Tektronix TDS1000- and TDS2000- User manual

Category
Measuring, testing & control
Type
User manual

This manual is also suitable for

User Manual
TDS1000- and TDS2000-Series
Digital Storage Oscilloscope
071-1064-00
This document supports firmware version
FV:v1.00 and above.
www.tektronix.com
Copyright © Tektronix, Inc. All rights reserved.
Tektronix products are covere d by U.S. and foreign patents, issued and
pending. Information in this publication supercedes that in all previously
published materia l. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered trade marks of Tektronix, Inc.
WARRANTY SUMMARY
(TDS1000- and TDS2000-Series Digital St orage Oscilloscope)
Tektronix warrants that the products that it manufactures and sells will be free from defects
in materials and workmanship for a period of three (3) years from the date of shipment
from an authorized Tektronix distributor. If a product or CRT proves defective within the
respective period, T ektronix will provide repair or replacement as described in the complete
warranty statement.
To arrange for service or obtain a copy of the complete warranty statement, please contact
your nearest Tektronix sales and service office.
EXCEPT AS PROVIDED IN THIS SUMMARY OR THE APPLICABLE WARRANTY
STATEMENT, TEKTRONIX MAKES NO WARRANTY OF ANY KIND, EXPRESS
OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL TEKTRONIX BE LIABLE FOR INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES.
WARRANTY SUMMARY
(P2200 Probe)
Tektronix warrants that the products that it manufactures and sells will be free from defects
in materials and workmanship for a period of one (1) year from the date of shipment. If a
product proves defective within the respective period, Tektronix will provide repair or
replacement as described in the complete warranty statement.
To arrange for service or obtain a copy of the complete warranty statement, please contact
your nearest Tektronix sales and service office.
EXCEPT AS PROVIDED IN THIS SUMMARY OR THE APPLICABLE WARRANTY
STATEMENT, TEKTRONIX MAKES NO WARRANTY OF ANY KIND, EXPRESS
OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL TEKTRONIX BE LIABLE FOR INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES.
TDS1000/2000-Series Digital Oscilloscope User Manual
i
Table of Contents
General Safety Summary v............................
Preface vii............................................
Help System ix........................................
Conventions xi........................................
Product End-of-Life Handling xii..........................
Contacting Tektronix xiii.................................
Getting Started 1.....................................
General Features 2....................................
Installation 4.........................................
Power Cord 4......................................
Security Loop 4....................................
Functional Check 5....................................
Probe Safety 6........................................
Probe Check Wizard 7.................................
Manual Probe Compensation 8...........................
Probe Attenuation Setting 9.............................
Self Calibration 10.....................................
Understanding Oscilloscope Functions 11.................
Setting Up the Oscilloscope 12...........................
Using Autoset 12....................................
Saving a Setup 12...................................
Recalling a Setup 12.................................
Default Setup 13....................................
Triggering 13.........................................
Source 14..........................................
Types 15..........................................
Modes 15..........................................
Coupling 15........................................
Position 16.........................................
Slope and Level 16..................................
Table of Contents
ii
TDS1000/2000-Series Digital Oscilloscope User Manual
Acquiring Signals 17...................................
Acquisition Modes 17................................
Time Base 18......................................
Scaling and Positioni ng Waveforms 18.....................
Vertical Scale and Position 18.........................
Horizontal Scale and Position; Pretrigger Informat ion 19....
Taking Measurements 24................................
Graticule 24........................................
Cursors 25.........................................
Automatic 25.......................................
Operating Basics 27...................................
Display Area 28.......................................
Message Area 31....................................
Using the Menu System 32...............................
Vertical Controls 34....................................
Horizontal Controls 35..................................
Trigger Controls 36.....................................
Menu and Control Buttons 38............................
Connectors 39.........................................
Application Examples 41...............................
Taking Simple Measurements 42..........................
Using Autoset 42....................................
Taking Automatic Measurements 43....................
Measuring Two Signals 46............................
Taking Cursor Measurements 48..........................
Measuring Ring Frequency 48.........................
Measuring Ring Amplitude 49.........................
Measuring Pulse Width 50............................
Measuring Rise Time 51..............................
Analyzing Signal Detai l 54..............................
Looking at a Noisy Signal 54..........................
Separating the Signal from Noise 55....................
Capturing a Single-Shot Signal 56.........................
Optimizing the Acquisition 57.........................
Measuring Propagation Delay 58..........................
Table of Contents
TDS1000/2000-Series Digital Oscilloscope User Manual
iii
Triggering on a Specific Pulse Width 60....................
Triggering on a Video Signal 62...........................
Triggering on Video Fields 63.........................
Triggering on Video Lines 64..........................
Using the Window Function to See Waveform Details 66....
Analyzing a Differential Communication Signal 68...........
Viewing Impedance Changes in a Network 70...............
Reference 73.........................................
Acquire 74............................................
Autoset 79............................................
Sine Wave 81......................................
Square Wave or Pulse 82.............................
Video Signal 83.....................................
Cursors 84............................................
Default Setup 85.......................................
Display 86............................................
Help 89..............................................
Horizontal 90.........................................
Math 93..............................................
Measure 94...........................................
Print 96..............................................
Probe Check 96........................................
Save/Recall 97........................................
Trigger Controls 99.....................................
Utility 110.............................................
Vertical 112............................................
Math FFT 115.........................................
Setting Up the Time-Domain Waveform 116.................
Displaying the FFT Spectrum 118..........................
Selecting an FFT Window 120.............................
Magnifying and Positioning an FFT Spectrum 124.............
Measuring an FFT Spectrum Using Cursors 126...............
Table of Contents
iv
TDS1000/2000-Series Digital Oscilloscope User Manual
TDS2CMA Communications Module 127..................
Installing and Removing an Extension Module 127............
Checking Module Installation 130..........................
Troubleshooting Module Insta llation 130....................
Sending Screen Data t o an External Device 131...............
Setting Up and Testing the RS-232 Interface 134..............
Transferring Binary Data 141...........................
Reporting RS-232 I/O Errors 141........................
Setting Up and Testing the GPIB Interface 143................
Command Entry 150.....................................
Appendix A: Specifications 151...........................
Appendix B: Accessories 169.............................
Appendix C: General Care and Cleaning 173...............
Appendix D: Default Setup 175...........................
Appendix E: GPIB and RS-232 Interfaces 179..............
Index 181.............................................
TDS1000/2000-Series Digital Oscilloscope User Manual
v
General Safety Summary
Review the following safety precautions to avoid injury and prevent
damage to this product or any products connected to it. To avoid
potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or Personal Injury
Use Proper Power Cord. Use only the power cord specified for this
product and certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes
or test leads while they are connected to a voltage source.
Ground the Product. T his product is grounded through the grounding
conductor of the power cord. To avoid electric shock, the grounding
conductor must be connected to earth ground. Before making
connections to the input or output terminals of the product, ensure
that the product i s properly grounded.
Connect the Probe Properly. The probe ground le ad is at ground
potential. Do not connect the ground lead to an elevated voltage.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all
ratings and marki ng on the product. Consult the product manual for
further ratings information before m aking connections to the product.
Do Not Operate Without C overs. Do not operate this product with
covers or panels removed.
Use Proper Fuse. Use only the fuse type and rating specified for this
product.
Avoid Exposed Circuitry. Do not touch exposed connections and
components when power is present.
Do Not Operate With Suspected Failures. If you suspect there is damage
to this product, have i t inspected by qualified service personnel.
Provide Proper Ventilation. Refer to the manual’s installation
instructions for details on installing the product so it has proper
ventilation.
General Safety Summary
vi
TDS1000/2000-Series Digital Oscilloscope User Manual
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Safety Terms and Symbols
Terms in This Manual. These terms may appear in this manual:
WARNING. Warning statements identify condit ions or practices that
could result in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that
could result i n damage to this product or other property.
Terms on the Product. The se terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you
read the marking.
WARNING indicates an injury hazard not immediately accessible as
you read the marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The se symbols may appear on the product:
Protective Ground
(Earth) Terminal
CAUTION
Refer to Manual
Measurment
Ground Terminal
Measurment
Input Terminal
Mains Disconnected
OFF (Power)
Mains Connected
ON (Power)
TDS1000/2000-Series Digital Oscilloscope User Manual
vii
Preface
This manual contains operati n g information for the TDS1000-Series
and TDS2000-Series Digital Storage Oscilloscopes. The manual
consists of the following chapters:
H The Getting Started chapter briefly describes features of the
oscilloscope and provides installation instructions.
H The Understanding Oscilloscope Functions chapter describes
basic operations and functions of the oscilloscope: setting up the
oscilloscope, triggering, acquiring data, scaling and positioning
waveforms, and taking measurem ents.
H The Operating Basics chapter covers operating principles of the
oscilloscope.
H The Application Examples chapter includes examples of a wide
variety of measurem ents to give you ideas on how to solve your
own measurement problems.
H The Reference chapter describes the selections or available range
of values for ea ch option.
Preface
viii
TDS1000/2000-Series Digital Oscilloscope User Manual
H The Math FFT chapter contains detailed informa tion about how
to use the Mat h FFT function.
H The TDS2CMA Communications Module chapter describes this
optional module and how to set up the RS-232, GPIB, and
Centronics ports to use the oscilloscope with external devices,
such as printers and computers.
H The Appendix A: Specifications chapter includes electrical,
environmental, and physical specifications for the osc illoscope,
as well as certifications and compliances.
H The Appendix B: Accessories chapter briefly describes standard
and optional accessories.
H The Appendix C: General Care and Cle aning chapter describes
how to take care of the oscilloscope.
H The Appendix D: Default Setup chapt er contains a list of the
menus and controls with the default (factory) settings that are
recalled when you push the DEFAULT SETUP front-panel
button.
H The Appendix E: GPIB and R S-232 Interfaces chapter compares
the two protocols to help you decide which one to use.
Preface
TDS1000/2000-Series Digital Oscilloscope User Manual
ix
Help System
The oscilloscope has a Help system with topics that cover all the
features of the oscilloscope. You can use the Help system to display
several kinds of information:
H General information about understanding and using the
oscilloscope, such as Using the Menu System.
H Information about specific menus and controls, such a s the
Vertical Position Control.
H Advice about problems you may fac e whil e using an oscillo-
scope, such as Reducing Noise.
The Help system provides three ways for you to find the information
you need: context-sensitive, hyperlinks, and an index.
Context-Sensitive
The oscilloscope displays information about the last menu displayed
on the screen when you push the HEL P front-panel button. The
HELP SCROLL LED lights under the HORIZONTAL POSITION
knob to indicate the a lternative function of the knob. If the topic uses
more than one page, turn the HEL P SCROLL knob to move from
page to page within t he t opic.
Preface
x
TDS1000/2000-Series Digital Oscilloscope User Manual
Hyperlinks
Most of the help topics contain phrases marked with angle bra ckets,
such as <Autoset>. These are links to other topics. Turn the HELP
SCROLL knob to move the hi ghlight from one link to another. Push
the Show Topic option button to display the topic corresponding to
the highlighted link. Push the Back opti on button to return to the
previous topic.
Index
Push the front--panel HELP button, then push the Index option
button. Push the Page Up or Page Down option buttons until you find
the index page that contains the topic you want to view. Turn the
HELP SCROLL knob to highlight a help topic. Push the Show Topic
option button to display the topic.
NOTE. Push the Exit opt ion button or any menu button to remove the
Help text from the screen and return to displaying waveforms.
Preface
TDS1000/2000-Series Digital Oscilloscope User Manual
xi
Conventions
This manual uses the following conve ntions:
H Front-panel buttons, knobs and connectors appear in all
uppercase letters. For example: HEL P, PRINT.
H Menu options appear with the first letter of each word in upper
case. For example: Peak Detect, Window Zone.
Front-panel buttons and
knob labels — All upper case
Option buttons — First letter of
each word on screen is upper case
NOTE. Option buttons can also be called screen buttons, side-menu
buttons, bezel buttons, or soft keys.
H The
" delimiter separates a series of button pushes. For example,
UTILITY
" Options " RS-232 means that you push the
UTILITY button, then push the Options option button, and then
push the RS-232 option butt on.
Preface
xii
TDS1000/2000-Series Digital Oscilloscope User Manual
Product End-of -Life Handling
Components that Contain Mercury. The cold cathode fluorescent tube
located in the liquid crystal display backlight contains trace a mounts
of mercury. When you are ready to reclaim the instrument, you must
properly transfer it according to local regulations concerning
mercury-containing equi pment or ship the instrument to the
Tektronix Recycling Opera tions (RAMS). You can c ontact Tektronix
for the RAMS shipping address and instructions.
Preface
TDS1000/2000-Series Digital Oscilloscope User Manual
xiii
Contacting Tektronix
Phone 1-800-833-9200*
Address Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
Web site www.tektroni x.com
Sales
support
1-800-833-9200, select option 1*
Service
support
1-800-833-9200, select option 2*
Technical
support
Email: techsupport@tektroni x.com
1-800-833-9200, select option 3*
6:00 a.m. -- 5:00 p.m. Pacific time
* This phone number is toll free in North America. After office
hours, please leave a voice mail message.
Outside North America, contact a Tektronix sales office or
distributor; see the Tektronix web site for a list of offices.
Preface
xiv
TDS1000/2000-Series Digital Oscilloscope User Manual
TDS1000/2000-Series Digital Oscilloscope User Manual
1
Getting Started
TDS1000-Series and TDS2000-Series Digital Storage Oscilloscopes
are small, lightweight, benchtop packages that you can use to take
ground-referenced measurements.
In addition to the list of general features, this chapter describes how
to do the following tasks:
H Install your product
H Perform a brief functional chec k
H Perform a probe check and compensate probes
H Match your probe a ttenuation factor
H Use the self calibration routine
NOTE. You can select a language to display on the screen when you
power on the oscilloscope. At any time, you can push the UTILITY
button, and push the Language option button to select a language.
Getting Started
2
TDS1000/2000-Series Digital Oscilloscope User Manual
General Features
The next table and bulleted list describe the general features.
Model Channels Bandwidth Sample rate Display
TDS1002 2 60 MHz 1.0 GS/s Monochrome
TDS1012 2 100 MHz 1.0 GS/s Monochrome
TDS2002 2 60 MHz 1.0 GS/s Color
TDS2012 2 100 MHz 1.0 GS/s Color
TDS2014 4 100 MHz 1.0 GS/s Color
TDS2022 2 200 MHz 2.0 GS/s Color
TDS2024 4 200 MHz 2.0 GS/s Color
H Context-sensitive Help system
H Color or monochrome L CD display
H Selectable 20 MHz bandwidth limit
H 2500 point record length for each channel
H Autoset Menu
H Probe Check Wizard
H Cursors with readouts
H Trigger frequency readout
H Eleven automatic measurements
H Waveform averaging and peak detect ion
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206

Tektronix TDS1000- and TDS2000- User manual

Category
Measuring, testing & control
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI