Flymo Contour Cordless 24V Owner's manual

®

Contour Cordless

24 V

GB PL

DE CZ

FR SK

NL SI

NO HR

FI

LT

SE

RU

DK

EE

ES

LV

PT

RO

IT GR

HU TR

Original Instructions

Tłumaczenie oryginalnej instrukcji

obsługi

Übersetzung der

Originalbetriebsanleitung

Překlad originálního návodu na provoz

Traduction du mode d’emploi original Preklad originálneho návodu na obsluhu

Oversat fra den originale

driftsvejledning

Prevod izvirnih navodil za uporabo

Oversettelse av original-

driftsveiledningen

Prijevod originalnih uputa za uporabu

Alkuperäisen käyttöohjeen käännös

Eksploatavimo instrukcijos originalo

vertimas

Översättning av original-

bruksanvisningen

Перевод оригинальной инструкции

по эксплуатации

Oversat fra den originale

driftsvejledning

Kasutamisjuhendi algupärandi tõlge

Traducción de las instrucciones

de empleo originales

Oriģinālās lietošanas instrukcijas

tulkojums

Tradução do manual de instruções

original

Traducerea instrucţiunilor de utilizare

originale

Traduzione delle istruzioni per l’uso

originali

Μετάφραση των πρωτότυπων οδηγιών

λειτουργίας

Az eredeti használati utasítás fordítása Orijinal işletim kılavuzu çevirisi

5012693-01 Contour Cordless 24V Euro.indb 1 16.10.15 11:27

2

GB PL

DE CZ

FR SK

NL SI

NO HR

FI

LT

SE

RU

DK

EE

ES

LV

PT

RO

IT GR

HU TR

IMPORTANT INFORMATION

Read before use and retain for future

reference

UWAGA

Zapoznać się z treścią niniejszej instrukcji

przed użyciem i zachować ją do dalszego

użytkowania urządzenia

WICHTIGE INFORMATION

Bitte vor dem Benutzen des Gerätes

durchlesen und gut aufbewahren.

DŮLEŽITÁ INFORMACE

Než začnete stroj používat, přečtěte si

pozorně tento návod a uschovejte jej pro

další použití v budoucnu.

RENSEIGNEMENTS IMPORTANTS

A lire avant usage et à conserver pour

référence ultérieure.

DÔLEŽITÉ INFORMÁCIE

Pred použitím si prečítajte nasledovné

informácie a odložte si ich pre budúcu

potrebu.

BELANGRIJKE INFORMATIE

Leest u deze informatie voor het gebruik en

bewaar ze voor toekomstige raadpleging.

POMEMBNA INFORMACIJA

Preberite pred uporabo in shranite za

prihodnjo uporabo.

VIKTIG INFORMASJON

Les bruksanvisningen nøye før bruk og

oppbevar den for senere bruk.

VAŽNE INFORMACIJE

Pročitati prije upotrebe i sačuvati za buduće

osvrte.

TÄRKEÄÄ TIETOA

Lue tämä ennen käyttöä ja säilytä

myöhempää tarvetta varten

OPERATORIAUS INSTRUKCIJŲ

RINKINYS

Perskaitykite šį instrukcijų rinkinį labai

atidžiai, kad pilnai suprastumėte turinį, prieš

pradėdami naudoti vejos / žolės pjovėją.

VIKTIG INFORMATION

Läs anvisningarna före användningen och

spara dem för framtida behov.

ВАЖНАЯ ИНФОРМАЦИЯ

Прочитайте перед тем, как включить

триммер, и сохраните для дальнейшего

использования.

VIGTIGE OPLYSNINGER

Du bør læse brugsanvisningen før brug og

gemme til senere henvisning.

OLULINE TEAVE

Enne seadme kasutuselevõtmist lugege

kasutusjuhend läbi ning säilitage see tuleviku

tarbeks.

INFORMACIÓN IMPORTANTE

Léase antes de utilizar y consérvela como

referencia en el futuro

SVARĪGA INFORMĀCIJA

Pirms lietošanas izlasiet un saglabājiet

turpmākām uzziņām.

INFORMAÇÕES IMPORTANTES

Leia antes de utilizar e guarde para consulta

futura

MANUAL DE INSTRUCŢIUNI

Inainte să folosiţi mașina de tuns pentru

prima oară, citiţi cu atenţie manualul de

instrucţiuni pentru a-i înţelege conţinutul.

INFORMAZIONI IMPORTANTI

Leggere prima dell’uso e conservare per

ulteriore consultazione.

ΣΗΜΑΝΤΙΚΕΣ ΠΛΗΡΟΦΟΡΙΕΣ

∆ιαβάστε αυτό το φυλλάδιο πριν από τη

χρήση της συσκευής και φυλάξτε το για

µελλοντική αναφορά.

FONTOS INFORMÁCIÓ

Használat előtt olvassa el, és tartsa meg

későbbi felhasználásra.

ÖNEMLİ BİLGİLER

Kullanmadan önce okuyunuz ve ileride

başvurmak üzere saklayınız.

5012693-01 Contour Cordless 24V Euro.indb 2 16.10.15 11:27

Page is loading ...

A1 A2

CLICK!

B1

B3

B2

B4

G

F

1

2

3

1

C2

C1

CLICK!

D

E

1

3

2

1

2

J

H

2

1

M

√

x

K

K1

K2

L

1

2

3

CLICK!

5

5012693-01 Contour Cordless 24V Euro.indb 5 16.10.15 11:27

P

1

N

O

1

Q

1

2

1

4

3

R

S

T

1

2

X

V

T1

W

Y

6

5012693-01 Contour Cordless 24V Euro.indb 6 16.10.15 11:27

GB DO NOT use liquids for

cleaning.

DE Zur Reinigung KEINE

Flüssigkeiten verwenden.

FR NE PAS utiliser de produit

liquidepour le nettoyage.

NL Voor het reinigen NOOIT

vloeistoffen gebruiken.

NO Flytende midler MÅ IKKE

brukes til rengjøring.

FI ÄLÄ käytä nesteitä puhdista-

miseen.

SE ANVÄND INTE vätskor för

rengöring.

DK BRUG IKKE væske til

rengøring.

ES NO utilice líquidos para la

limpieza.

PT NÃO use líquidos para

limpar.

IT NON usare liquidi per la

pulizia.

HU NE használjon folyadékokat

tisztításra.

PL NIE używać płynów do czy-

szczenia.

CZ K čištění NEPOUŽÍVEJTE

kapaliny.

SK NEPOUŽÍVAJTE na čistenie

tekuté materiály.

SI NE uporabljajte raznih

tekočin za čiščenje.

HR NEMOJTE koristiti tekućine

za čišćenje.

LT Nenaudokite skysčių

valymui.

RU НЕ используйте жидкости

для очистки.

EE ÄRGE kasutage puhastami-

seks vedelikke.

LV Tīrīšanai NEIZMANTOJIET

šķidrumus.

RO NU utilizaţi pentru curăţire

lichide.

TR Temizleme için sıvılar

KULLANMAYIN.

GR MHN καθαρίζετε µε υγρά.

GB For further advice or repairs,

contact your local dealer.

DE Für weitere Empfehlungen

oder Reparaturarbeiten

setzen Sie sich bitte mit

Ihrem örtlichen Händler in

Verbindung.

FR Pour en savoir plus ou pour

toute réparation, contacter

votre revendeurlocal.

NL Voor nadere informatie over

reparaties kunt u contact

opnemen met uw plaatselijke

leverancier.

NO Ta kontakt med din lokale

forhandler angående ytter-

ligere opplysninger eller

reparasjoner.

FI Tarkempia ohjeita tai tieto

korjauksista saat paikalliselta

jälleenmyyjältä.

SE För ytterligare rådgivning eller

reparationer, kontakta din

lokala återförsäljare.

DK For yderlige vejledning eller

reparation skal du kontakte

din lokale forhandler.

ES Si desea consejos adicio-

nales o reparación, contacte

con su distribuidor local.

PT Para orientação adicional

ou reparações, contacte

o seu agente local.

IT Per ulteriori consigli o ripara-

zioni contattare il rivenditore

locale.

HU További tanácsért vagy

javítás szükségessége ese-

tén forduljon a helyi forgal-

mazóhoz.

PL W sprawie porad lub napraw

skontaktować się z miejs-

cowym przedstawicielem.

CZ O radu nebo opravu

požádejte svého místního

prodejce.

SK Ďalšie informácie a opravy

zabezpečí váš lokálny

predajca.

SI Za nadaljnja navodila ali

popravila kontaktirajte

vasega lokalnega prodajalca.

HR Za daljnje savjete ili

popravke, obratite se svom

prodavaču.

LT Norint sužinoti daugiau

patarimų dėl remonto, susi-

siekite su vietiniu prekiautoju.

RU Для получения дальней-

ших консультаций или

для ремонта свяжитесь

с Вашим местным автори-

зованным дилером.

EE Edasisteks nõuanneteks

või hoolduseks pöörduge

kohaliku edasimüüja poole.

LV Lai uzzinātu vairāk par

remontdarbu veikšanu,

sazinieties ar savu vietējo

izplatītāju.

RO Pentru mai multe sfaturi sau

reparaţii, contactaţi reprezen-

tantul local.

TR Ayrıntılı bilgi veya onarımlar

için, yerel satıcınızla temas

kurunuz.

GR Για περαιτέρω συµβουλές

ή επισκευές, επικοινωνήστε

µε τον τοπικό σας αντιπρό-

σωπο.

7

5012693-01 Contour Cordless 24V Euro.indb 7 16.10.15 11:27

ENGLISH – 1

Safety

WARNING. When using the product the safety rules must be followed. For your own safety and that of

bystanders please read these instructions before operating the product. Please keep the instructions safe

for later use.

Explanation of Symbols on the product

Warning

Read the user instructions carefully to make

sure you understand all the controls and what

they do.

Keep others, including children, pets and

bystanders outside the 10 metre hazard zone.

Stop the trimmer immediately if you are

approached.

Wear eye protection

To avoid the possibility of electric shock,

do not use in damp or wet conditions.

Switch off! Remove battery pack before

adjusting or cleaning.

Warning: The cutting line continues to rotate after the

machine has been switched off.

360º

10m

General

1.

This product may be used under super-

vision, or if instruction regarding the safe

use of the product has been provided

and the resulting dangers have been

understood, by children aged 8 and

above, as well as by persons with physi-

cal, sensory or mental disabilities or a

lack of experience and knowledge. Chil-

dren must not be allowed to play with the

product. Cleaning and user maintenance

must not be performed by children with-

out supervision. The use of this product

by young people under the age of 16 is

not recommended.

2. Never allow children or people unfamiliar with the

instructions to use the machine.

3. Stop using the machine while people, especially

children, or pets are nearby.

4. Only use the trimmer in the manner and for the func-

tions described in these instructions.

5. Never operate the trimmer when you are tired, ill or

under the influence of alcohol, drugs or medicine.

6. The operator or user is responsible for accidents or

hazards occurring to other people or their property.

Battery

Cordless Battery Powered Products require special

care.

1. AVOID ACCIDENTAL STARTING. KEEP HANDS AND

FINGERS AWAY FROM THE SWITCH LEVER WHILE

CARRYING THE TRIMMER.

2. Always charge the product indoors and store in a cool

dry place – out of the reach of children.

3. Use only the charger provided with your unit.

Use of any other charger could permanently damage

the battery and the trimmer.

4. Use the charger with standard domestic household

electrical outlets only.

5. Do not abuse the charger or charger cord.

6. Do not use the charger if the charger or charger cord is

damaged.

7. Use the charger indoors only.

8. Do not use the charger outdoors.

9. Store and charge this unit in a cool, dry well ventilated

location and out of the reach of children.

10. Do not charge the battery or use the unit in an explo-

sive or corrosive environment. Avoid areas where

flammable liquids or gases are present to avoid creat-

ing a fire or explosion.

11. Do not attempt to repair the unit including the battery.

Nylon line replacement and cleaning the unit are the

only items suitable for user maintenance.

12. Do not insert any object into the motor area.

Keep free of debris to avoid overheating.

13. Do not incinerate or mutilate the battery. Batteries

contain hazardous chemicals. Dispose of properly.

Preparation

1. While using your product always wear eye protection,

substantial footwear and long trousers. Do not operate

the equipment when barefoot or wearing open sandals.

2. Before using the machine and after any impact, check

for signs of wear or damage and repair as necessary.

3. Inspect the area to be cut before each use. Remove all

objects such as stones, broken glass, nails, wire, string

etc, which can be thrown or become entangled in the

trimmer head.

4. Before use, inspect the area for wildlife, especially

hedgehogs.

5. Check that the cutting head, spool and cap are fitted

correctly.

Use

1. Use the trimmer only in daylight or good artificial light.

2. Avoid operating your trimmer in wet grass, where feasible.

3. Take care in wet grass, you may lose your footing.

4. On slopes, be extra careful of your footing and wear

non-slip footwear.

5. Do not walk backwards when trimming, you could trip.

Walk, never run.

6. Never operate the trimmer with damaged guards or

without guards in place.

7. Never fit metal cutting elements.

8. Keep hands and feet away from the cutting means at

all times and especially when switching on the motor.

9. Keep cutting head below waist level.

10. Do not lean over the trimmer guard whilst trimming or

edging – objects may be thrown by the cutting line.

11. Beware of cut-off pieces of nylon line ejected during use.

12. If you hit an object, do not use your trimmer until you

are sure that the entire trimmer is in a safe operating

condition.

13. If the trimmer starts to vibrate abnormally, check imme-

diately. Excessive vibration can cause injury.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure the

trimmer is in safe working condition.

2. Replace worn or damaged parts for safety.

5012693-01 Contour Cordless 24V Euro.indb 1 16.10.15 11:27

ENGLISH – 2

3. Only use the replacement cutting line specified for this

product.

4. Only use replacement parts and accessories recom-

mended by Husqvarna UK Ltd.

5. After any maintenance in dealing with the cutting line,

always return the product to its normal operating posi-

tion before switching on.

6. To avoid the risk of injury keep fingers and hands clear

of the line cutter on the leading edge of the guard.

7. Clean unit with a dry cloth. Never use metal objects to

clean the unit.

8. Inspect and maintain the trimmer regularly.

Any repairs must be carried out by an authorised

repairer.

9. Store the product in a cool, dry place and out of reach

of children. Do not store the product outdoors.

10. Allow the product to cool for at least 30 minutes before

storing.

Battery Pack Care

1. If over a period of time the Battery Pack quickly runs

down after a full 6 hour charging period, a

replacement Battery Pack is needed.

2. There will be some charge present in the Battery Pack

but to ensure maximum running time, charge your

Battery Pack for 6 hours before first use.

3. To prevent permanent Battery Pack damage, never

store in a discharged condition.

4. Contact your local approved service centre/dealer/

distributor for a replacement Battery Pack and for safe

disposal of your old Battery Pack.

5. Battery

24 Volt 1.6 AmpHour “High Power”

Sealed for Life No maintenance required

• IMPORTANT

DISPOSE OF YOUR OLD BATTERY PACK SAFELY

DO NOT CUT OPEN, BURN OR INCINERATE.

Winter Storage

1. Fully charge for 6 hours before winter storage.

2. Re-charge the Battery Pack every 3 to 4 months for

a full 6 hour charging period to top up the battery

charge during winter storage.

3. Avoid extended storage without re-charge.

4. Store in a cool dry place.

For further information on Battery Pack replacement

contact your local dealer.

Battery Pack

Assembly of Switch Handle to Tube (A1)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the switch handle.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Assembly of Trimmer Head to Tube (A2)

• Ensure that the internal cable is not twisted.

1. Insert the tube into the trimmer head.

2. Push until it clicks into position.

• ENSURE THAT THE TUBE IS FULLY LOCATED BY

ATTEMPTING TO REMOVE IT.

Wheel Assembly (B1) & (B2)

1. Attach the wheel to the trimmer making sure that it is

located into the BOTTOM groove on the trimmer head

as illustrated in Fig B1.

2. Clip the wheel together on each side making sure it is

secure (B2).

3. The wheel should turn freely.

Plant Guard Assembly (B3) & (B4)

1. Open the plant guard as illustrated in Fig B3 and place

into the TOP groove on the trimmer head. Rotate the

plant guard clockwise until it CLICKS into its parked

position (B4).

Safety Guard Assembly (C1) & (C2)

1. Locate the safety guard over the cutting head. Ensure

the nylon line is fed through the hole in the safety guard

as illustrated in Fig C1.

2. Push into location and turn safety guard in the direction

illustrated in Fig C2, until a click is heard and the safety

guard is securely locked in position.

• ENSURE THE SAFETY GUARD IS SECURELY IN

PLACE BY ATTEMPTING TO TWIST GUARD.

Steady Handle Assembly (D)

1. Pull the steady handle release lever towards the handle

grip.

2. Depress the two buttons on the side of the steady

handle.

3. Locate the buttons into the main handle and release the

lever.

4. Adjust the steady handle to the most comfortable

operating position by pulling the release lever and

moving the handle.

Height Adjustment (E)

1. Turn height adjuster (E1) in the direction indicated to

un-lock (E2).

2. Adjust the length of the tube to the most comfortable

operating position.

3. Turn height adjuster in the opposite direction to

lock (E3).

• ENSURE THAT THE TUBE IS FULLY SECURED.

Assembly Instructions

Initial Charging Procedure

1. Use the charger indoors only.

2. Ensure the charger is not exposed to moisture. Keep

the charger and the Battery Pack dry at all times. Keep

the charger well ventilated during charging.

3. Attach the charger connector (F1) to the Battery Pack.

4. Plug the charger (F2) into a suitable household electrical

wall socket and switch on.

5. The red indicator lamp (F3) glows continuously during

charging.

6. Full charge will be achieved in 3 hours after which the

indicator lamp on the charger (F3) will turn to green.

During charging the charger becomes warm. This is

normal and means the charger is operating correctly.

Re-Charging the Battery Pack

1. Re-charge the Battery Pack as soon as the cutting

power of your trimmer begins to die and slow down.

2. Avoid running the Battery Pack into “deep” discharge,

i.e. avoid flattening the Battery Pack completely.

3. Follow the procedure outlined in the Initial Charging

Procedure.

4. Charging the Battery Pack according to these instruc-

tions should ensure maximum battery life.

Battery Pack Assembly (G)

1. Attach the Battery Pack as illustrated in Fig G, ensuring

that it clicks into position and is located firmly.

2. To remove, press the two buttons (G1) on either side of

the Battery Pack and slide off.

Charging the Battery Pack

5012693-01 Contour Cordless 24V Euro.indb 2 16.10.15 11:27

ENGLISH – 3

• WARNING

• The use of eye protection is recommended.

Do not lean over the trimmer whilst trimming or

edging, objects may be thrown by the cutting line.

Do not allow cutting head to rest on the ground.

Do not overload your trimmer.

Overloading can be avoided by making sure the

motor speed does not drop unduly.

REMOVE THE BATTERY PACK BEFORE

ATTEMPTING ANY MAINTENANCE OR

ADJUSTMENT.

• BEFORE USE

Make sure that the line is fed out.

• Make sure motor is up to full speed before

trimming or edging.

How to trim

1. Hold as illustrated in Fig H.

2. To start, squeeze the safety lock-off (H1) and then the

switch lever (H2).

3. Cut with nylon line at an angle using the tip (J).

4. Swing trimmer in and out of the cutting area taking

small cuts (K).

5. Line is fed out automatically every time the trimmer head

stops rotating and returns to operating speed.

• Extra line can be fed out manually as described in

Manual line feed

6. To stop your trimmer release the switch lever.

The cutting head will stop in approximately one second.

Using the Plant & Tree Guard

The Plant and Tree guard allows the trimming of grass

close to plants and trees without damaging them with the

cutting line.

1. Rotate the guard into it’s forward position as illustrated

in Fig K1.

2. Use the trimmer around trees (K2) and near plants.

How to edge

1. Ensure the plant guard is in the PARK position.

2. To convert to edging mode, press button (L1) and twist

head (L2). An audible “click” will confirm that the head is

locked.

3. Hold as illustrated in Fig H.

4. To start, squeeze the safety lock-off (H1) and then the

switch lever (H2).

5. Rest edger on wheel for extra stability and line up the

edge of the lawn. Edge in direction indicated in Fig M.

6. To stop your trimmer release the switch lever.

7. To return to trimming mode, press button and twist

head back the opposite way. An audible “click” will

confirm that the head is locked.

• When edging, ensure that the edging wheel is

always resting on the grass (and not on the path/

driveway).

Using the Shrubbing position

1. By pressing the lever (N1) with your foot, the handle can

be lowered into three different positions to enable the

use of the product under shrubs and low obstacles (O).

How to trim and edge

How the automatic line feed works (P)

1. When initially switching on the trimmer, a small length of

line is fed out.

2. A ‘clattering’ noise will be heard when the nylon line hits

the line cutter (P1). DO NOT BE ALARMED this is

quite normal. After approximately 5 seconds the line

will be cut to the correct length and the noise will reduce

as the motor reaches full speed.

• Make sure the motor is up to full speed before

trimming or edging.

3. If the noise of the nylon line being cut cannot be heard,

more line will need to be fed out.

4. To feed more line, it is first necessary to to allow the

motor to stop completely, then re-start, allowing the

motor to reach full speed.

5. Repeat step 4. until you hear the line hitting against the

cutter. (Do not repeat this procedure more than

6 times.)

6. If problems are experienced with the automatic line feed

refer to Fault Finding Chart.

Auto Line Feed System

To manually feed the nylon line (Q)

1. If required line can be fed out manually.

2. To operate, press and release manual line feed

button (Q1), whilst gently pulling on the line until it

reaches the line cutter.

3. If the line extends past the line cutter, too much line has

been fed out.

4. If too much line is fed out, remove the spool cap and

click spool anti-clockwise until the line is at the desired

length.

Manual line feed

To remove spool cap

1. Press and hold in the two cap release latches (R1).

2. Pull cap away from the spoolholder (R3).

When refitting the spool cap (R2)

1. Keep all areas of the cap (R2) and spoolholder (R3)

clean. Failure to do so may prevent the cap being

securely located in the spoolholder.

2. Replace the cap, pressing firmly DOWN towards the

spoolholder to ensure cap is fully located.

3. Check that the cap is correctly fitted by trying to remove

it without depressing the two latches.

To replace nylon line

For your convenience it is recommended you buy spool (R4)

and line complete. Nylon line only is also available.

Both are available from your local dealer.

To fit spool and line complete:

1. Remove old spool (R4).

2. Place new spool into spoolholder (R3) with cut out

area of the spool (S1) in line with eyelet as shown in

Fig S2.

3. Release line from cleat (T1) and feed line through

eyelet (S).

• Ensure spool (R4) is fully located by gently rotating

it during fitment, whilst keeping the spoolholder

(R3) steady.

4. Refit the cap (R2).

To fit nylon line only:

• Remember! Your product is designed to use only

nylon line with a maximum diameter of 1.5mm.

Use only genuine Flymo nylon line.

1. Take approximately 10 metres of line. Insert 15mm

of line into the hole in the spool (T) and wind line in the

direction of the arrows on the top of the spool. Leave

approximately 100mm of line unwound and place into

cleat as illustrated in Fig T1.

2. Care should be taken to ensure that the line is neatly

coiled on the spool. Failure to do so will impair the effi-

ciency of the automatic line feed.

3. Then fit spool as described in ‘To fit spool and line

complete’, section above.

Always return the product to its normal operating

position before switching on.

Cutting Head

5012693-01 Contour Cordless 24V Euro.indb 3 16.10.15 11:27

ENGLISH – 4

Fault Finding Chart

WARNING: Remove the Battery Pack before attempting any maintenance or adjustment.

FAULT

CHECK ACTION

Is the automatic line feed working?

Manually feed out line.

SEE “MANUAL LINE FEED”

Is the line fed out and visible?

Has line been removed from cleat?

Remove cap and spool, free line and re-fit

spool and cap. SEE “CUTTING HEAD”

The line may be jammed on the spool.

Rewind line to remove crossed loops.

Check that line is in correct section of spool.

Is the manual line feed working?

Has too much line been fed out? SEE “MANUAL LINE FEED”

Contact your local approved Service Centre

or Husqvarna Customer Service.

Is the line cutter missing from

the safety guard?

Contact Husqvarna Customer Service

No

Yes

LINE NOT FEEDING

OR

LINE TOO SHORT

OR

TRIMMER VIBRATES

CONTINUOUS CLATTERING

NOISE

LINE SNAPS

CONTINUOUSLY

IF NONE OF THE ABOVE

OR IF FAULT PERSISTS

Has the motor reached full speed

before use?

No

Allow the motor to reach full speed

before use.

Are you using the trimmer correctly?

?

Only use tip of nylon line to trim.

SEE “HOW TO TRIM AND EDGE”

Is the line jamming on the spool?

Yes

Rewind the line on the spool, if symptoms

still persist, change spool and line.

Clean wheel and groove on trimmer head. SEE “MAINTENANCE”

WHEEL STOPS TURNING

• WARNING

Remove the Battery Pack, before attempting

any maintenance or adjustment. Cutting head

con tinues to rotate after the trimmer has been

switched off. Keep fingers and hands clear of

the line cutter on leading edge of guard.

Caring for your Contour

After you have finished using your Flymo Contour follow

the procedure below:

1. Never clean your trimmer with water, cleaning fluids,

or solvents, just remove debris with a suitable tool,

a soft brush or dry cloth.

2. Using a soft brush, clean around the inside of the safety

guard, the cutting head (V) and the motor housing air

vents (W).

3. Remove the wheel by pressing one of the buttons.

Clean the wheel (X) and groove (Y) on the trimmer head

with a soft brush.

4. Attach wheel as described in Wheel Assembly.

5. Inspect the trimmer carefully, especially the parts of the

cutting head.

6. If your trimmer is damaged in any way contact your

local Husqvarna service centre.

• Never use a damaged trimmer.

Storage

1. Store in a cool, dry place and out of reach of children.

Do not store outdoors.

2. Allow the product to cool for at least 30 minutes before

storing.

Maintenance

• Awareness of the environment must be considered

when disposing of ‘end-of-life’ product.

• If necessary, contact your local authority for disposal

information.

BATTERY DISPOSAL

• The battery must be removed from the product before

disposal (See Battery Replacement Section)

• This product contains a NiMH battery and should not be

discarded with normal household waste at the end of its

life.

• The battery should be taken to an Authorised Service

Centre or your local Recycling Station.

• Do NOT dispose of battery to water.

• NiMH batteries can be harmful and should be disposed

of through the recognised recycling facility in accord-

ance with European Regulations.

• Do NOT incinerate.

The symbol

on the product or on its packaging indi-

cates that this product may not be treated as household

waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic

equipment.

By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the envi-

ronment and human health, which could otherwise be

caused by inappropriate waste handling of this product.

For more detailed information about recycling of this

product, please contact your local council office, your

household waste disposal service or the shop where you

purchased the product.

Environmental Information

• Your product is uniquely identified by a silver and black product rating label.

• We strongly recommend that your product is serviced at least every twelve months, more often in a professional

application.

Service Recommendations

5012693-01 Contour Cordless 24V Euro.indb 4 16.10.15 11:27

ENGLISH – 5

Spool and Line

Reference no.: FLY047 Part no.: 510747890

Replacement Parts

If any part is found to be defective due to faulty manufac-

ture within the guarantee period, Husqvarna UK Ltd.,

through its Authorised Service Repairers will effect the

repair or replacement to the customer free of charge pro-

viding:

(a) The fault is reported directly to the Authorised Repairer.

(b) Proof of purchase is provided.

(c) The fault is not caused by misuse, neglect or faulty

adjustment by the user.

(d) The failure has not occurred through fair wear and tear.

(e) The machine has not been serviced or repaired, taken

apart or tampered with by any person not authorised

by Husqvarna UK Ltd..

(f) The machine has not been used for hire.

(g) The machine is owned by the original purchaser.

(h) The machine has not been used commercially.

* This guarantee is additional to, and in no way diminish-

es the customers statutory rights.

Failures due to the following are not covered, therefore it is

important that you read the instructions contained in this

Operator’s Manual and understand how to operate and

maintain your machine:

Failures not covered by guarantee

* Replacing Nylon Line.

* Failures as a result of not reporting an initial fault.

* Failures as a result of sudden impact.

* Failures as a result of not using the product in

accordance with the instructions and recommenda-

tions contained in this Operator's Manual.

* Machines used for hire are not covered by this

guarantee.

* The following items listed are considered as wearing

parts and their life is dependent on regular mainte-

nance and are, therefore not normally subject to a valid

warranty claim: Nylon Line, Spool and Line.

* Caution!

Husqvarna UK Ltd. does not accept liability under the

warranty for defects caused in whole or part, directly or

indirectly by the fitting of replacement parts or addition-

al parts that are not either manufactured or approved

by Husqvarna UK Ltd., or by the machine having been

modified in any way.

Guarantee & Guarantee Policy

Husqvarna AB, S-561 82, Huskvarna, Sweden

Declare under our sole responsibility that the product(s);

Designaion ............................................... Lawn Trimmer

Designation of Type(s ............................... CCTE25

Identification of Series ............................... See Product Rating Label

Year of Construction ................................. See Product Rating Label

Conforms to the essential requirements & provisions of the following EC Directives:

2006/42/EC, 2006/95/EC, 2004/108/EC, 2000/14/EC, 2011/65/EU

based on the following EU harmonized standards applied:

EN 60335-1, EN 60335-2-91, EN 60335-2-29, EN 62233, EN 55014-1, EN 55014-2

The maximum A weighted sound pressure level L

pA

at the operator’s position, measured according to EN 60335-2-91

is given in the table.

The maximum hand / arm vibration weighted value a

h

measured according to EN 60335-2-91 on a sample of the above

product(s) is given in the table.

2000/14/EC: The Measured Sound Power L

WA

& Guaranteed Sound Power L

WA

values are according to the tabulated

figures.

Conformity Assessment Procedure ........... Annex VI

Notified Body ............................................ Intertek, Davy Avenue,

Knowlhill,

Milton Keynes,

Bucks, MK5 8NL,

England

Ulm, 05.11.2013

P. Lameli

Chief Technical Officer

Keeper of technical documentation

EC Declaration of Conformity

Type

Width of Cut (cm)

Speed of Rotation of Cutting Device (rpm)

Measured Sound Power L

WA

(dB(A))

Guaranteed Sound Power L

WA

(dB(A))

Sound pressure L

pA

(dB(A))

Uncertainty K

pA

(dB(A))

Hand / arm vibration a

h

(m/s

2

)

Uncertainty K

ah

(m/s

2

)

Weight (Kg)

CCTE25

25

8,500

82

96

74.4

2.5

1.8

1.5

3.2

5012693-01 Contour Cordless 24V Euro.indb 5 16.10.15 11:27

Page is loading ...

Deutschland / Germany

GARDENA GmbH

Central Service

Hans

-

Lorenser

-

Straße 40

D

-

89079 Ulm

Produktfragen:

(+49) 731 490

-

123

Reparaturen:

(+49) 731 490

-

290

service

@gardena.com

Albania

COBALT Sh.p.k.

Rr. Siri Kodra

1000 Tirana

Argentina

Husqvarna Argentina S.A.

Av.del Libertador 5954

–

Piso 11

–

Torre B

(C1428ARP) Buenos Aires

Phone: (+54) 11 5194 5000

info.gardena

@

ar.husqvarna.com

Armenia

Garden Land Ltd.

61 Tigran Mets

0005 Yerevan

Australia

Husqvarna Australia Pty. Ltd.

Locked Bag 5

Central Coast BC

NSW 2252

Phone: (+61) (0) 2 4352 7400

customer.service

@

husqvarna.com.au

Austria / Österreich

Husqvarna Austria GmbH

Industriezeile 36

4010 Linz

Tel.: (+43) 732 77 01 01

-

485

service.gardena

@

husqvarnagroup.com

Azerbaijan

Firm Progress

a. Aliyev Str. 26A

1052 Baku

Belgium

GARDENA Belgium NV/SA

Sterrebeekstraat 163

1930 Zaventem

Phone: (+32) 2 7 20 92 12

Mail: info

@gardena.be

Bosnia / Herzegovina

SILK TRADE d.o.o.

Industrijska zona Bukva bb

74260 Tešanj

Brazil

Husqvarna do Brasil Ltda

Av. Francisco Matarazzo,

1400

–

19º andar

São Paulo

–

SP

CEP: 05001

-

903

Tel: 0800

-

112252

marketing.br.husqvarna

@

husqvarna.com.br

Bulgaria

Хускварна България ЕООД

Бул. „Андрей Ляпчев” Nº 72

1799 София

Тел.: (+ 359) 02/9753076

www.husqvarna.bg

Canada / USA

GARDENA Canada Ltd.

100 Summerlea Road

Brampton, Ontario L6T 4X3

Phone: (+1) 905792 93 30

info

@gardenacanada.com

Chile

Maquinarias Agroforestales

Ltda. (Maga Ltda.)

Santiago, Chile

Avda. Chesterton

# 8355 comuna Las Condes

Phone: (+56) 2 202 4417

Dalton

@maga.cl

Zipcode: 7560330

Temuco, Chile

Avda. Valparaíso # 01466

Phone: (+56) 45 222 126

Zipcode: 4780441

China

Husqvarna (China) Machinery

Manufacturing Co., Ltd.

No. 1355, Jia Xin Rd.,

Ma Lu Zhen, Jia Ding Dist.,

Shanghai

201801

Phone: (+86) 21 59159629

Domestic Sales

www.gardena.com.cn

Colombia

Husqvarna Colombia S.A.

Calle 18 No. 68 D

-

31, zona

Industrial de Montevideo

Bogotá, Cundinamarca

Tel. 571 2922700 ext. 105

jairo.salazar

@

husqvarna.com.co

Costa Rica

Compania Exim

Euroiberoamericana S.A.

Los Colegios, Moravia,

200 metros al Sur del Colegio

Saint Francis

–

San José

Phone: (+506) 297 68 83

exim_euro

@racsa.co.cr

Croatia

SILK ADRIA d.o.o.

Josipa Lončara 3

10090 Zagreb

Phone: (+385) 1 3794 580

silk.adria

@zg.t

-

com.hr

Cyprus

Med Marketing

17 Digeni Akrita Ave

P.O. Box 27017

1641 Nicosia

Czech Republic

Husqvarna Česko s.r.o.

Türkova 2319/ 5b

149 00 Praha 4 – Chodov

Bezplatná infolinka:

800 100 425

servis

@cz.husqvarna.com

Denmark

GARDENA / Husqvarna

Consumer Outdoor Products

Salgsafdelning Danmark

Box 9003

S

-

200 39 Malmö

info

@gardena.dk

Dominican Republic

BOSQUESA, S.R.L

Carretera Santiago Licey

Km. 5 ½

Esquina Copal II.

Santiago

Dominican Republic

Phone: (+809) 736

-

0333

joserbosquesa

@claro.net.do

Ecuador

Husqvarna Ecuador S.A.

Arupos E1

-

181 y 10 de

Agosto

Quito, Pichincha

Tel. (+593) 22800739

francisco.jacome

@

husqvarna.com.ec

Estonia

Husqvarna Eesti OÜ

Consumer Outdoor Products

Kesk tee 10, Aaviku küla

Rae vald

Harju maakond

75305 Estonia

kontakt.etj

@husqvarna.ee

Finland

Oy Husqvarna Ab

Consumer Outdoor Products

Lautatarhankatu 8 B / PL 3

00581 HELSINKI

info

@gardena.fi

France

Husqvarna France

9/11 Allée des pierres mayettes

92635 Gennevilliers Cedex

France

http://www.gardena.com/fr

N° AZUR: 0 810 00 78 23

(Prix d’un appel local)

Georgia

ALD Group

Beliashvili 8

1159 Tleilisi

Great Britain

Husqvarna UK Ltd

Preston Road

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6UP

info.gardena

@

husqvarna.co.uk

Greece

Π.ΠΑΠΑΔΟΠΟΥΛΟΣ ΑΕΒΕ

Λεωφ. Αθηνών 92

Αθήνα

Τ.Κ.104 42

Ελλάδα

Τηλ. (+30) 210 51 93100

info

@papadopoulos.com.gr

Hungary

Husqvarna Magyarország Kft.

Ezred u. 1

-

3

1044 Budapest

Telefon: (+36) 1 251

-

4161

vevoszolgalat.husqvarna

@

husqvarna.hu

Iceland

Ó. Johnson & Kaaber

Tunguhalsi 1

110 Reykjavik

ooj

@ojk.is

Ireland

Husqvarna UK Ltd

Preston Road

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6UP

info.gardena

@

husqvarna.co.uk

Italy

Husqvarna Italia S.p.A.

Via Como 72

23868 VALMADRERA (LC)

Phone: (+39) 0341.203.111

info

@gardenaitalia.it

Japan

KAKUICHI Co. Ltd.

Sumitomo Realty &

Development Kojimachi

BLDG., 8F

5

-

1 Nibanncyo

Chiyoda

-

ku

Tokyo 102

-

0084

Phone: (+81) 33 264 4721

m_ishihara

@kaku

-

ichi.co.jp

Kazakhstan

LAMED Ltd.

155/1, Tazhibayevoi Str.

050060 Almaty

IP Schmidt

Abayavenue 3B

110 005 Kostanay

Korea

Kyung Jin Trading CO.,LTD.

107-4, SunDuk Bld.,

YangJae-dong,

Seocho-gu,

Seoul, (zipcode: 137-891)

Phone: (+82) (0)2 574-6300

Kyrgyzstan

Alye Maki

av. Moladaya Guardir J 3

720014

Bishkek

Latvia

Husqvarna Latvija

Consumer Outdoor Products

Bākūžu iela 6

LV-1024 Rīga

info

@husqvarna.lv

Lithuania

UAB Husqvarna Lietuva

Consumer Outdoor Products

Ateities pl. 77C

LT

-

52104 Kaunas

centras

@

husqvarna.lt

Luxembourg

Magasins Jules Neuberg

39, rue Jacques Stas

Luxembourg

-

Gasperich 2549

Case Postale No. 12

Luxembourg 2010

Phone: (+352) 40 14 01

api

@neuberg.lu

Mexico

AFOSA

Av. Lopez Mateos Sur # 5019

Col. La Calma 45070

Zapopan, Jalisco

Mexico

Phone: (+52) 33 3818

-

3434

icornejo

@afosa.com.mx

Moldova

Convel S.R.L.

290A Muncesti Str.

2002 Chisinau

Netherlands

GARDENA Nederland B.V.

Postbus 50176

1305 AD ALMERE

Phone: (+31) 36 521 00 00

info

@gardena.nl

Neth. Antilles

Jonka Enterprises N.V.

Sta. Rosa Weg 196

P.O. Box 8200

Curaçao

Phone: (+599) 9 767 66 55

pgm

@jonka.com

New Zealand

Husqvarna New Zealand Ltd.

PO Box 76

-

437

Manukau City 2241

Phone: (+64) (0) 9 9202410

support.nz

@husqvarna.co.nz

Norway

GARDENA

Husqvarna Consumer

Outdoor Products

Salgskontor Norge

Kleverveien 6

1540 Vestby

info

@gardena.no

Peru

Husqvarna Perú S.A.

Jr. Ramón Cárcamo 710

Lima 1

Tel : (+51) 1 3320400 ext.416

juan.remuzgo

@

husqvarna.com

Poland

Husqvarna

Poland Spółka z o.o.

ul. Wysockiego 15 b

03

-

371 Warszawa

Phone: (+ 48) 22 330 96 00

gardena

@husqvarna.com.pl

Portugal

Husqvarna Portugal , SA

Lagoa

-

Albarraque

2635

-

595 Rio de Mouro

Tel.: (+351) 21 922 85 30

Fax : (+351) 21 922 85 36

info

@gardena.pt

Romania

Madex International Srl

Soseaua Odaii 117

-

123,

RO 013603 Bucure

ş

ti, S1

Phone: (+ 40) 21 352.76.03

madex

@ines.ro

Russia / Россия

ООО „Хускварна“

141400, Московская обл.,

г. Химки,

улица Ленинградская,

владение 39, стр.6

Бизнес Центр

„Химки Бизнес Парк“,

помещение ОВ02_04

http: //www.gardena.ru

Serbia

Domel d.o.o.

Autoput za Novi Sad bb

11273 Belgrade

Phone: (+381) 1 18 48 88 12

miroslav.jejina

@

domel.rs

Singapore

Hy

-

Ray PRIVATE LIMITED

40 Jalan Pemimpin

#02

-

08 Tat Ann Building

Singapore 577185

Phone: (+65) 6253 2277

shiying

@hyray.com.sg

Slovak Republic

Husqvarna Česko s.r.o.

Türkova 2319/ 5b

149 00 Praha 4 – Chodov

Bezplatná infolinka:

800 154 044

servis

@sk.husqvarna.com

Slovenia

Husqvarna Austria GmbH

Industriezeile 36

4010 Linz

Tel.: (+43) 732 77 01 01

-

485

service.gardena

@

husqvarnagroup.com

South Africa

Husqvarna

South Africa (Pty) Ltd

Postnet Suite 250

Private Bag X6,

Cascades, 3202

South Africa

Phone: (+27) 33 846 9700

info

@gardena.co.za

Spain

Husqvarna España S.A.

Calle de Rivas nº10

28052 Madrid

Phone: (+34) 91 708 05 00

atencioncliente

@gardena.es

Suriname

Agrofix n.v.

Verlengde Hogestraat #22

Phone: (+597) 472426

agrofix

@sr.net

Pobox : 2006

Paramaribo

Suriname

–

South America

Sweden

Husqvarna AB

S

-

561 82 Huskvarna

info

@gardena.se

Switzerland / Schweiz

Husqvarna Schweiz AG

Consumer Products

Industriestrasse 10

5506 Mägenwil

Phone: (+41) (0) 62 887 37 90

info

@gardena.ch

Turkey

GARDENA Dost Diş Ticaret

Mümessillik A.

Ş

.

Sanayi Çad. Adil Sokak

No: 1/B Kartal

34873 Istanbul

Phone: (+90) 216 38 93 939

info

@gardena

-

dost.com.tr

Ukraine / Україна

ТОВ «Хусварна Україна»

вул. Васильківська, 34,

офіс 204

-

г

03022, Київ

Тел. (+38) 044 498 39 02

info

@gardena.ua

Uruguay

FELI SA

Entre Ríos 1083 CP 11800

Montevideo

–

Uruguay

Tel: (+598) 22 03 18 44

info

@felisa.com.uy

Venezuela

C

orporación Casa y Jardín C.A.

Av. Caroní, Edif. Trezmen, PB.

Colinas de Bello Monte.

1050 Caracas.

Tlf: (+58) 212 992 33 22

info

@casayjardin.net.ve

1885

-

20.960.03 / 0915

©

GARDENA

Manufacturing GmbH

D-89070 Ulm

http://www.gardena.com

136

5012963-01/1015

Husqvarna AB

S-561 82 Huskvarna

Sweden

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.

Flymo

®

and other product and feature names are registered or unregistered trademarks of Flymo S.A.

5012693-01 Contour Cordless 24V Euro.indb 6 16.10.15 11:28

Flymo Contour Cordless 24V Owner's manual

This manual is also suitable for

Flymo Contour Cordless 24V Owner's manual

in other languages

Related papers

Other documents