Emax HP15V120Y3PK-460 Operating instructions

Type
Operating instructions

This manual is also suitable for

UNLESS OTHERWISE SPECIFIED
DIM. TOLERANCES ARE AS FOLLOWS:
X XX XXX XXXX
INCH
.1 .02 .005 .0005
mm
0.5 0.13 0.013
ANG.
.50 DEG
REMOVE BURRS & BREAK SHARP EDGES:
INCH .003 - .015 mm 0.1 - 0.4
CORNER FILLETS TO :
INCH .020 mm 0.5
MACHINE SURFACES :
INCH 125 mm
METRIC DIMS. SHOWN IN [BRACKETS]
A
B
C
D D
123
C
45678
B
A
12345678
APPD
REV BY
DESCRIPTION
DATE
REV
DATE
FLATNESS
STRAIGHTNESS
ANGULARITY
PERPENDICULARITY (SQUARENESS)
PARALLELISM
ROUNDNESS (CIRCULARITY)
CYLINDRICITY
PROFILE OF ANY SURFACE
PROFILE OF ANY LINE
RUNOUT
TRUE POSITION
CONCENTRICITY
SYMMETRY
CONFIDENTIAL : THIS DRAWING AND ITS INFORMATION ARE
THE EXCLUSIVE AND CONFIDENTIAL PROPERTY OF AIRBASE
INDUSTRIES AND ARE NOT TO BE DISCLOSED,
DUPLICATED, DISTRIBUTED OR OTHERWISE USED WITHOUT
THE WRITTEN CONSENT OF AIRBASE INDUSTRIES
- ALL RIGHTS RESERVED.
DR BY:
APPD:
DR BY DATE:
APPD DATE:
THIRD ANGLE
PROJECTION
EDS DATE
FORMAT REV
DESCRIPTION
SIZE
DWG NO
GEOMETRIC CHARACTERISTICS & SYMBOLS
SHEET
ASME Y14.5 1994
1000 CASS DR
CLAYTON, OHIO
45315
A
SW
1
2
3
4
5
6
7
8
9
10
11
12
10
13
14
15
16
17
18
19
20
21
22
23
24
25
26
26
28
29
30
31
32
32
30
33
34
35
36
37
27
25
26
28
24
32
32
30
29
30
33
34
35
36
37
38
39
31
40
41
42
43
44
45
45
49
48
50
51
27
25
26
24
52
52
54
55
56
57
58
59
60
61
52
38
42
42
54
55
56
57
58
59
43
44
40
41
45
45
48 49
50
518283
46
47
51
50
81
78
50
82
83
80
78
7879
84
85
87
88
40
41
74
75
74
76
72 73
61
35
34
71
68
69
62
53
64
65
68
70
71
71
67
51
33
90
A
XX
XX-XX
XXXX
xx-xx-
ALAN CAIN
04/05/2015
04/05/2015
D
EC15 ASSY
1 OF 2
XXXXXX
UNLESS OTHERWISE SPECIFIED
DIM. TOLERANCES ARE AS FOLLOWS:
X XX XXX XXXX
INCH
.1 .02 .005 .0005
mm
0.5 0.13 0.013
ANG.
.50 DEG
REMOVE BURRS & BREAK SHARP EDGES:
INCH .003 - .015 mm 0.1 - 0.4
CORNER FILLETS TO :
INCH .020 mm 0.5
MACHINE SURFACES :
INCH 125 mm
METRIC DIMS. SHOWN IN [BRACKETS]
A
B
C
D D
123
C
45678
B
A
12345678
APPD
REV BY
DESCRIPTION
DATE
REV
DATE
FLATNESS
STRAIGHTNESS
ANGULARITY
PERPENDICULARITY (SQUARENESS)
PARALLELISM
ROUNDNESS (CIRCULARITY)
CYLINDRICITY
PROFILE OF ANY SURFACE
PROFILE OF ANY LINE
RUNOUT
TRUE POSITION
CONCENTRICITY
SYMMETRY
CONFIDENTIAL : THIS DRAWING AND ITS INFORMATION ARE
THE EXCLUSIVE AND CONFIDENTIAL PROPERTY OF AIRBASE
INDUSTRIES AND ARE NOT TO BE DISCLOSED,
DUPLICATED, DISTRIBUTED OR OTHERWISE USED WITHOUT
THE WRITTEN CONSENT OF AIRBASE INDUSTRIES
- ALL RIGHTS RESERVED.
DR BY:
APPD:
DR BY DATE:
APPD DATE:
THIRD ANGLE
PROJECTION
EDS DATE
FORMAT REV
DESCRIPTION
SIZE
DWG NO
GEOMETRIC CHARACTERISTICS & SYMBOLS
SHEET
ASME Y14.5 1994
1000 CASS DR
CLAYTON, OHIO
45315
A
SW
89
A
XX
XX-XX
XXXX
xx-xx-
W.R. WATKINS
01-10-2012
01-10-2012
D
EC15 ASSY
2 OF 2
XXXXXX
  • Page 1 1
  • Page 2 2

Emax HP15V120Y3PK-460 Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI