Simplicity 00776-1 User manual

Brand: Simplicity

Model: 00776-1

Category: High-pressure cleaners

Type: User manual

Simplicity 00776-1 is a 1300 PSI electric high pressure washer with a 1.5 GPM flow rate. This powerful pressure washer is perfect for cleaning decks, patios, siding, and other outdoor surfaces. It comes with a variety of nozzles to choose from, so you can customize the spray to the specific cleaning task. The Simplicity 00776-1 also has a built-in detergent tank, so you can easily add soap to the water stream for added cleaning power.

1300PSI

Double Insulated

Electric High Pressure Washer

Owners Manual

This symbol points out important safety instructions, which, if not followed, could endanger the personal safety

and/or property of yourself and others. Read and follow all instructions in thE manual before attempting to operate

this unit.

Model No. 0776-1 (1.5 gpm High Pressure Washer) Manual No. B1742 Revision 0 (7/17/97)

PRESSURE WASHER

CUSTOMER HELPLINE

1-800-270-1408

HOURS: Mon.-Fri. 8 a.m. to 5 p.m.

(CST)

GENERAC

The Reliable Ones

DANGER!

Risk of electrocution!

 Inspect cord before every use. Do not use if cord is damaged.

 Keep all connections dry and off the ground.

 Do not touch plug with wet hands.

 Double-insulated  When servicing, use only identical replacement parts.

 This product shall only be connected to a power supply receptacle protected by

a Ground Fault Circuit Interrupter (GFCI).

 Read instruction manual before using.

CAUTION!

When using this product, basic precautions should always be fol-

lowed, including the following:

 To reduce the risk of injury, read all instructions before using the product.

WARNING!

To reduce the risk of injury, close supervision is necessary when

product is used near children.

 Know how to stop the product and bleed the pressure quickly. Be thoroughly famil-

iar with controls.

 Stay alert. Watch what you are doing.

 Do not operate the product when fatigued or under the influence of alcohol or drugs.

 Keep operating area clear of all persons.

WARNING!

Risk of injury or injection to persons  Do not discharge stream at per-

sons or animals.

 High pressure hose can develop leaks from wear, kinking, abuse, etc. Water

spraying from a leak is capable of injecting material into skin. Do not point the

pressure washer spray at people or animals.

 Do not overreach or stand on unstable support. Keep good footing and balance

at all times.

 Follow the maintenance instructions specified in the manual.

 This product shall only be connected to a power supply receptacle protected by

a Ground Fault Circuit Interrupter (GFCI). This is done to comply with National

Electrical Code (NFPA 70) and to provide additional protection from risk of elec-

trical shock.

 Save these instructions.

 Operate this pressure washer only in areas away from combustible materials, com-

bustible fumes or dust.

 Some chemicals or detergents may be harmful if inhaled or ingested, causing severe

nausea, fainting or poisoning. The harmful elements may cause property damage

or severe injury.

 Do not allow CHILDREN to operate the Pressure Washer at any time.

 Before starting the Pressure Washer in cold weather, check all parts of the equip-

ment and be sure ice has not formed.

 Units with broken or missing parts, or without protective housing or covers should

NEVER be operated.

DANGER!

Risk of Explosion  Do not spray flammable liquids.

 Never aim the gun at people, animals or plants.

 For household use. For indoor or outdoor use.

 High pressure stream of fluid that this equipment can produce may pierce skin

and its underlying tissues, leading to serious injury and possible amputation.

 High pressure spray can cause paint chips or other particles to become airborne

and fly at high speeds.

 Always wear eye protection when you use this equipment or when you are in vicin-

ity where the equipment is in use.

 Never move the machine by pulling on high pressure hose. Use the handle pro-

vided on the top of the unit.

 Use a respirator or mask whenever there is a chance that vapors may be inhaled.

Read all instructions with the mask so you are certain the mask will provide the

necessary protection against inhaling harmful vapors.

 High pressure spray may damage fragile items including glass. Do not point spray

gun at glass when in the high pressure mode.

 Keep the hose connected to machine or the spray gun while the system is pres-

surized. Disconnecting the hose while the unit is pressurized is dangerous.

 Hold the spray gun firmly in your hand before you start the unit. Do not leave the

pressure washer unattended while the machine is turned on.

 Cleaning area should have adequate slopes and drainage to reduce possibility

of a fall due to slippery surfaces.

 Keep water spray away from electric wiring or fatal electric shock may result.

 Do not by-pass any safety device on this machine.

 Operate and store this unit on a stable surface.

 Inspect hose each time before using it. Check all hoses for cuts, leaks, abrasions,

bulging of cover, damage or movement of couplings. If any of these conditions

exist, replace hose immediately. Never repair high pressure hose. Replace it with

another hose that meets minimum pressure rating of your pressure washer.

 Store in a clean, dry area. Ideally, the unit should be stored in a frost-free room.

SERVICING OF A DOUBLE-INSULATED PRODUCT

In a double-insulated product, two systems of insulation are provided instead of

grounding. No means of grounding is provided on a double-insulated product, nor

should a means for grounding be added.

Servicing a double-insulated product requires extreme care and knowledge of the

system and should be done only by qualified service personnel. Replacement parts

for a double-insulated product must be identical to the parts they replace. use only

genuine replacement parts. A double-insulated product is marked with the words

DOUBLE INSULATION or DOUBLE INSULATED.

The symbol may also be marked on the product.

EXTENSION CORDS

Use only extension cords that are approved for outside use. These extension cords

are identified by a marking ACCEPTABLE FOR USE WITH OUTDOOR APPLI-

ANCES; STORE INDOORS WHILE NOT IN USE. Use only extension cords having

an electrical rating not less than the rating of the product. Do not use damaged exten-

sion cords. Examine extension cord before using and replace if damaged. Do not

abuse extension cord and do not yank on any cord to disconnect it. Keep cord away

from heat and sharp edges. Always disconnect the extension cord from the recep-

tacle before disconnecting the pressure washer from the extension cord.

GENERAC

Generac 1300PSI Electric High Pressure Washer

Save these instructions

IMPORTANT!  SAFETY INSTRUCTIONS  IMPORTANT!

GENERAC

Generac 1300PSI Electric High Pressure Washer

CONGRATULATIONS on your purchase of a GENERAC

electric high pressure washer. It has been designed, engi-

neered and manufactured to give you the best possible

dependability and performance.

Should you experience any problem you cannot easily

remedy, please contact your nearest GENERAC Authorized

Service facility, or call the 18002701408 number listed

on the front of this manual. We have competent, well-

trained technicians and the proper tools to service or repair

this unit.

Please read and retain this manual. The instructions will

enable you to assemble and maintain your high pressure

washer properly. Always observe the SAFETY RULES.

CUSTOMER RESPONSIBILITIES

 Read and observe the safety rules.

 Follow regular schedule in maintaining, caring for and using

your high pressure washer.

 Follow the instructions under Maintenance and Storage

sections of this Owner's Manual.

PRODUCT SPECIFICATIONS

PRESSURE WASHER SPECIFICATIONS

Model

Number 0776-1

Serial

Number_________________________________

Date of

Purchase________________________________

The model and serial numbers will be found on a decal

attached to the pressure washer. You should record both

serial number and date of purchase and keep in a safe place

for future reference

Pressure 1300 psi

Flow Rate 1.5 GPM

Detergent Mix Use undiluted detergent

Water Supply Cold water not to

Temperature exceed 104°F

Motor Brush type (universal)

Rated Voltage 120 volts

Current 14 amperes

GENERAC

Generac 1300PSI Electric High Pressure Washer

CONTENTS OF PACKAGE

High Pressure Washer

High Pressure Hose*

Nozzle Extension*

Foamer*

* These parts are found separately in the parts box within the package.

** These parts are found separately in the parts bag within the parts box.

Goggles*

Spray Gun*

Nozzle Cleaning Kit**

Quick-Connect**

Accessories

Adapter**

PACKAGE

Spray Gun  Controls the application of water onto

cleaning surface with trigger device. Includes safety

latch.

High Pressure Outlet  Connection for high

pressure hose.

Master On/Off Switch  This switch ONLY enables

the Grip Start system to function.

QuickConnect  Easy connection for intake water

supply.

Grip Start System  Pressing and releasing the

spray gun trigger starts and stops the electric motor

in the pressure washer.

Safety Flow System  Electric motor will not start

unless water is supplied to the pump.

Foamer  Used to apply detergent. Mixes water and deter-

gent in outlet water flow.

Accessories Adapter (Not Shown)  This specially designed

connector accommodates the connection of a multipurpose

and rotating brush to the spray gun. Both brushes are sold

separately and are not included with this unit.

Water Inlet  Connection for garden hose. (Note: You need

to use the quickconnect to attach the garden hose to the pres-

sure washer)

Nozzle Extension  Attaches to spray gun.

GENERAC

Generac 1300PSI Electric High Pressure Washer

Read this owners manual before operating your high pressure washer. Compare the illustrations with your high pressure

washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.

Spray Gun

Master On/Off Switch

High Pressure Outlet

Nozzle Extension

Water Inlet

Grip Start System

Safety Flow System

QuickConnect

Foamer

GENERAC

Generac 1300PSI Electric High Pressure Washer

Read these instructions and Operators Manual in its

entirety before you attempt to assemble or operate your

new high pressure washer. Your high pressure washer has,

for the most part, been assembled at the factory. Before you

can operate your new high pressure washer, you must

properly connect the high pressure hose and the water

supply.

If you have any problems with the assembly of your pres-

sure washer, please call the pressure washer helpline at

1-800-270-1408.

TO REMOVE PRESSURE WASHER

FROM CARTON

 Remove parts box.

 Remove parts bag from parts box.

 Remove main unit with attached electrical cord.

Refer to Page 4, Contents of Hardware Pack for an illus-

trated listing of all items included with your pressure

washer. Become familiar with each piece before assembling

the pressure washer. Check all contents against the illustra-

tions on Page 4. If any parts are missing, call the pressure

washer helpline at 1-800-270-1408.

HOW TO SET UP YOUR

PRESSURE WASHER

 Unwind the high pressure hose and attach it to spray gun

(see Figure 1).

 Attach the high pressure hose to the high pressure outlet

and tighten by hand (Figure 2).

 Included with this unit is a quick-connect fitting that you must

attach to the water inlet and your garden hose. You can install

the male connector end by hand but you may need to use

an adjustable wrench to tighten it (Figure 3).

 Check the screen on the female quickconnect. Be sure it is

clean and check for damage. If you see any damage in the

screen, do not use that female quickconnect.

 Attach the female quick connect to your garden hose.

 Attach garden hose to the water inlet using the quickcon-

nect. The quickconnect should lock in place. (Figure 4 on

page 7).

AASSSSEEMMBBLLYY

Figure 1 - Attach Hose to Spray Gun

Figure 2 - Attach High Pressure Hose to Main Unit

Figure 3 - Install Quick Connect

GENERAC

Generac 1300PSI Electric High Pressure Washer

DANGER: When connecting the unit to a power supply

receptacle, use ONLY a receptacle protected by a

Ground Fault Circuit Interrupter (GFCI). This will help

protect against electrical shock.

CAUTION: Before starting you should be sure the

electrical supply is rated at 120 volts, 15 amps.

WARNING: To reduce the risk of electrocution, keep ALL

connections dry and off the ground. DO NOT touch plug

with wet hands.

 We do not recommend that you use extension cords with

this pressure washer. If, however, your application requires

that you need an extension cord, use only extension cords

that are approved for outside use. These extension cords

are identified by a marking ACCEPTABLE FOR USE WITH

OUTDOOR APPLIANCES; STORE INDOORS WHILE NOT

IN USE. Use only extension cords having an electrical

rating not less than the rating of the product. Do not use

damaged extension cords.

 Turn on the water.

NOTE: Water temperature should not exceed 104°F.

DANGER: You must attach the spray gun all hoses

before you start the motor.

 Press the master On/Off Switch to the On position (Figure 5).

DANGER: You must be careful at this point. Anytime you

squeeze the trigger, the motor will start and water will

spray out of the gun.

CAUTION: Before starting the pressure washer, be sure

you are wearing adequate eye protection. Goggles are

included with this unit.

WARNING: Gun kicks back. Use both hands.

DANGER: Risk of injury or injection to people and

animals. DO NOT discharge stream at people or

animals.

 Squeeze trigger to purge pump of system air and impurities.

 Attach nozzle extension to spray gun by aligning the locking

tabs on the extension with the grooves in the gun. Push exten-

sion inward and twist clockwise to lock in place (Figure 6).

 Squeeze trigger to produce spray.

NOTE: Behind the trigger to the gun is a SAFETY LATCH.

You can place this latch as shown in Figure 7 to keep the

washer from accidentally spraying while you are changing

the nozzle head or foamer or performing other tasks.

SSSSEEMMBBLL

Figure 4 - Connect Garden Hose to Water Inlet

Figure 5 - Press the Master ON/OFF Switch to the

ON position.

Figure 6 - Connect the Nozzle Extension to Spray

Gun

Figure 7 - Applying the Safety Latch

GENERAC

Generac 1300PSI Electric High Pressure Washer

STOPPING YOUR PRESSURE

WASHER

 If the pressure washer is running, release the trigger.

DANGER: Releasing the trigger will shut off the motor

but does not shut off the unit. You must also place the

Master On/Off Switch to the OFF position.

 Place Master On/Off switch in OFF position. Simply shutting

OFF motor will not release pressure in the system. Squeeze

the trigger on the gun to relieve the pressure in the hose.

DANGER: Never leave your pressure washer

unattended even when turned off.

HOW TO USE YOUR WASHER

You now should know how to START your pressure washer

and how to STOP it. The information in this section will tell

you how to adjust the spray pattern and apply detergent or

any other cleaning chemicals.

HOW TO USE ADJUSTABLE

NOZZLE

DANGER: Never adjust spray pattern when spraying.

Never put hands in front of spray nozzle to adjust spray

pattern. You could be injured.

On the end of your spray gun is a nozzle that you can twist

from side to side. With the adjustable nozzle you can adjust

the spray configuration to be either concentrated in a stream

or expanded into a fan pattern.

 Twist nozzle counterclockwise when you wish to produce an

expanded stream. Twist nozzle clockwise to produce a

narrow, concentrated stream (Figure 8).

 Point the nozzle toward the ground and press the trigger to

test the pattern (Figure. 9).

 For most effective cleaning, keep spray nozzle between 8 to

24 inches of cleaning surface.

 If you get the spray nozzle too close, especially using high pres-

sure mode, you may damage the cleaning surface.

 Do not get closer than 6 inches when cleaning automobile tires.

APPLYING DETERGENT WITH

FOAMER

IMPORTANT: Use soaps designed specifically for pressure

washers. Household detergents could damage the pump.

DANGER: You MUST attach all hoses and the spray gun

before you start the motor.

WARNING: Before removing any spray gun extension,

be sure to turn off the pressure washer and relieve

pressure by pressing the trigger. You could be injured if

you try to remove an extension if the pressure washer is

running and there is pressure in the system.

Pressure washers are useful cleaning tools designed to

clean almost any surface in two easy steps.

 The first step involves applying an appropriate detergent/sol-

vent solution to penetrate and loosen grime. The detergent

is applied at low pressure to avoid splashing, overspraying

and waste. Leave the solution on surface for 3 to 5 minutes

to allow solution to work.

 The second step involves cleaning the surface you have

prepared with the pressure washer and then rinsing it clean.

Twist Nozzle

Counterclockwise

for Fan Spray

Twist Nozzle

Clockwise for

Narrow Spray.

AASSSSEEMMBBLLYY

Figure 8  Using the Adjustable Nozzle

Figure 9  Testing the Spray Pattern

GENERAC

Generac 1300PSI Electric High Pressure Washer

To apply detergent follow these steps:

 Detach the nozzle extension by pushing in and unlocking it

counterclockwise.

 Remove the bottle from the foamer.

 Align the locking tabs on the foamer with the groves in the

gun. Push inward and twist clockwise to lock in place. (Note:

make sure that the when you lock the foamer into place you

have the hose that connects to the foamer bottle hanging

downward.)

 Prepare your detergent solution as required by your job and

fill bottle with the solution.

 Attach bottle back onto foamer making sure the bottle hangs

down.

 Start washer and apply detergent to a dry surface, starting

from the bottom and working up.

 To rinse, YOU MUST, stop the pressure washer, remove the

foamer and connect the adjustable nozzle extension.

NOTE: Detergents are most effective applied to a dry surface.

TO CLEAN

Start at lower portion of area to be washed and work

upward, using long, even overlapping strokes. Detergent or

degreaser works best when you apply it to a dry surface

first. Let it set for 3-5 minutes before washing and rinsing.

RINSE

Start at the top of area to be rinsed, working down with the

same action as for cleaning.

NOTE: Never use garden hose inlet to siphon detergent or wax.

The warranty of the high pressure washer does not cover

items that have been subjected to operator abuse or negli-

gence. To receive full value from the warranty, operator

must maintain high pressure washer as instructed in this

manual.

BEFORE EACH USE

DANGER: Water spraying from a leak is capable of

injecting material into skin. Inspect hose each time

before using it. Never repair high pressure hose.

Replace it with another hose that meets minimum

pressure rating of your pressure washer.

CHECK AND CLEAN QUICK-

CONNECT SCREEN

Remove quick-connect and examine the inlet screen on the

female connector. Clean if clogged or replace the quick-

connect inlet screen if damaged.

CHECK HIGH PRESSURE HOSE

High pressure hose can develop leaks from wear, kinking,

abuse. Check all hoses for cuts, leaks, abrasions or bulging

of cover, or damage or movement of couplings. If any of

these conditions exist, replace hose immediately.

Figure 10  Connecting the Foamer

GENERAC

Generac 1300PSI Electric High Pressure Washer

CHECK GUN AND WAND

Examine hose connection and make sure it is secure. Test

trigger by pressing it and making sure it springs back into

place when released. Put safety latch in ON position and

test trigger. You should not be able to press trigger.

PURGE PUMP OF AIR AND

CONTAMINANTS

To remove the air from the pump, follow these steps:

 Set up the pressure washer as described in the ASSEMBLY

section and connect the water supply.

 Remove the nozzle attachment from the gun.

 Pull the trigger on the gun and hold.

To remove the contaminant from the pump, follow these steps:

 Set up the pressure washer as described in the ASSEMBLY

section, connect the water supply and start the pressure

washer according to instructions in the OPERATION sec-

tion.

 Remove the nozzle attachment from the gun.

 Pull the trigger on the gun and hold.

 When the water supply is steady and constant, you may

refasten the nozzle attachment and start the pump.

NOZZLE MAINTENANCE

If the nozzle becomes restricted or clogged with foreign mate-

rials, such as dirt, excessive pump pressure may develop. A

partially clogged nozzle can cause a pulsing sensation during

use. This generally is not a pump related problem, but rather

a clogged or partially restricted nozzle.

If the nozzle becomes clogged or partially restricted, imme-

diately clean the nozzle with the kit included with your pressure

washer by following these instructions:

 Shut off the washer and turn off the water supply.

 Separate the nozzle extension from the gun.

 Open the adjustable nozzle to the narrow stream setting.

 Remove the nozzle using the allen wrench provided in the kit.

 Use the wire included in the kit (Figure 11) or a small paper

clip to free the foreign materials clogging or restricting the

nozzle.

Figure 11 - Loosening Debris in Nozzle

GENERAC

Generac 1300PSI Electric High Pressure Washer

 Remove additional debris by back flushing water supply through

wand (Figure 12). Back flush between 30 to 60 seconds. Turn

wand to stream spray while flushing.

 Reinstall the nozzle. Do not overtighten.

 Reconnect the wand to the gun.

 Reconnect the water supply, turn on the water, and start the

washer.

 Test the pressure washer by operating with nozzle in narrow

and expanded streams.

PREPARING THE UNIT FOR

STORAGE

Water should not remain in the unit for long periods of time.

Sediments of minerals can deposit on pump parts and freeze

pump action. If you do not plan to use the Pressure Washer

for more than 30 days, follow this procedure:

1.Shut off the pressure washer, unplug it and let it cool, then

remove all hoses.

2. Store the pressure washer and its components in such a way

as to protect it from freezing.

5.Store in a clean, dry area. Ideally, the unit should be stored

in a frost-free room.

6.Coil the high pressure hose and inspect it for damage. Cuts

in the hose or fraying of it could result in leaks and loss of

pressure. Should any damage be found, replace the hose.

DO NOT attempt to repair a damaged hose. Replace the

hose with the genuine Generac part.

7.Drain water from hose and properly store it to prevent cuts

and general wear.

Figure 12 - Backwashing the Nozzle

TROUBLESHOOTING POINTS

GENERAC

Generac 1300PSI Electric High Pressure Washer

PROBLEM CAUSE CORRECTION

Pressure washer will not start. 1.No electrical power is available. 1. Check cord, plug power, socket.

and fuse.

2.Motor overheats. 2. Turn off the unit. Press trigger of

gun to relieve.pressure on the

unit. Allow unit to cool for about 2

min. It should run when you turn it

ON again.

3.Low voltage. 3. Contact Generac service facility.

4.Trigger not open. 4. Open trigger.

5.Electrical defect. 5. Contact Generac service facility.

Pressure washer does not 1.Pump is sucking air. 1. Water hose must be 1/2-inch

come up to pressure. or greater in diameter.

Be sure water supply is ON.

Be sure water supply is clean.

Check all connections for leaks

or blockage.

Turn OFF the unit, hold trigger in

OPEN position to relieve pressure

and allow air in line to escape.

With trigger still in OPEN position

turn ON the unit. Repeat if

necessary.

2.Water inlet is clogged. 2. Clean water inlet screen.

3.Pump not bled to remove air. 3. Switch OFF washer, press trigger,

switch ON washer while pressing

trigger. Repeat if necessary.

4.Pump is faulty. 4. Contact Generac service facility.

High pressure spray is irregular. 1.Nozzle or water supply is restricted. 1. Unplug unit and clean nozzle.

2.Water supply is inadequate. 2. Turn ON water to full position.

NOTES

GENERAC

Generac 1300PSI Electric High Pressure Washer

EXPLODED VIEW  PUMP AND MOTOR

GENERAC

Generac 1300PSI Electric High Pressure Washer

Drawing No. B1744

PARTS LIST  PUMP AND MOTOR

GENERAC

Generac 1300PSI Electric High Pressure Washer

Drawing No. B1744

1 B1514 1 ASSY, Motor Complete

2 97100 1 CAP, HP

3 21054 1 BOOT, Rubber

4 21055 1 GROMMET, Rubber

5 20138 1 SWITCH, Auto

6 20928 1 HOUSING, Auto-Switch

7 20218 1 CAP, Retainer

8 20213 1 PISTON ASSY, Auto Switch

9 21525 1 WIPER, Piston Bore

10 B1124 1 CAP, Inlet

11 97855 1 O RING, dia. 6.5 x 2.01mm

12 97934 3 O RING, Chk Valve dia. 12.4 x

.78mm

13 20212 1 SPRING, 15.08 x dia. 1.62 CS x

22.3

14 B1565 1 SEAT, Ball

15 B1583 1 SCREW, Lock Socket

16 A1495 2 TAPTITE, M4-0.7x10mm SW

MTG

19 21124 1 RING, Backup dia. 4.34 Id x 1.24

20 21123 1 O RING dia. 3.68 Id x 1.78 CS

[.070"]

21 21126 1 RING, Backup dia. 26.0 ID

22 21125 1 O RING dia. 25.07 ID x 2.62 CS

[.103"]

23 20217 1 STOP, Piston Return

24 A1130 1 SPRING, Pop-off Valve

26 97852 1 BALL, dia. 3/16" Pop-off Valve

29 28739A 1 TIE, Wrap

31 97840 3 O RING,

Hi-press dia. 15.6 x

1.78mm

32 97841 3 CAP, Check Valve

33 97837 1 O RING, Hi-press dia. 9.2 x

2.62mm

34 97835 1 O RING, Hsg Seal, dia. 82.2 x

2.62mm

35 B1026 1 CAP, Vinyl

36 76353A 1 PLUG, Taper dia. 5.4

37 97838 3 ASSY., Check Valve, Inlet

38 A1111A 1 PUMP, Head

39 97839 3 ASSY., Check Valve, Outlet

40 97851 3 O RING, Piston dia. 10.82 x

1.78mm

41 97832 3 PISTON dia. 15 x 65mm

42 40946 4 BOLT, SHCS M6- 1.0 x 35mm

43 93873 7 LOCKWASHER, M6 Ribbed

44 93667 3 SEAL, Piston U Cup

45 97831 3 SPACER, Pilot

46 93680 3 SEAL, Oil-piston dia. 15 TC4

47 20140 1 HOUSING, Piston

48 99503 3 SPRING, Piston Return

49 40945 3 RETAINER, Piston Spring

50 97962 3 BOLT, SHCS M6-1.0 x 20mm

51 97824A 1 BEARING, Needle dia. 40 x

60mm

52 97826 1 WASHER, Brg dia. 40 x 60 x

1mm

53 97825 1 WASHER, Brg dia. 36 x 60 x

6mm

54 97716 1 CAM, Axial 4.3 MM Stroke

55 97829C 1 GEAR, Axial Cam

56 97822 1 BEARING, Ndle Thrust dia. 35 x

52mm

57 20610 1 WASHER, Brg dia. 35 x 55 x

3mm

58 97823 1 WASHER, Brg dia. 35 x 52 x

1mm

59 97834 2 BEARING,

Needle dia. 8 x 12 x

10mm

60 97833 1 SHAFT, Idler Axial Cam

Item Part # Qty. Description Item Part # Qty. Description

EXPLODED VIEW  XXXXXX...

GENERAC

Generac 1300PSI Electric High Pressure Washer

Drawing No. B1744

EXPLODED VIEW  MAIN UNIT

PARTS LIST  MAIN UNIT

GENERAC

Generac 1300PSI Electric High Pressure Washer

Drawing No. B1744

1 N/A 1 ASSY., Motor and Pump (see exp. view B1744 on pages 14 and 15)

2 B1415 1 DECAL, Circuit

3 A1252 1 DECAL, Unit

4 A1313 1 DECAL, Instructions

5 20566 1 DECAL, 1-800 #

6 98806 1 FOAM, Air In, Fan-end

7 97893 1 HOUSING, Switch and Cord

8 20984 1 SWITCH, Rocker 16A

9 98801 4 MOUNT, Rubber

10 97892 1 COVER, Motor

11 20985 1 ENCLOSURE, Rocker Switch Boot

12 20986 1 BOOT, Rocker Switch

13 84543B 2 SCREW, 3.5mm x 12mm Plastite

14 98805 1 CORD, Power

15 84358 4 SCREW, #6-19 x .75 mm Plastite

16 99349 1 STRAIN RELIEF, Cord

17 B1053 1 DECAL, ETL

18 NSP 1 DECAL, Data

19 NSP 1 OVERLAMINATE

20 21334 1 HOUSING, Inlet

21 21335 1 HOUSING, Outlet

22 21265 1 QUICK DISCONNECT, Male

23 96016 1 QUICK DISCONNECT, Female

24 A1484 1 NUT, Strain Relief Lock

25 A1485 1 SEAL RING, Strain Relief

26 97835 1 O RING, Hsg Seal, dia. 82.2 x 2.62mm

27 99350 6 SCREW, #6 Plastite

28 21336 1 GUN, Spray

29 21337 1 WAND, Extension

30 B1417 1 HOSE, High Pressure

31 21338D 1 NOZZLE, Head

32 A1069 1 FOAMER

33 B1051 1 ADAPTER, Accessories

34 87815 1 GOGGLES

35 98904 1 HANG TAG CSA, Nozzle

36 B1236D 1 NOZZLE, 1.15mm dia. (Lilac)

ITEM PART # QTY DESCRIPTION

GENERAC

Generac 1300PSI Electric High Pressure Washer

LIMITED PRESSURE WASHER WARRANTIES (includes Master Contractor)

GENERAC warrants to the original retail purchaser, the pressure washer manufactured by GENERAC to be free from defects in mate-

rial and workmanship for the period(s) set forth below from the date of original purchase. This warranty is not transferable. The term

original purchaser means the person for whom the pressure washer is originally purchased.

Warranty Schedules

Electric Power Washer 1 year (does not apply to commercial or rental operations)

CONSUMER* COMMERCIAL*

Generac GN-Series Engine-driven Engine: 2 years 1 year

Power Washer (2nd year parts only)

Pump: 1 year 90 days

All Other Engine-driven Engine: Warranted solely by Warranted solely by

Power Washers Engine Manufacturer Engine Manufacturer

Pump: 1 year 90 days

* NOTE: For the purpose of this warranty Consumer Use means personal residential household use by original purchaser.

Commercial Use means all other uses, including rental, construction, commercial and income producing purposes. Once a

pressure washer has experienced commercial use, it shall thereafter be considered a commercial use pressure washer for the

purposes of this warranty.

During said warranty period, GENERAC will, at its option, repair or replace any part which, upon examination by GENERAC or GEN-

ERAC Authorized Dealers, is found to be defective under normal use and service**. All transportation costs under warranty, including

return to the factory if necessary, are to be borne by the purchaser and prepaid by the purchaser.

** NORMAL WEAR: As with all mechanical devices, the GN-Series engines need periodic parts service and replacement to

peform well. This warranty will not cover repair when normal use has exhausted the life of a part or an engine.

THIS WARRANTY DOES NOT INCLUDE: Used products and demonstration equipment. Parts such as GUNS, HOSES, WANDS, NOZ-

ZLES or other wear items such as quick couplers, oil, gauges, belts, O-rings, filters, pump packing, etc. Pumps which have been run

without water supplied. Damage or malfunctions resulting from: accidents, abuse, modifications, alterations, or improper servicing. Freez-

ing or chemical deterioration. Normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt,

carbon or lime, etc.).

THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, SPECIFICALLY, GENERAC MAKES NO

OTHER WARRANTIES AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The duration of any implied war-

ranties which cannot be disclaimed is limited to the time period as specified in the express warranty. LIABILITY FOR CONSEQUENTIAL,

INCIDENTAL, OR SPECIAL DAMAGES UNDER ANY AND ALL WARRANTIES IS EXCLUDED, EVEN IF SUCH DAMAGES ARE A

DIRECT RESULT OF GENERACs NEGLIGENCE. Some states do not allow limitations on how long an implied warranty lasts, or the

exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This war-

ranty gives you specific legal rights and you may also have other rights, which vary from state to state.

For service, see your nearest GENERAC authorized warranty service facility or call 1-800-333-1322. Warranty service can be performed

only by a GENERAC authorized service facility. This warranty will not apply to service at any other facility. At the time of requesting war-

ranty service, evidence of original purchase date must be presented.

GENERAC CORPORATION

Simplicity 00776-1 User manual

Brand: Simplicity

Model: 00776-1

Category: High-pressure cleaners

Type: User manual

Download PDF

report

Simplicity 00776-1 User manual

Simplicity 00776-1 User manual

Related papers

Other documents