PR Lighting JNR PAR 18x18 User manual

Brand
PR Lighting
Model
JNR PAR 18x18
Category
Stroboscopes & disco lights
Type
User manual

This manual is also suitable for

JNR PAR 18*18
JNR-8135B
PR LIGHTING LTD.
http://www.pr-lighting.com
1582 Xingye Avenue, Nancun Panyu
Guangzhou, 511442 China
TEL: +86-20-3995 2888
.01.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order
to avoid a hazard.
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
CAUTION
Becareful with your operations.With a dangerous voltage you cansuffer a
dangerous electric shock when touching wires!
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
SAFETY INSTRUCTIONS
1
.10.
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly
connected and must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not
rotate with unbalances.
4) The electric power supply cables must not show any damage, material fatigue or
sediments.
Further instructions depending on the installation spot and usage have to be
adhered by a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a
regular cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights
due to accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make
sure that the circuit contacts are in good condition, prevent the poor contact of
circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.
Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions
under “Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
MAINTENANCE AND CLEANING
10
Disconnect from mains before starting maintenance operation.
CAUTION
Thank you for choosing our JNR PAR 18*18. For your own safety, please read this
manual before installing the device. This manual covers the important information
on installation and applications. Please install and operate the fixture with following
instructions. Meanwhile, please keep this manual well for future needs.
The JNR PAR 18*18 is made of a new type of high temperature strength of cast
aluminum casing with nice outlook. The fixture is designed and manufactured
strictly following CE standards, complying with international standard DMX512
protocol. It’s available independently controlled and linkable with each other for
operation. And it is applicable for large-scale live performances, theater, studio,
nightclubs and discos.
The JNR PAR 18*18 adopts high power LED lamps which features high brightness
and stability. Please carefully unpack it when you receive the fixture and check
whether it is damaged during the transportation. And please check whether the
following items are included inside the box:
.02.
①
UNPACKING
2
JNR PAR 18*18
Signal Cable
Safety Cable
User Manual
1PC
1PC
1PC
1PC
①
②
③
④
.09.
DMX CHANNELS
9
Dimmer,linear dimmer,from dark to bright
Red dimmer,linear dimmer,from dark to bright
Green dimmer,linear dimmer,from dark to bright
Blue dimmer,linear dimmer,from dark to bright
White dimmer,linear dimmer,from dark to bright
Amber dimmer,linear dimmer,from dark to bright
UV dimmer,linear dimmer,from dark to bright
Strobe from slow to fast
0-50:DMX 8CH control;51-100:Saltus Step;101-150:Gradual
change;151--200:Pulse variable;201-255:Sound control;
Function of speed,suspended from slow to fast
DescriptionChannel Function
Dimmer
Red
Green
Blue
White
Amber
UV
Strobe
Selection
Speed
1
2
3
4
5
6
7
8
9
10
10CH Mode
③
②
Euro StandardUK StandardUSA Standard
Power Connector OPTIONAL
④
Specifications
Input Voltage:
LED Quantities:
Control Signal:
Control Channel:
Power Consumption:
Dimensions:
Packing Dimensions:
Net Weight:
Gross Weight:
Features
.03.
FEATURES & SPECIFICATIONS
3
• 18*18W stable and high brightness LEDs (RGBWA+UV)
• Lightweight, compact and easy operation and installation
• Aluminum die-casting structure design with optimum conventional cooling system
• Infinite RGB color mixing system and rainbow effect
• Automatic operation with built-in programs
• DMX512, Master-Slave, Sound Activated and auto operation
• 10 DMX Channels USITT DMX-512
• 8 built-in programs that could be called up via a DMX controller
• 20t/s strobe effect and pulse strobe effect
• 50,000 hours life span and lower power consumption
• 0-100% electronic dimming and blackout for all LEDs
• 25°beam angle default (other angles optional from users)
• LED display
• Dual bracket system available for setting the fixture onthe ground or hanging
• IP rated power IN/OUT
• IP rated 3-pin XLR connectors IN/OUT
• IP65 rated design as for outdoor application
AC90-260V 50/60Hz
18*18W stable and high brightness LEDs (RGBW+UV)
DMX512, master-slave and sound activated or auto operation
10 DMX Channels USITT DMX-512
320W
335(W)*235(D)*300(H)mm
250(W)*250(D)*360(H)mm
6.64kg
14.16kg
.08.
For installations where the DMX cable has to run a long
distance or is in an electrically noisy environment, such as
in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the
digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 Ω resistor
connected between pins 2 and 3,which is then plugged
into the output XLR socket of the last fixture in the chain.
Please see illustrations below.
1
2
3
PIN3
PIN2
120 Ω
MENU OPERATIONS
8
Description
Serial number According Description
1
2
3
4
5
6
7
8
9
10
11
12
A0001
CC00
CP00
DE00
SS00
BEBE
R225
G225
B225
W225
A225
UV255
10CH DMX address setting,(001-512)
Please UP/DOWN to increase/decrease the values
Please UP/DOWN to change the speed
Color fading effect (01-99)
Please UP/DOWN to change the speed
Pluse color change effect(01-99)
Please UP/DOWN to change the speed
Sound control
Color changing effect by sound control
Red dimming,(000-255)
Please UP/DOWN for red dimming
Green dimming,(000-255)
Please UP/DOWN for green dimming
Blue dimming,(000-255)
Please UP/DOWN for blue dimming
White dimming,(000-255)
Please UP/DOWN for white dimming
Amber dimming,(000-255)
Please UP/DOWN for amber dimming
UV Dimming,(000-255)
Please UP/DOWN for UV dimming
Color jumping effects(01-99)
.04.
PHOTOMETRIC DATA
4
25°Beam Angle LUX 0.0929=FC×
Photometric Beam Angle Data
335
300
235
330
235
235
.07.
Regardless of the rigging option you choose for your always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point
for a safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a
carrying handle.
JNR PAR 18*18
Connect the provided XLR cable to the female 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of the par can. You can chain multiple
Par can together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram
below.
DMX-512 connection with DMX terminator
DMX-512 CONTROL CONNECTIONS
7
POWER IN
DMX IN
FUNC
DOWN
DMX IN
POWER IN
UP
ENTER
POWER OUT
DMX OUT
LED DISPLAY
1m (3.3ft)
3m (9.8ft) 5m (16.4ft)0m (0ft)
25°
7m (23.0ft)
71 / 761 8 / 92 1 / 17
(FC/LUX)
249 / 2676 34 / 370
6 / 66
664 / 7150
116 / 1254
44 / 473
13 / 144
14 / 150
2 / 28
267 / 2876
34 / 370 7 / 74
R
G
B
A
W
RGBAW
3 / 32
11 / 123
16 / 170
4 / 47
12 / 135
960 / 10323 119 / 1270 23 / 24642 / 457
DMX Output
3-Pin XLR Socket
DMX Input
3-Pin XLR Socket
1:Ground
2:Data(-)
3:Data(+)
1 2
3
12
3
1
2
3
1
2
3
COMMON
DMX+
DMX-
DMX512 IN
3-PIN XLR
DMX512 OUT
3-PIN XLR
2 1
.05.
Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can
hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such
as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
· The JNR PAR 18*18 is for wash effect for on-site decoration purpose.
· Don’t turn on the fixture if it’s been through severe temperature difference like
after transportation because it might damage the light due to the environment
changes. So make sure to operate the fixture until it is in normal temperature.
· This light should be keep away from strong shaking during any transportation or
movement.
· Don’t pull up the light by only the head, or it might cause damages to the
mechanical parts.
· Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.
· Make sure the installation place is in good safety condition before installing the
fixture.
· Make sure to put the safety chain and check whether the screws are screwed
properly when installing the fixture.
· Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
· Make sure the fixture is operated by qualified personnel who knows the fixture
before using.
· Keep the original packages if any second shipment is needed.
· Don’t try to change the fixtures without any instruction by the manufacturer or
the appointed repairing agencies.
· It is not in warranty range if there are any malfunctions from not following the
user manual to operate or any illegal operation, like shock short circuit, electronic
shock, lamp broke, etc.
OPERATION INSTRUCTIONS
5
INSTALLATIONS
6
.06.
6
Truss installing
Satety Clamp
Safety Cable
from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture
is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the installation
material being used, and periodic safety inspection of all installation material and the
fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the
main power cord to the appropriate wall outlet.
Clamp mounting: The JNR PAR 18*18 provides a unique mounting bracket
assembly, and the safety cable rigging point in one unit (see the illustration below).
When mounting this fixture to truss be sure to secure an appropriately rated clamp to
the handle using a M10 screw fitted through the center hole of the handle. As an
added safety measure be sure to attached at least one properly rated safety cable to
the fixture using on of the safety cable rigging point.
Floor projection
Water proof
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

PR Lighting JNR PAR 18x18 User manual

Brand
PR Lighting
Model
JNR PAR 18x18
Category
Stroboscopes & disco lights
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents