Epson Europe EMP-TW1000 User manual

About the Manuals and Notations Used

Types of Manual

The documentation for your EPSON projector is divided into the following two manuals. Refer to the

manuals in the order given below.

Safety Instructions/World-Wide Warranty Terms

This manual contains information on using the projector safely, and also includes a guide for warranty

service, and a troubleshooting check sheet.

Be sure to read this manual thoroughly before using the projector.

User’s Guide (this manual)

This User's Guide contains information on installing the projector, basic operations, using the

configuration menus, troubleshooting and maintenance.

Notations used in this User’s Guide

General information

Meaning of "unit" and "projector"

When "unit" or "projector" appears in the text of this User’s Guide, they may refer to items which are

accessories or optional equipment in addition to the main projector unit itself.

Indicates procedures where personal injury or damage to the projector may occur if

the procedures are not followed correctly.

Indicates additional information and points which may be useful to know regarding a

topic.

Indicates a page where useful information regarding a topic can be found.

Indicates that an explanation of the underlined word or words in front of this symbol

appears in the glossary of terms.

Refer to the "Glossary" in the "Appendix". p.54

, etc. Indicates buttons on the remote control or projector's control panel.

" (Menu Name) " Indicates configuration menu items.

Example: "Image"-"Color Mode"

[ (Name) ] Indicates the port name of the projector.

Example: [Video]

TIP

1

Checking the Components

When you unpack the projector, make sure that you have all these components.

If any of the components are missing or incorrect, please contact the place of purchase.

❏Projector (with lens cover) ❏Remote control

❏Power cable (3.0m)

Connect to the projector and to a wall outlet.

❏AA alkali batteries (2 pcs.)

Insert into the remote control.

❏Document CD-ROM

(Safety Instructions/World-Wide

Warranty Terms, User’s Guide)

❏Quick Start Guide

* Some regions may have paper manuals instead of a

CD-ROM, or may not have the Quick Start Guide.

❏D SCART adapter

Use a commercially-available SCART cable to

make the connections when projecting RGB-video

and component video images.

* Some regions may not have the D SCART adapter

included as an accessory.

Documentation

2

Table of Contents

■Features of the Projector.............................4

■Part Names and Functions..........................6

Front / Top.................................................... 6

Control panel ................................................ 6

Remote control .............................................7

Rear.............................................................. 8

Base ............................................................. 8

■Appearance................................................... 9

Installing the Projector

■Setting up....................................................10

Adjusting the projection size....................... 10

■Connecting Image Sources....................... 12

■Preparing the Remote Control ..................13

Inserting batteries into the remote control .. 13

Basic Operations

■Projecting Images ...................................... 14

Turning the power on

and projecting images ..............................14

■Adjusting the Projection Screen...............16

Focus adjustment ....................................... 16

Fine adjustments to image size

(Zoom adjustment) ...................................16

Projection image position adjustment

(Lens shift)................................................16

Image Quality Adjustments

■Basic Image Quality Adjustments ............ 18

Selecting the colour mode.......................... 18

Selecting the aspect ................................... 18

■Advanced Colour Adjustments.................20

Skin tone adjustment..................................20

Absolute colour temperature adjustment.... 20

Gamma adjustment ....................................20

RGB adjustment (Offset, Gain) ..................22

Hue and saturation adjustment .................. 22

■Examining Image Quality Further............. 23

Sharpness (Advanced) adjustment ............ 23

Auto Iris (automatic aperture) setting ......... 23

■Viewing Images at a Preset Image Quality

(Memory Function)......................................24

Saving, Loading and Erasing Memory .......24

Configuration Menu

■Configuration Menu Functions ................. 26

Using the configuration menus................... 26

List of configuration menus ........................ 28

"Image" menu............................................. 30

"Signal" menu.............................................31

"Settings" menu..........................................33

"Memory" menu..........................................35

"Reset" menu.............................................. 35

3

Table of Contents

Basic

operation

Appendix Troubleshooting Image Quality

Adjustments

Installing the

projector

Configuration

Menu

Troubleshooting

■Problem Solving ........................................ 36

Reading the indicators ............................... 36

•When the (warning) indicator is lit or

flashing...............................................................36

•When the (operation) indicator is lit or

flashing...............................................................37

When the indicators provide no help.......... 37

•Problems relating to images................................. 38

•Problems when projection starts.......................... 43

•Problems with the remote control........................ 43

Appendix

■Maintenance ............................................... 44

Cleaning..................................................... 44

•Cleaning the air filter............................................44

•Cleaning the projector case ..................................44

•Cleaning the lens ..................................................44

Consumable replacement periods ............. 45

•Air filter replacement period ................................45

•Lamp replacement period .....................................45

Replacing consumables............................. 46

•Replacing the air filter..........................................46

•Replacing the lamp...............................................46

•Resetting the lamp operating time........................46

■Optional Accessories / Consumables ..... 48

■List of Supported Monitor Displays ......... 49

•Component Video................................................ 49

•Composite Video/S-Video................................... 49

•Computer image (analog RGB) ........................... 50

•Input signal from the [HDMI] input port............. 50

■Specifications ............................................ 51

■Glossary ..................................................... 54

■Index ........................................................... 56

4

Features of the Projector

Image appearance can be selected to match the

projection environment (Color Mode)

Sophisticated colour adjustment

The optimum images for the location can be projected simply by selecting the desired colour mode from the

following six preset modes.

If "Natural", "Theatre", "Theatre Black 1" or "Theatre Black 2" is selected, the Epson Cinema Filter effect is

applied automatically to increase the contrast and to make skin tones appear with more natural tints. p.18

In addition to the "Color Mode", the absolute colour temperature and skin tones can be adjusted by simple

procedures to render the picture even more to your own liking. Further, you can adjust gamma, the offset and

gain for RGB colours, and the hue and saturation of RGBCMY colours, to create colours that match the image.

p.20

Color

Mode

Theatre Black1

Theatre Black2

Dynamic

Living Room

Natural

Theatre

5

Features of the Projector

Equipped with a wide-

angle lens shift function

The lens shift function allows the position of the

projected images to be adjusted vertically and

horizontally without distorting the images.

This can allow the projector to be set up with greater

freedom, even if it is suspended from a ceiling or at

an angle to the screen. p.16

For zoom adjustment, 2.1x short throw zoom lens is provided.

Images can be projected onto an 100" screen (16:9 screen

only) even at a distance of approximately 3 m (10 ft.). p.10

Advanced image quality adjustment functions such as "Auto Iris" and "Sharpness (Advanced)" can be used to

enjoy even sharper images. With the Auto Iris function turned on, the amount of light can be automatically

adjusted to match the images being projected, to create images with depth and perspective. The Sharpness function

is used to adjust not only the entire image, but also to emphasize specific regions, such as hair and clothing.

p.23

A variety of image setting functions

Advanced image quality adjustment functions

Some of the other many functions that are available are as follows.

EPSON Super White is used to prevent overexposure that can result in images that are too bright. p.32

A progressive conversion that lets you obtain ideal results both for images with large amounts of movement

and for still images. p.32

An aspect function that allows images to be viewed in wide-screen format. p.18

Memory functions that allow adjustment results to be stored and later retrieved easily using the remote control.

p.24

Lock settings that can be used to lock the projector's control panel after adjustments have been made so that

they cannot be changed by mistake, or to prevent children from accidentally turning on the power and looking

into the lens.

p

.33

Equipped with 2.1x short

throw zoom lens

6

Part Names and Functions

Front / Top

Control panel

Buttons with no explanation function in the same way as the corresponding buttons on the remote

control. Refer to "Remote control" for further details on these buttons.

•Front adjustable feet p.17

Extend to adjust the projection angle so that the

projector is horizontal when placed on a desk top.

•Control panel See below

•Air exhaust vent

•Remote control light-

receiving area

p.13

Receives signals from the

remote control.

•Vertical lens adjustment

dial p.16

Moves the lens vertically.

•Lens cover

Attach when not using

the projector to prevent

the lens from becoming

dirty or damaged.

•

H

or

i

zonta

l

ens a

dj

ustment

di

a

l

p.

16

Moves the lens horizontally.

Do not touch the exhaust vent

immediately after projecting, or

while projecting, since it

becomes hot.

•Focus ring p.16

Adjusts the image focus.

•Zoom ring p.16

Adjusts the image size.

• (Operation) indicator p.37

Flashes or lights in different colours to indicate the operating

status of the projector.

• (Warning) indicator p.36

Flashes or lights in different colours to indicate problems

with the projector.

•Power button p.14

Turns the projector power

on or off.

• buttons

p.18, 20, 22, 26

•Select/Line menu buttons

p.18, 24, 26

•Menu button p.26

•Source button p.15

Selects the image source.

•Esc button

p.18, 20

,

24

,

26

•Aspect button p.18

7

Part Names and Functions

Remote control

•Remote control light-

emitting area p.13

Outputs remote control signals. •On/Off buttons p.14

Turns the projector power on/off.

•

Indicator

Illuminates when remote control

signals are being output.

•Memory button p.24

Retrieves stored memories.

•Menu button

p.26

Displays the full-screen

configuration menus.

•Select/Line menu button

p.18, 24

,

26

Displays the line menu.

When viewing a menu, press this

button to select the menu item and

proceed to the next display.

• button

p.18, 20, 22, 26

Press to select menu items and

adjustment values.

•Gamma button p.20

Adjusts the gamma values.

•Color Temp. button p.20

Adjusts the absolute colour

temperature.

•Contrast button p.30

Adjusts contrast .

•S.Tone (Skin Tone)

button p.20

Adjusts the skin tones of people

who appear in the images.

•Blank button

The projected images switch off

and on each time this button is

pressed.

• (Illumination) button

All buttons on the remote control illuminate when this button is pressed.

The button illumination switches off automatically after about 10 seconds

have passed.

•Color Mode button p.18

Selects the colour mode.

•Aspect

button p.18

Selects the aspect.

•Esc button

p.18

,

20

,

24

,

26

Pressing [Esc] while viewing a

menu displays the previous menu.

Switches to an image input from

equipment connected to the port.

•HDMI button

•D/SCART button

•Compo. button

•PC button

•S-Video button

•Video button

Source buttons p.15

•Pattern button p.17

The test pattern image appears and

disappears each time this button is

pressed.

8

Part Names and Functions

Rear

Base

•[SCART] input port p.12

Connects to the component

(YCbCr or YPbPr) out port or D

out port of the video equipment.

•[Trigger out] port

When the projector power

is turned on, a 12 V DC

signal is output from this port.

When the projector's power is

turned off or a problem with

operation occurs, the output

becomes 0 V to send the

projector's power ON/OFF

status to an external device.

•[Video] input port p.12

Connects to general video out

ports of the video equipment.

•[HDMI ] input port p.12

Connects to video equipment or a

computer that is HDMI-

compatible.

•[S-Video] input port p.12

Connects to the S-Video out ports of

the video equipment.

•[RS-232C] port

Connects the projector to a computer

using an RS-232C cable. This port is

for control use and should not be used

by the customer.

•Power inlet p.14

Connects the power cable.

•Main power switch

p.14

•Security lock

p.55

•Remote control

light-receiving

area p.13

Receives signals

from the remote

control.

•[PC] input port p.12

Connects to the RGB out

port of the computer.

•[Component] input port p.12

Connects to the component (YCbCr or YPbPr ) out port of the

video equipment.

•Suspension bracket fixing points (4 points) p.48

Install the optional ceiling mount here when suspending the projector from a ceiling.

•Air filter (air intake vent)

p.44, 46

Prevents dust and other foreign particles

from being drawn into the projector.

It should be cleaned periodically.

•Lamp cover p.46

Open this cover when replacing the lamp

inside.

9

Appearance

406

Centre of projector Centre of lens

*1 Distance from centre of lens to suspension bracket fixing point

(Lens shift amount: Max. 8.8 mm vertically)

*2 Distance from centre of lens to centre of projector

(Lens shift amount: Max. 7.7 mm horizontally)

110*2

131.5

66*1

19

124

310

77.3

4-M4×8

Units:mm

52.8

Centre of lens

160

300

143

10

Setting up

Adjusting the projection size

17 to -17 (6.8 to -6.8)

23 to -23 (9.1 to -9.1 )

35 to -35 (13.6 to -13.6)

58 to -58 (22.7 to -22.7)

69 to -69 (27.2 to -27.2)

46 to -46 (18.2 to -18.2)

86 to -86 (34.0 to -34.0)

Centre of lens

Lens shift

To p

Lens shift

Bottom

Offset

Projection distance

Adjusting the projection size

Lens shift adjustment

The size of the projected image is basically determined by the distance from the projector's lens

to the screen.

Hanging from the ceiling

A screen in a high location

Projector situated to the side so that the screen can be viewed sitting right in front of it

Projector situated on a shelf, etc.

When positioning an image using the lens shift dial, hardly any deterioration of the image occurs because the lens

shift correction is adjusted optically. However, for optimal image quality the lens shift function should not be used.

The lens shift dials can be used to position the image and is especially useful when using the projector in the

following locations. p.16

While referring to the table below, position the projector so that the images are projected onto the

screen at the optimum size.

The values should be used as a guide for setting up the projector.

The height from the centre of the lens to the bottom of the

screen will vary depending on the lens shift setting.

Units: cm (in.)

4:3 screen size

Units: cm (in.)Units: cm (ft.)

Units: cm (in.)

16:9 screen size Longest

(Tele)

Shortest

(Wide) to

Projection distance

120×90 (47×35)

160×120 (63×47)

200×150 (79×59)

61×46 (24×18)

81×61 (32×24)

240×180 (94×71)

60"

100"

80"

30"

40"

120"

150" 300×230 (118×91)

130×75 (51×28)

180×100 (71×39)

220×120 (87×47)

177 to 380 (5.8 to 12.5)

298 to 636 (9.8 to 20.9)

66×37 (26×15)

89×50 (35×20)

87 to 188 (2.8 to 6.2)

117 to 252 (3.8 to 8.3)

238 to 508 (7.8 to 16.7)

270×150 (106×59)

60"

100"

80"

30"

40"

120"

150" 330×190 (130×75)

359 to 764 (11.8 to 25.1)

450 to 956 (14.7 to 31.4)

Offset to Offset

21 to -21 (8.3 to -8.3)

28 to -28 (11.1 to -11.1 )

42 to -42 (16.7 to -16.7)

71 to -71 (27.8 to -27.8)

85 to -85 (33.3 to -33.3)

56 to -56 (22.2 to -22.2)

106 to -106 (41.7 to -41.7)

217 to 465 (7.1 to 15.3)

365 to 778 (12.0 to 25.5)

106 to 230 (3.5 to 7.6)

143 to 309 (4.7 to 10.1)

291 to 622 (9.6 to 20.4)

439 to 935 (14.4 to 30.7)

550 to 1170 (18.0 to 38.4)

Longest

(Tele)

Shortest

(Wide) to

Offset to Offset

11

Setting up

Installing the Projector

* When suspending the projector from a ceiling,

change the configuration menu settings. p.34

Projection methods

When projecting from directly in front

When projecting from a celling

When projecting from the side of

the screen

* Even if projection will be from the screen

side, set up the screen and projector so that

they are parallel.

Configuration menu

Settings Projection

Front

Front/Ceiling

Avoid setting the projector up in a place which is very dusty or humid, or where there

will be cigarette or other smoke, especially oily smoke.

Clean the air filter at least once every 3 months.

Clean the air filter more frequently if using the projector in a dusty environment.

A special method of installation is required when suspending the projector from the

ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident

and injury.

If you use adhesives on the ceiling mount to prevent the screws from loosening, or if

you use things such as lubricants or oils on the projector, the projector case may

crack causing it to fall from its ceiling mount. This could cause serious injury to

anyone under the ceiling mount and could damage the projector.

When installing or adjusting the ceiling mount, do not use adhesives to prevent the

screws from loosening and do not use oils or lubricants and so on.

Do not use the projector on its side. This may cause malfunctions to occur.

12

Connecting Image Sources

*1 If a DVD has been connected using a D SCART adapter, change the "D/SCART" setting in the "Input Signal" to

"SCART". p.34

*2 Some regions may not have the D SCART adapter included as an accessory.

•Turn the power off for both the projector and the signal source before connecting them.

If the power for either device is on at the time of connection, damage may result.

•Check the shapes of the cable connectors and the device ports before making the

connections. If you try to force a connector to fit a device port with a different shape or

number of terminals, a malfunction or damage to the connector or port may result.

•Some signal sources may have specially-shaped ports. In such cases, use the

accessory or optional cables that are supplied with the signal source to make the

connections.

•The cable that should be used to connect video equipment to the projector will depend

on the type of video signal that the equipment outputs. Some kinds of video equipment

output several different types of video signal. The image quality ranking of the video

signal types is generally held to be as follows, in descending order of quality:

Digital component video [HDMI ] > Analog component video [D] [Component] >

S-Video [S-Video] > Composite video [Video]

You should refer to the documentation provided with the video equipment being used to

check what types of video signal formats the equipment can output. The composite

video format is sometimes simply called "video output".

HDMI

SCART cable

(commercially-

available)

+

D SCART

adapter*

2

(accessory)

Video equipment (VHS VCR, DVD player, game console, etc.)

*Port names may vary depending on the equipment being connected.

Computer

S-Video

S-Video cable

(commercially-

available)

Video

RCA video cable

(commercially-

available)

SCART

*1

Component

video cable

(commercially-

available)

HDMI cable

(commercially-

available)

Component output Mini D-Sub

15-pin

Mini D-Sub

15-pin

Computer cable

(commercially-

available)

TIP

13

Installing the Projector

Preparing the Remote Control

Inserting batteries into the remote control

The remote control is not supplied with batteries already inserted. Insert the accessory batteries

before using the remote control.

If delays in the responsiveness of the remote control occur or if it does not operate

after it has been used for some time, it probably means that the batteries are

becoming flat. If this happens, replace the batteries with two new batteries. Use two

new AA batteries as replacement batteries.

Remove the battery cover.

Insert the batteries.

Install the battery cover.

While pressing the knob, lift up. Insert the tab.

Press down until the battery

cover clicks into place.

Check the (+) and (-)

indications inside the

battery compartment and

insert the batteries so that

they face correctly.

TIP

Using the remote control

Operating range (horizontal)

Operating range (vertical)

Remote control light-receiving area

Operating distance

Approx.10m

Remote control

light-emitting area

Operating distance

Approx.10m

Operating distance

Approx.10m

Approx.30 Approx.30 Approx.30 Approx.30

Approx.30

14

Projecting Images

Turning the power on and projecting images

TIP

If you set the "Direct Power On" to "On", the power of the unit will turn ON when

the main power switch is turned ON, without having to press the power button of

the remote control or the projector's control panel.

If there is a problem with projection even though the projector is set up and connected correctly,

refer to p.15, 36.

The projector is equipped with a "Child Lock" function that prevents young

children from accidentally turning the power on and looking into the lens, and

also an "Operation Lock" function that prevents mis-operations. p.33

When using above an altitude of about 1500 m, make sure you set the "High

Altitude Mode" to "On". p.33

This projector is equipped with an automatic

adjustment function that automatically optimizes it

when a computer input signal is switched.

If a laptop computer or a computer with a LCD

screen has been connected to the projector, you

may need to use keyboard or function settings to

change the output destination. While holding down

the key, press (the key with a symbol such

as / on it). After the selection is made,

projection will soon start.

Computer documentation

NEC

Panasonic

SOTEC

HP

Toshiba

IBM

SONY

DELL

Fujitsu

Macintosh

Example of output selection

Set mirror setting or

display detection.

Depending on OS, you can

change the output

selection by pressing .

ON

Remove the lens cover.

Connect the power

cable.

Turn on the main power

switch.

Turn the power on for the

connected equipment.

Turn the power on.

Control Panel Remote Control

15

Projecting Images

Basic Operations

When the expected images are not

projected

Turning the power off

Simply pressing or does not stop

electricity consumption.

When the expected images are not projected

If more than one signal source has been connected, or if no images are projected, use the remote control or the

projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video

equipment first, then select the signal source.

Using the remote control

Press the button that has the name of the port on it that

the desired signal source is connected to.

Using the control panel

When you press , the menu is displayed.

Each press of moves the pointer. Move the pointer

to the target input source to select it.

Press to accept. The input source is automatically

changed if no operations are performed for about 5

seconds with the pointer at the target input source.

Turning the power off

Turn the power off for the signal sources

that are connected to the projector.

Press on the remote control or on

the projector's control panel. If you press

on the projector's control panel, the

following message will be displayed.

Press again to continue.

When the projector has cooled down (takes

about 30 seconds), turn off the main power

switch.

Attach the lens cover.

TIP

When the colour of the image projected from the [D] or [Component] input port

is unnatural, select an appropriate signal according to the signal from the device

connected at "Input Signal" in the Configuration menu. p.34

16

Adjusting the Projection Screen

Focus adjustment

Fine adjustments to image size (Zoom

adjustment)

Projection image position adjustment

(Lens shift)

The lens shift function can be used to move

the image display position vertically and

horizontally within the range shown in the

figure on the right when you cannot set up

this projector directly in front of the screen,

or when the image is projected too low or

too high.

When you turn the lens shift dial and hear a

click, the lens position is almost centred.

The image display position cannot be

moved to the maximum positions in both

the vertical and horizontal positions.

Projection image position adjustment (Lens shift)

Standard projection position

(centre position for lens shift)

Range that the picture can be shifted

from the standard projection position

V

1/2H

H

1/2V

Turn the focus ring to adjust the focus.

Focus adjustment

Fine adjustments to image size (Zoom adjustment)

Turn the zoom ring to adjust the size of the projected image.

Ex) The image cannot be shifted

vertically when it has been shifted

horizontally by the full amount.

When the image has been shifted

vertically by the full amount, it can

be shifted up to 9% of the horizontal

width of the screen.

Move

upwards

Move

downwards Move to

the left

Move to

the right

Wide

Te l e

When transporting the

projector, make sure to turn the

lens position down by the full

amount. Otherwise the lens

shift mechanism may be

damaged.

17

Adjusting the Projection Screen

Basic Operations

Correcting projector tilt

Displaying a test pattern

Extend ExtendRetract Retract

Correcting projector tilt

If the projected images are tilted horizontally ( ), use the front adjustable feet to adjust the projector

so that it is horizontal.

You can project a test pattern at times such as when setting up the projector in order to perform

adjustments in the line menu, and zoom and focus adjustments without having to connect video equipment.

If on the remote control is pressed, the test pattern appears.

Displaying a test pattern

1/2H

1/2V

To stop displaying the test pattern, press again.

18

Basic Image Quality Adjustments

Selecting the colour mode

Selecting the aspect

Press or on the remote control

or on on the projector's control

panel to select an item.

Press or to confirm the

selection.

*If you press , the Select menu

disappears.

If you project an image that is

compressed, enlarged or separated

using the aspect function in public

places such as a store or hotel for

the purposes of profit-making or

public display, it may result in

infringing on the author's right that

is protected by copyright law.

TIP

Selecting the colour mode

Press and select the colour mode from

the menu.

Setting is also possible using the configuration

menu.

Selecting the aspect

Press and select the aspect mode from the

menu.

When projecting using Auto

*1 Not usable during computer input. Not

compatible with certain component video

signals.

*2 If Auto is not suitable, the setting will become

Normal.

For 4:3 input signals

For input images recorded

in squeeze mode

For letterbox input signals

Normal

Full

Zoom

Select Menu Operations

Page is loading ...

Epson Europe EMP-TW1000 User manual

This manual is also suitable for

Epson Europe EMP-TW1000 User manual

Related papers

Other documents