale, IL 60191

Phone: 630.595.1060

Fax: 630.595.6641

The equipment is distributed in Europe by our European facility:

ACS-EUROPE

Daniels Industrial Estate

BATH ROAD

Stroud, Gloucestershire, England

GL5 3TJ

Phone: (44) 1453 768980

Fax: (44) 1453 768990

ACM Series Dehumidifying Dryers Page 7

Annex B Information

The following design information is provided for your reference:

1. No modifications are allowed to this equipment that could alter the CE compliance

2. Ambient temperature: 40 degrees Celsius – Maximum (104 degrees Fahrenheit)

3. Humidity range: 50% relative humidity

4. Altitude: Sea level

5. Environment: Clean, dust-free and non-explosive

6. Radiation: None

7. Vibration: Minimal, i.e. machine mounting

8. Allowable voltage fluctuation: +/- 10%

9. Allowable frequency fluctuation: Continuous +/- 1%

Intermittent +/- 2%

10. Nominal supply voltage: 460/3/60 (Verify on serial number tag)

11. Earth ground type: TN (system has one point directly earthed through

a protective conductor)

12. Power supply should include a ground connection.

13. Over-current protection is supplied in the dryer, but additional protection should be

supplied by the user.

14. The door-mounted disconnect serves as the electrical disconnect device.

15. Dryer is not equipped with local lighting.

16. Functional identification

17. Dryer is equipped with a CE mark

18. Dryer is supplied with an operating manual in the language of the destination country.

19. Cable support may be required for power cord, depending on final installation.

20. No one is required to be in the interior of the electrical enclosure during the normal

operation of the unit. Only skilled electricians should be inside the enclosure for

maintenance.

21. Doors can be opened with a screwdriver, but no keys are required.

22. Two-hand control is not required or provided.

23. All dryers should be moved around and set in a place with a lift truck or equivalent.

24. There are no frequent repetitive cycles that require manual controlrepetitive functions

are automatic while the dryer is operating.

25. An inspection report detailing the functional test is included with the dryer.

26. The machine is not equipped with cableless controls.

27. Color-coded (harmonized) power cord is sufficient for proper installation.

Page 8 ACM Series Dehumidifying Dryers

Charts and Figures

1Typical ACM Dryer Components 11

2Typical Dryer Air Flow Schematic 12

3ACM Series Machine-Mount Dimensions 13

4ACM Series Floor-Mount Dimensions 14

5A Suggested Lift Rigging for ACM Dryers (Cart Mount) 26

5B Suggested Lift Rigging for ACM Dryers (Floor Mount) 27

5C Suggested Lift Rigging for ACM Dryers (Machine Mount) 27

6Typical Control Panel 32

7Typical Temperature Controller 33

8Setting List for Process Temperature Controller 38

9Typical Dew Point Display Monitor 39

10 Typical Redundant Safety Controller Display 40

11 Setting List for Redundant Safety Controller (WATLOW) 42

12 Process Heater Location & Disassembly 53

13 Level 1 Spare Parts List (Electrical & Mechanical) 59

14 Level 2 & 3 Spare Parts List (Electrical & Mechanical) 60

ACM Series Dehumidifying Dryers Page 9

General Information 1

1-1 Models Covered

This manual provides instructions for installing and operating AEC

ACM30 and ACM60 membrane dryers. The number designation

represents air flow capacity. ACM30 models have a 30 cfm air

flow capacity, and ACM60 models have a 60 cfm capacity.

1-2 Equipment Function

AEC membrane mini dryers are designed to generate heated,

dehumidified air at carefully controlled temperatures for use in

plastic drying systems. Drying systems are sized to meet the

specific requirements stated by the purchaser at the time of

purchase.

Moisture removal from hygroscopic (moisture attracting) plastic

pellets is an essential step in the manufacture of high-quality

plastic products.

AEC dehumidifying dryers are used to generate very low dew

point air heated to a controlled temperature for drying plastic

pellets and regrind.

1-3 Necessary Documents

The documents listed below are necessary for the operation, in-

stallation, and maintenance of AEC ACM30 through ACM60

dryers. Additional copies are available from AEC, Inc.

Familiarize the appropriate personnel with these documents:

; This manual.

; The schematic and assembly drawings included in the customer

information packet.

; The Customer Parts List included in the information packet.

; Operation and installation manuals for any optional controls or

auxiliary equipment in the drying system.

Page 10 ACM Series Dehumidifying Dryers

1-4 Standard Features

; Electrical solenoid valve

; Drying temperature range of 160ºF to 400ºF.

; Mitsubishi programmable relay controller

; Display of process temperature set point and actual settings

; Process thermocouple to be connected to drying hopper air

inlet.

; Nema 12 control enclosure

• NFPA79 machinery electrical standards

• Non-fused electrical disconnect

• Branch fusing

• Mercury process heater contactor

• Regeneration temperature control

• Process high temperature alarm light

• Process/regeneration heater box

• High temperature safety system (Process/Regeneration)

1-5 Options

Options can tailor your AEC dehumidifying dryer to meet the

exact requirements of the drying task being performed.

; Process temperature up to 400ºF (or below 160ºF), including

pyrex sight glass and silicone insulated delivery hose.

; If the dryer is a central dry air generator, it will not have a

process heater box.

; Machine mount adapter to accommodate a dryer and

corresponding hopper.

; Drawer magnet, stainless steel construction.

; Casters, two (2) fixed and two (2) swivel.

ACM Series Dehumidifying Dryers Page 11

Figure 1

Typical ACM Dryer Components

Coalescing Oil

Filter

Air Filter

0.01 Micron

Solenoid

Valve

Heater Box

Membrane

Dryer

High

Temperature

Switch

Compressed

Air Inlet

Pressure

Switch

Pressure

Gage

Standard Air

Filter

Optional Dust

Collector

Page 12 ACM Series Dehumidifying Dryers

1-6 The Drying System

AEC Membrane Compressed air dryers, take a small percentage of

the dried gas and direct it back in a sweeping pattern through the

module shell. This provides a driving force to remove the moisture

with the minimum purge required.

The Moisture Vent Compressed Air Dryer, consists of thousands

of hollow-fiber membranes made of tough temperature and

pressure resistant plastic. The inside surface of these hollow fibers

is coated with an ultra-thin layer of a second plastic that performs

the actual water-vapor from air separation. This second coating

allows air to pass through it over 20,000 times easier than it allows

water to pass. As a result, moisture is expelled rapidly with very

little air loss. Two-stage drying provides the option of using the

Moisture Vent directly at the point-of-use in combination with a

refrigerated air dryer.

As a single stage unit, the dryer provides consistent performance

from 60°F to -20°F outlet dew point. When combined with a

refrigerated air dryer, the Moisture Vent system will suppress or

reduce the inlet pressure dew point to below -40°F with very low

sweep requirements.

Figure 2

Typical Dryer Air Flow Schematic

Water

Air

Purge

Dry Air

Humid Air

Dry Air

ACM Series Dehumidifying Dryers Page 13

Figure 3

ACM Series Machine-Mount Dimensions

ACM30 and ACM60 machine-mount dimensions in inches/cm

ACM30 ACM60

1.5 ft.3 Hopper

(40 liters)

3.0 ft.3 Hopper

(80 liters)

4.0 ft.3 Hopper

(120 liters)

3.0 ft.3 Hopper

(80 liters)

4.0 ft.3 Hopper

(120 liters)

6.0 ft.3 Hopper

(160 liters)

Dimension in. cm in. cm in. Cm in. cm in. cm in. cm

A 40 102 40 102 40 102 47 119 47 119 47 119

B 37.5 95 44.5 113 50.5 128 44.5 113 50.5 128 62.5 159

C225622562256256425642564

D287128712871389738973897

Mounting flange

Hopper mounting flanges on 0.75 and

can drill to match existing machine throat.

Diameter hole:

Notes:

and 1.5 cu. ft. (20 & 40 liter) hoppers

are supplied blank so the customer

3.0 cu. ft. (80 liter) hoppers and larger

are not supplied with a cast flange

(

as shown

)

.

E

F

C

A

B

D

Page 14 ACM Series Dehumidifying Dryers

Figure 4

ACM Series Floor-Mount Dimensions

ACM30 and ACM60 floor-mount dimensions in inches/cm

ACM30 ACM60

Dimension in. cm in. cm

A22 562564

B 12.75 32 12.75 32

C 15.5 39 15.5 39

D28 712871

1-7 Specifying a Drying System

Many variables were considered in the selection of your drying

system, including type of materials, residence time, throughput of

the extruder or injection molding machine. Should your operating

environment change, AEC can advise you on necessary equipment

and process time and temperature modifications required for your

system.

ON

OFF

PROCESS

TEMPERATURE DEW POINT

CONTROL POWER

ON OFF

ALARM

Silenc er

ALARM HORN

A

B

C

D

ACM Series Dehumidifying Dryers Page 15

Safety 2

2-1 Work Rules

Install, operate, and maintain this equipment according to

applicable work and safety codes for your location. This includes

OSHA, CE, NEC, CSA, SPI, and many other local, national, and

international regulations. Obey these specific work rules:

 Read and follow the instructions in this manual before

installing, operating, or maintaining any equipment.

Additional copies are available from AEC, Inc.

 Only qualified persons should work on, or with, this

equipment.

 Work only with approved tools and devices.

 Disconnect and lock out power while working on this

equipment.

2-2 Tools and Equipment Needed

You’ll need the following:

• Hand tools

• Fork lift or overhead lift

• Wire, conduit, and fittings for wiring runs (if receptacle is not

already in place)

• Mounting bolts with nuts and washers

2-3 Mechanical Installation

Dryers may be mounted on the machine, a stand, or a mezzanine.

Be sure it is securely attached and additional bracing is used if

necessary. The sections on the following pages explain general

installation rules.

Read manual thoroughly before installing dryer.

Use approved safety straps or chains to lift the

dryer at the marked lifting points.

Page 16 ACM Series Dehumidifying Dryers

2-4 Safety Considerations

The terms NOTICE, CAUTION, WARNING, and DANGER

have specific meanings in this manual. See Section 13 for a

complete list of specific safety warning information.

A NOTICE is used to indicate a statement of company policy

directly or indirectly related to the safety of personnel or protection

of property.

A CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

A WARNING indicates a potentially hazardous situation which, if

not avoided could result in death or serious injury.

A DANGER indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury. This word will

be limited to the most serious situation(s).

The term IMPORTANT emphasizes areas where equipment

damage could result, or provides additional information to make a

step or procedure easier to understand. Disregarding information

marked IMPORTANT would not be likely to cause personal

injury.

REPORTING A SAFETY DEFECT

NOTE: If you believe that your equipment has a defect which could cause

injury, you should immediately discontinue its use and inform

AEC, Inc., at our address listed in this manual.

The principle factors which can result in injury are:

1. Failure to follow proper operating and clean-out

procedures, i.e. lockout/tagout.

2. Failure to maintain a clean and safe working environment.

ACM Series Dehumidifying Dryers Page 17

2-5 General Responsibility

NO MATTER WHO YOU ARE…

Safety is important. Owners, operators, and maintenance

personnel must realize that every day, safety is a vital aspect of

their jobs.

If your main concern is loss of productivity, remember this:

Production is always affected in a negative way following an

accident. The following are some of the reasons, which can affect

your production:

• Loss of a skilled operator (temporarily or permanently)

• Breakdown of shop morale

• Costly damage to equipment

• Down-time

An effective safety program is responsible and economically

sound.

Organize a safety committee or group, and hold regular meetings.

Promote this group from the management level. Through this

group, the safety program can be continually reviewed,

maintained, and improved. Keep minutes or a record of the

meetings.

Hold daily equipment inspections in addition to regular

maintenance checks. You will keep your equipment safe for

production and exhibit your commitment to safety.

Please read and use this manual as a guide to equipment safety.

This manual contains safety warnings throughout, specific to each

function and point of operation.

2-6 Operator Responsibility

The operator’s responsibility does not end with efficient

production. The operator usually has the most daily contact with

the dryer and intimately knows its capabilities and limitations.

Plant and personnel safety is sometimes forgotten in the desire to

meet incentive rates, or through a casual attitude toward machinery

formed over a period of months or years. Your employer probably

has established a set of safety rules in your workplace. Those

rules, this manual, or any other safety information will not keep

you from being injured while operating your equipment.

Page 18 ACM Series Dehumidifying Dryers

ONLY YOU can make safety work for you by constantly thinking

about what is safe and what is not. It is often the “just once” that

an operator reaches into a dryer to remove material and it results in

serious injury.

Learn and always use safe operation. Cooperate with co-workers

to promote safe practices. Immediately report any potentially

dangerous situation to your supervisor or appropriate person.

REMEMBER:

• NEVER place your hands or any part of your body in any

dangerous location.

• NEVER operate, service, or adjust the dryer without

appropriate training and first reading and understanding this

manual.

• NEVER try to pull material out of the dryer with your hands

while it is running!

• Before you start the dryer check the following:

• Remove all tools from the dryer;

• Be sure no objects (tools, nuts, bolts, clamps, bars) are

laying in the hopper area;

• If your dryer has been inoperative or unattended, check all

settings before starting the unit.

• At the beginning of your shift and after breaks, verify that the

controls and other auxiliary equipment are functioning properly.

• Keep all safety guards in place and in good repair. NEVER

attempt to bypass, modify, or remove safety guards. Such

alteration is not only unsafe, but will void the warranty on your

equipment.

• When changing control settings to perform a different mode of

operation, be sure selector switches are correctly positioned.

Locking selector switches should only be adjusted by authorized

personnel and the keys removed after setting.

• Report the following occurrences IMMEDIATELY:

• unsafe operation or condition

• unusual dryer action

• leakage

• improper maintenance

• NEVER stand or sit where you could slip or stumble

into the dryer while working on it.

• DO NOT wear loose clothing or jewelry, which can be caught

while working on a dryer. In addition, cover or tie back long

hair.

ACM Series Dehumidifying Dryers Page 19

• Clean the dryer and surrounding area DAILY, and inspect the

machine for loose, missing or broken parts.

• Shut off power to the dryer when it is not in use. Turn the

switch to the OFF position, or unplug it from the power source.

2-7 Maintenance Responsibility

Safety is essential to the good health of both operator and machine.

If you are a maintenance worker, you must make safety a priority

in order to effectively repair and maintain equipment.

BEFORE REMOVING, ADJUSTING, OR REPLACING

PARTS ON A MACHINE, REMEMBER TO DO THE

FOLLOWING:

• TURN OFF all air and electric supplies and all accessory

equipment at the machine.

• DISCONNECT AND LOCK OUT electrical and pneumatic

power, and attach warning tags to the disconnect switch and air

shutoff valve.

When you need to perform maintenance or repair work on a dryer

above floor level, use a solid platform or a hydraulic elevator. If

there is a permanently installed catwalk on your dryer, use it. The

work platform should have secure footing and a place for tools and

parts. DO NOT climb on dryers, machines, or work from ladders.

If you need to repair a large component, use appropriate handling

equipment. Before you use handling equipment (portable “A”

frames, electric boom trucks, fork trucks, overhead cranes) be sure

the load does not exceed the capacity of the handling equipment or

cause it to become unstable.

Carefully test the condition of lifting cables, chains, ropes, slings,

and hooks before using them to lift a load.

Be sure that all non-current carrying parts of electrical apparatus,

electrical component enclosures, and the dryer frame are correctly

connected to earth ground with an electrical conductor that

complies with current codes. Install in accordance with national

and local codes, which apply.

When you have completed the repair or maintenance procedure,

check your work, remove your tools, rigging, and handling

equipment.

Page 20 ACM Series Dehumidifying Dryers

Do not restore power to the dryer until all persons are clear of the

area. DO NOT start and run the dryer until you are sure all parts

are functioning correctly.

BEFORE you turn the dryer over to the operator for production,

verify all dryer enclosure panels, guards and safety devices are in

place and functioning properly.

2-8 Safety

2-8-1 Description and Objectives

This section includes information on safety devices and procedures

that are inherent to the ACM Dryer. This manual is not intended to

supersede or alter safety standards established by the user of this

equipment. Instead, the material contained in this section is

recommended to supplement these procedures in order to provide a

safer working environment.

At the completion of this section, the operator and maintenance

personnel will be able to:

• Identify and locate specific safety devices.

• Understand the proper use of the safety devices provided.

• Describe the function of the safety devices.

2-8-2 Safety Circuit Standards

Safety circuits used in industrial systems protect the operator and

maintenance personnel from dangerous energy. They also provide

a means of locking out or isolating the energy for servicing

equipment.

Various agencies have contributed to the establishment of safety

standards that apply to the design and the manufacture of

automated equipment. The Occupational Safety and Health

Administration (OSHA) and the Joint Industrial Council (JIC) are

just a few of the organizations that have joined with the plastics

industry to develop safety standards.

Every effort has been made to incorporate these standards into the

design of the ACM Dryer; however, it is the responsibility of the

personnel operating and maintaining the equipment to familiarize

themselves with the safety procedures and the proper use of any

safety devices.

Page is loading ...

AEC ACM Series Installation guide

AEC ACM Series Installation guide

Other documents