900941-00NC 1
IHP.us.com
REPLACEMENT CLEVIS PIN
AND COTTER PIN KIT
INSTALLATION INSTRUCTIONS FOR INSTALLING REPLACEMENT CLEVIS PIN AND COTTER PIN KIT
[FOR USE WITH MONTECITO ESTATE CAT AND WCT6940WS EPA WOOD-BURNING FIREPLACES]
P/N 900941-00
Rev. NC, 10/2018
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. Clevis Pin
1 ea. Cotter Pin
1 ea. Instruction Sheet
Figure 1 - Remove Bypass Handle and Rubber Sleeve
Figure 2 - Remove Decorative Caps and Retaining Screws
Replacement Clevis Pin and Cotter Pin Kit
Cat. No. Description Where Used
F3714 Clevis Pin and Cotter Pin Kit Montecito Estate CAT and WCT6940WS
Table 1
TOOLS / SUPPLIES NEEDED
Flat head Screwdriver
Needle nose plyers
5/16 wrench
3/8 wrench
GENERAL INFORMATION
The Replacement Clevis Pin And Cotter Pin Kit is available as a replacement
parts kit for the fireplace models listed in Table 1.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact you local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND OPER-
ATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE
INSTRUCTIONS.
TURN OFF THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
Check the contents of the kits upon receipt and check for any damaged
or missing parts. If there is hidden damage, notify your freight company
or IHP dealer immediately.
INSTALLATION INSTRUCTIONS
1. Detach the upper right wooden bypass handle by unscrewing it and re-
move the rubber sleeve on the lower left primary air handle (see Figure 1).
2. Remove the (8) decorative caps on the exterior of the facade. Using a flat
head screwdriver, remove the (8) retaining screws (see Figure 2).
2IHP.us.com
Innovative Hearth Products (IHP) reserves the right to make changes at any
time, without notice, in design, materials, specifications, prices and also
to discontinue colors, styles and products. Consult your local distributor for
fireplace code information.
Printed in U.S.A. © 2018 Innovative Hearth Products
P/N 900941-00 Rev. NC 10/2018 1769 East Lawrence Street • Russellville, AL 35654
Figure 3 - Pull Facade Forward and Remove
Figure 4 - Pull By-Pass Rod Forward to Access Screw and Nut
Figure 5 - Remove Screw and Nut On By-Pass Control Arm
Figure 6 - Insert Clevis Pin
3. Pull the facade forward and remove (see Figure 3).
4. Pull the by-pass rod fully forward to be able to access the screw and nut
(see Figure 4).
5. Using a 3/8” box end and a 5/16” box end ratchet wrench, remove the
screw and nut on the by-pass control arm (see Figure 5).
6. Insert the clevis pin through the By-Pass Lever and By-Pass Lever Sup-
port, push the cotter pin through the hole of the pin, and bend each half
backwards with a set of needle-nose pliers (see Figure 6).
By-Pass Lever Support
Cotter Pin
Clevis Pin
-
1
-
2
Astria Fireplaces WCT6940WS Instruction Sheet
- Type
- Instruction Sheet
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Astria Fireplaces Mega Flame Mossy Oak LMF 24/30/36 MO Instruction Sheet
-
-
-
-
-
-
-
-
Other documents
-
Superior Fireplaces WCT6940 Operating instructions
-
-
-
-
-
-
-
-
Lexmark MONTEST User manual
-